Heat pumps · Chillers · Sludge drying systems
Knowledge

Food Processing Chiller Systems: Hygiene, Load Profile and Heat Recovery

Map the process loads first

Process Temperature Load characteristic Circuit
Raw material chilling 0–4 °C Continuous, varies with intake Glycol or direct expansion
Rapid cooling after cooking 0–5 °C in under 2 h Batch, high peak Glycol, high flow
Cold store −25 to 0 °C Continuous Refrigeration, not chilled water
Fermentation control 8–15 °C Continuous, tight tolerance Chilled water
Packaging area 10–18 °C Continuous Chilled water
Comfort 24–26 °C Working hours Chilled water

Chilled water at 7/12 °C is too warm for most product cooling. Food plants usually need 0–2 °C water, which means glycol, a lower evaporating temperature and a lower COP. Design the process circuit separately from the comfort circuit.

The load profile is flat, and that changes the machine choice

Plant type Load profile Chiller choice
Beverage bottling Flat, 24 h, high Screw, water-cooled, high hours
Meat processing Day shift peak, washdown Screw with VSD, N+1
Dairy Flat with CIP peaks Screw, heat recovery
Bakery Batch peaks Screw plus buffer tank
Prepared meals Two shifts, rapid cooling peaks Screw, glycol, thermal buffer

A flat 24-hour load is the most favorable case for a water-cooled chiller: the capital premium is recovered quickly because the machine runs at high load for 7,000 hours a year.

Glycol circuits: the efficiency penalty

Glycol concentration Freeze point Capacity penalty Pump power penalty
10% −4 °C 3%–5% 8%–12%
20% −9 °C 6%–10% 15%–20%
30% −15 °C 10%–15% 25%–30%
40% −24 °C 15%–20% 35%–45%

Every percent of glycol costs capacity and pump energy. Use the minimum concentration that gives the required freeze protection, and do not specify 30% because “it is safer”.

Hygiene and washdown

Requirement Detail
Chiller location Outside the production area, or in a separate plant room
Panel rating IP65 minimum, IP66 in washdown zones
Materials Stainless or coated, no exposed insulation
Pipework Stainless or food-grade, welded where possible
Insulation Closed cell with a sealed jacket, no fabric facing
Drainage Trapped, with a fall, no ponding
Cleaning Equipment accessible for foam cleaning
Pest control No gaps, no ledges

A chiller in a washdown area will be hosed. If the panel is IP54 and the cable entries are not sealed, water will find the control board within a month.

Food safety documentation

Document Purpose
Material certificates Contact surfaces and insulation
Cleaning procedure For the chiller and the circuit
Temperature log Continuous, with alarm
Change control Any modification recorded
Refrigerant record Charge, leaks, recovery
Commissioning record Flows, temperatures, capacity

Auditors ask for these during a food-safety audit. A chiller without a temperature log is a non-conformity waiting to happen.

Heat recovery: the strongest argument in food plants

A food plant has simultaneous cooling and heating demand: process cooling rejects heat, and CIP (clean-in-place), washdown and boiler feed need hot water at 60–80 °C.

Recovery method Temperature available Share of heating demand
Desuperheater 45–65 °C 15%–25%
Full condenser recovery 35–50 °C 40%–60%
Heat pump on condenser water Up to 75 °C 60%–80%
Dedicated heat recovery chiller 50–70 °C Simultaneous, high

A plant with 1,000 kW of cooling rejects about 1,250 kW of heat. Recovering even a third of it displaces a significant amount of boiler fuel, and the payback is often under three years.

Redundancy for a production line

Criticality Redundancy Comment
Product cooling, single line N+1 on the chiller A stoppage spoils product
Multiple lines N+1 plant, sectional headers One failure does not stop all lines
Cold store 2N or standby Product loss is severe
Comfort N Acceptable

The cost of a chiller failure in a food plant is not the repair; it is the product in the line. That justifies redundancy that a comfort system would never carry.

A configuration example

A prepared-meals plant, 800 kW process cooling at 0 °C, 200 kW comfort:

Item Selection Reason
Process chiller 2 × 450 kW screw, glycol 25% N+1, 0 °C water
Comfort chiller 1 × 250 kW air-cooled Independent, low hours
Buffer tank 10 m³ Smooths batch peaks
Heat recovery Desuperheater on both process machines CIP preheat
Towers 2 cells Turndown
Panel IP66, stainless Washdown
Monitoring Temperature log to the QA system Audit trail

The separate comfort chiller is deliberate: it keeps the process circuit simple and lets the plant run the comfort system only during shifts.

Longkang Environmental Equipment Co., Ltd. supplies food-plant chillers with IP66 panels, stainless frames and a documented cleaning procedure, so the equipment can be included in the plant’s food-safety system rather than treated as an exception. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions from food plant engineers

Can a standard chiller be used in a food plant?

Mechanically yes, but the panel, the materials and the cleaning arrangements usually fail an audit. Specify IP66, stainless and a sealed insulation jacket from the start.

How do I cool product to 0 °C with chilled water?

Use glycol at −2 to 0 °C, or a direct-expansion system. Chilled water at 7 °C cannot cool product to 0 °C.

Is ammonia better than HFC for a food plant?

Ammonia is more efficient and has no GWP, but it needs a machine room with gas detection, qualified operators and a safety regime. Many plants use HFC or HFO systems for smaller loads and ammonia for large central plants.

How much buffer tank do I need?

Enough for 10–20 minutes at peak flow, typically 5–15 m³. The buffer absorbs batch peaks and lets the chiller run at steady load.

What happens during a power failure?

The chiller stops, but the product does not wait. Either provide generator backup for the process circuit or design the process to tolerate a short interruption. Check the cold chain requirement first.

How often should the condenser be cleaned?

Quarterly in a food plant, because airborne fat and flour coat the coil. A coated coil loses capacity quickly and is a fire risk in extreme cases.

Related reading

Frequently asked questions