Heat pumps · Chillers · Sludge drying systems
Knowledge

Combining Filter Press Dewatering with Low-Temperature Drying

Why dewater before drying

Drying removes water by evaporation, which costs 300–400 kWh per tonne. Dewatering removes water mechanically, at a cost of a few kWh per tonne. Every percentage point of dry solids gained in the press is water the dryer does not have to evaporate.

Cake dry solids Water per tonne of cake Water to evaporate to 30%
18% 820 kg 743 kg
22% 780 kg 686 kg
28% 720 kg 600 kg
35% 650 kg 500 kg
40% 600 kg 429 kg

Going from 18% to 35% dry solids cuts the evaporation load by about a third. That is why the press specification matters as much as the dryer.

Where the press reaches its limit

Press type Typical cake solids Cycle time Comment
Belt press 18%–22% Continuous Simple, lower solids
Screw press 18%–25% Continuous Low energy, low solids
Plate and frame 30%–40% Batch, 2–4 h Higher solids, labor
Membrane plate 35%–45% Batch, 2–3 h Highest solids, higher cost
Rotary press 20%–30% Continuous Small footprint

The practical limit for a plate press is set by the sludge’s compressibility and the chemical conditioning. Polymers and ferric salts improve dewatering but add mass and can affect the dried product.

Conditioning: the hidden cost and the hidden risk

Conditioner Effect Note
Cationic polymer Flocculation, faster filtration Most common
Ferric chloride plus lime Better solids, higher mass Adds 10%–30% mass
Lime only Raises pH, improves handling Increases solids load
Thermal hydrolysis upstream Much better dewatering High capital

Lime conditioning is a trap in drying projects: it raises the cake solids but adds inert mass that the dryer then has to heat. A cake at 40% solids with 20% lime contains less organic matter than a 30% cake without lime, and the dryer’s throughput per tonne of dry solids falls.

The interface: buffer storage

A filter press is a batch machine and a dryer is continuous. Without a buffer, the dryer stops and starts four times an hour.

Buffer size Suited to Note
4 hours of production Small plant Frequent level alarms
8 hours Normal One shift of buffer
24 hours Large plant Allows weekend operation
3–7 days Plants with transport delays Also a contingency store

The buffer must be covered and ventilated. An open cake store is an odor source and a leachate source, and the leachate has to be returned to the works, not to a surface drain.

Mass balance across the two stages

Stage Input Output Water removed
Press 1,000 kg at 3% DS 100 kg at 30% DS 900 kg (mechanical)
Dryer 100 kg at 30% DS 43 kg at 30% moisture 57 kg (evaporation)
Total 1,000 kg 43 kg 957 kg

Starting from 3% liquid sludge, the press removes 94% of the water mechanically and the dryer removes the rest. The dryer’s energy is spent on the last 6% of the water, which is why the press performance dominates the operating cost.

Drying the cake: what changes

Property Effect on drying
Higher solids Lower evaporation, higher capacity per unit
Polymer residue Can make the cake plastic and sticky
Lime addition Inert mass, lower organic fraction
Fibrous sludge Good bed permeability on a belt
Oily sludge Blinds belts, needs a paddle dryer

A cake at 35% solids from a membrane press dries faster per tonne and produces a more granular product than a 20% cake from a belt press. The press upgrade often pays back through the dryer.

Energy and cost comparison

Configuration Cake solids Evaporation per tonne cake Energy per tonne cake
Belt press plus dryer 20% 714 kg 250 kWh
Plate press plus dryer 32% 543 kg 190 kWh
Membrane press plus dryer 40% 429 kg 150 kWh

Doubling the press capital can cut the drying energy by 40%. On a 20 t/d plant, the difference between 250 and 150 kWh per tonne is 2,000 kWh per day, which is a significant operating cost over a fifteen-year life.

Practical layout

Item Requirement
Press and dryer proximity Under 30 m, or a conveyor
Cake conveyor Enclosed, with a metal detector
Buffer silo Covered, with a level sensor
Return of filtrate To the works inlet
Condensate To treatment, not to surface water
Odor Extract from the buffer and the dryer
Weighing Cake and product, for the mass balance

The weighing is the item most often omitted and the one that proves the plant is working. Without it, the only performance indicator is a moisture sample.

Longkang Environmental Equipment Co., Ltd. sizes the dryer on the measured cake solids from the actual press, not on the press manufacturer’s brochure figure, because a two-point difference in cake solids changes the dryer size by 10%. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions from process designers

What cake solids should I design for?

Use the measured value from the actual press and sludge, not the catalog. If the press is not yet installed, use a pilot test or a conservative figure 2–3 points below the brochure.

Is lime conditioning compatible with drying?

It works but it is inefficient: lime adds mass that has to be heated and reduces the organic content. Use it only if the downstream route requires pH adjustment.

How big should the cake buffer be?

Eight hours of production is the normal minimum; 24 hours gives much more flexibility and is worth the space in a plant that runs a single shift.

Can the dryer take cake directly from the press?

Yes, with a buffer and a variable-speed feeder. Direct feeding without a buffer causes the dryer to cycle and the product moisture to vary.

What happens to the filtrate?

It returns to the head of the works. Its ammonia and COD load is significant and should be in the plant’s load calculation.

Does the dryer need the cake to be crumbled?

Yes, usually. A pre-former or a shredder ahead of the dryer gives a uniform particle size and prevents the belt from blinding.

Related reading

Frequently asked questions