Heat pumps · Chillers · Sludge drying systems
LONGCOM · Longkang Environmental

Sludge dryers

Heat-pump sludge dryers running at 40–80 °C in a closed loop, reducing dewatered sludge volume for municipal, printing and chemical plants.

Heat-pump sludge dryer

A heat-pump sludge dryer removes water from mechanically dewatered sludge by circulating warm dry air through the sludge bed at 40–80 °C inside an insulated enclosure. Moisture evaporated from the sludge is condensed on the cold side of the heat pump and drained away, and the recovered latent heat is returned to the drying air. Because the process runs at low temperature in a closed loop, there is no combustion, minimal exhaust and no need for a high-temperature heat source.

Product series

Batch cabinet dryers

Sludge loaded into trays or carts, dried in cycles. Suited to small and medium plants, or to sites with intermittent sludge output.

Continuous belt dryers

Sludge spread on a perforated belt and conveyed through drying zones. Continuous feed and discharge, suited to larger municipal plants with daily tonnage.

Complete drying lines

Feed hopper, screw conveyor, dryer, discharge, condensate collection and odor control supplied as one line, with a single control interface.

Typical technical parameters

Parameter Typical range Note
Drying air temperature 40–80 °C Low-temperature, no combustion
Inlet moisture content 60%–80% Depends on upstream dewatering
Outlet moisture content 10%–40% Set by downstream disposal route
Volume reduction roughly 50%–75% Relative to dewatered cake
Heat source Closed-loop heat pump Latent heat recovered
Power supply 380 V / 3-phase Per line capacity

Values vary with sludge type, initial moisture, target moisture and ambient conditions. Volume reduction is calculated per project, not taken from a catalog.

Applications and selection notes

Municipal wastewater treatment plants, printing and dyeing, chemical, electroplating, paper, food and pharmaceutical sludge, plus industrial sludge with high organic content.

Selection is driven by four numbers: daily wet sludge tonnage, inlet moisture content, target moisture content, and operating hours per day. The target moisture, in turn, follows the disposal route — landfill, co-incineration, brick making, cement kiln or agricultural use each impose different limits.

A note on the 60% figure. A moisture content around 60% is a commonly cited threshold for landfill disposal of municipal sludge in China. It is not a universal rule for every disposal route: incineration, co-processing and resource utilization each have their own moisture and quality requirements, set by the applicable national or local standard and by the receiving facility. Confirm the actual limit with the disposal operator before fixing the dryer’s outlet moisture.

A note on hazardous waste classification. Whether sludge is classified as hazardous waste depends on its source and test results, not on the equipment. Electroplating and some chemical sludges may be classified as hazardous; municipal sludge generally is not. Classification must be confirmed by testing against the national hazardous waste list and the applicable identification standard.

Frequently asked questions

How low can a heat-pump dryer take the moisture content?

Commonly to 10%–40%, depending on sludge type and drying time. Lower outlet moisture needs longer residence time and more energy per tonne of water removed, so the target should follow the disposal route rather than be pushed to the minimum.

How much volume is actually reduced?

Roughly 50%–75% relative to dewatered cake at 80% moisture, calculated from the mass balance for the specific inlet and outlet moisture contents.

Does low-temperature drying create odor?

The closed loop limits exhaust volume, but sludge drying does release odorous compounds. Condensate and a small air purge are treated — by carbon adsorption, chemical scrubbing or biofiltration — according to the site’s odor sensitivity.

Is the dried sludge still hazardous waste?

The dryer does not change the waste classification. Dried sludge from a hazardous-waste stream remains hazardous waste and must be handled accordingly; drying reduces mass and water content, not the hazard attribute.

What does the line need in terms of utilities?

Three-phase power, a drained and ventilated location, and a connection for condensate to the plant’s wastewater system. No fuel supply and no boiler are required.

What is the typical maintenance scope?

Compressor and fan checks, filter and heat-exchanger cleaning, condensate drain inspection, belt or tray inspection, and calibration of temperature and humidity sensors.

Related reading

Request a quotation

Send the daily wet sludge tonnage, inlet and outlet moisture content, sludge type and analysis, operating hours, disposal route and available power. We return a line configuration with capacity, energy consumption basis and footprint.

Longkang Environmental Equipment Co., Ltd. — air-source heat pump water heaters, water chillers and sludge dryers, supplied with process calculations, interface drawings, commissioning support and spare parts. Phone: +86 400-878-0280 | +86 130-0200-1280