Heat pumps · Chillers · Sludge drying systems
Knowledge

Sludge Dryer Product Series: Types, Capacities and How to Choose

Capacity is evaporation, not feed tonnage

A dryer quoted as “10 t/day” may mean 10 tonnes of 80% moisture cake, or 10 tonnes of dried product, or 10 tonnes of water evaporated. The three differ by a factor of five.

Basis 10 t/day means Water evaporated Dried product at 30%
Wet cake at 80% moisture 10 t wet 7.14 t 2.86 t
Water evaporation 10 t water 10 t —
Dried product at 30% 10 t dry product 16.7 t 10 t

Always convert to evaporation rate in kg water per hour before comparing quotations. For a plant running 20 hours a day, 7.14 t of water is 357 kg/h.

Water to evaporate = feed mass × (inlet moisture − outlet moisture) ÷ (100 − outlet moisture)

For 10 t of 80% cake dried to 30%: 10,000 × (80 − 30) ÷ 70 = 7,143 kg of water. That is the number the dryer must be sized on.

The series map

Type Evaporation rate Drying temperature Footprint per t water/h Where it fits
Batch cabinet, heat pump 20–150 kg/h 45–65 °C Large Small plants, variable sludge, low odor
Continuous belt, heat pump 150–1,500 kg/h 50–75 °C Moderate Municipal WWTP, food and paper sludge
Multi-stage belt, heat pump 800–3,000 kg/h 60–75 °C Compact Large municipal plants, 24/7 duty
Paddle or disc, steam/oil 500–5,000 kg/h 90–150 °C Compact Industrial sludge, low moisture target
Belt, waste heat 300–2,000 kg/h 60–90 °C Moderate Plants with waste heat available
Solar greenhouse + heat pump 100–1,000 kg/h 35–60 °C Very large Dry climate, land available, low energy cost

Low-temperature heat pump dryers dominate municipal sludge because they stay below the temperature at which odor and ammonia release accelerate, and because the closed loop captures the evaporated water as condensate rather than discharging it as vapor.

What the three main types actually do

Batch cabinet. Wet cake is spread on trays, the cabinet is closed and the heat pump circulates air at 50–65 °C for 8–24 hours. Cheap, tolerant of changing sludge, and easy to operate. The drawbacks are labor, uneven drying between top and bottom trays, and a large footprint for the throughput.

Continuous belt. Cake is extruded into a 10–20 mm layer on a perforated belt, and air passes through the layer as the belt moves through two or three temperature zones. Drying is uniform because the layer thickness is controlled, and the machine runs unattended. This is the standard choice from 150 kg/h upward.

Paddle or disc. Indirect drying: the sludge is agitated against heated surfaces at 90–150 °C. Compact and capable of reaching 10% moisture, but it needs steam or thermal oil, and the higher temperature volatilises ammonia and odorants, so the off-gas treatment becomes a significant cost.

Criterion Batch cabinet Continuous belt Paddle/disc
Moisture uniformity ±5% ±2% ±2%
Labor High Low Low
Off-gas volume Small, closed loop Moderate, closed loop Large, needs scrubbing
Thermal efficiency 2.5–3.0 kg water/kWh 2.8–3.5 kg water/kWh 3.5–4.2 kg water/kWh (with steam)
Turndown 30%–100% 50%–100% 40%–100%
Wear parts Trays, filters Belt, seals, filters Paddles, bearings, seals

The thermal efficiency figure is specific energy consumption expressed the other way: a heat pump dryer removing 3.0 kg of water per kWh is using about 333 kWh per tonne of water evaporated. A paddle dryer on steam at 0.8 MPa uses 1.1–1.3 tonnes of steam per tonne of water, which is 800–950 kWh thermal — cheaper per unit if the steam is waste heat, expensive if it is generated for the purpose.

Selection matrix by sludge source

Sludge source Typical inlet moisture Recommended type Note
Municipal, mechanically dewatered 78%–82% Continuous belt, heat pump The standard case; 60% is the landfill threshold
Municipal, thermally hydrolysed 65%–75% Belt with lower evaporation rate Less water to remove, watch ammonia
Print dyeing 55%–65% Belt or paddle Fibers require a different feed mechanism
Electroplating 70%–80% Belt, stainless wetted parts Heavy metals; condensate may be hazardous
Chemical and pharmaceutical 60%–85% Paddle or belt with solvent-rated components Check for volatile organics and flammability
Food processing 80%–85% Belt, food-grade contact surfaces High organic load, odor control needed
Paper mill 70%–78% Belt or multi-stage Fiber blinds screens; specify a different belt
River and lake dredging 60%–70% Belt with pre-thickening Sand content wears belts and pumps

Two of these need a warning. Solvent-bearing sludge from chemical plants may create a flammable atmosphere inside a dryer — a heat pump dryer is not designed for that and requires an inert-gas or ATEX-rated arrangement. Sludge with high sand content (dredging, some tanneries) abrades belts, screws and pump impellers; specify wear liners and expect a shorter belt life.

The four numbers that size a dryer

Number Symbol How to get it
Feed rate t/h wet Plant records, averaged over a week
Inlet and outlet moisture % Lab test, not the design value
Evaporation rate kg/h Formula above
Operating hours h/day Shift pattern, maintenance window

Then the dryer is sized on evaporation rate at the site’s ambient conditions. A heat pump dryer loses 10%–15% of its rated evaporation in a cold plant room, because the evaporator has to work at a lower temperature — a detail that is omitted from most quotations and discovered in the first winter.

Footprint and services

Evaporation rate Belt dryer footprint Connected power Condensate to drain
200 kg/h 6 × 2.5 m 45–55 kW 0.2 m³/h
500 kg/h 10 × 3.0 m 100–130 kW 0.5 m³/h
1,000 kg/h 14 × 3.5 m 190–240 kW 1.0 m³/h
2,000 kg/h 20 × 4.0 m 350–450 kW 2.0 m³/h

Allow a further 30%–40% for the feed hopper, the discharge conveyor and the maintenance access. Condensate is not clean water: it carries ammonia, volatile fatty acids and a small amount of fines, and it normally returns to the head of the treatment works rather than to the drain.

Longkang Environmental Equipment Co., Ltd. supplies batch cabinet, continuous belt and multi-stage belt dryers from 20 to 3,000 kg/h evaporation, and quotes capacity in kg water per hour at stated inlet and outlet moisture so the figures can be compared with any other offer. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions buyers ask

What does “60% moisture” mean in the landfill standard?

It is the usual acceptance threshold at landfill sites, expressed as a percentage of total wet mass. Drying 80% cake to 60% removes half the water — 5 tonnes from 10 tonnes of cake — and halves the disposal tonnage.

Is a heat pump dryer slower than a thermal dryer?

Per unit of installed footprint, yes; per unit of energy, no. A heat pump dryer takes longer at 60 °C than a paddle dryer at 130 °C, but it uses 250–350 kWh per tonne of water against 800–950 kWh thermal, and it does not need a boiler.

Can one dryer handle several sludge types?

Within limits. A belt dryer can be re-set for different cake, but the extruder, belt speed and temperature zones need adjusting and the control recipe has to change. Where the sludge varies daily, a batch cabinet is more forgiving.

How wet can the feed be?

Belt dryers normally accept 65%–85% moisture. Above 85% the cake is too soft to extrude and sticks to the belt; pre-thickening or a different feed mechanism is needed.

What is the dried product used for?

Incineration, cement kiln co-processing, landfill cover, or landscaping. Each sets a moisture and calorific requirement — cement kilns typically want below 30% moisture, incineration below 40% for autothermal operation, landfill cover below 60%.

Does the dryer need an odor control system?

A closed-loop heat pump dryer concentrates odor in a small air stream and in the condensate, rather than releasing it. Most installations still need carbon filtration on the small exhaust and a covered condensate tank, because the condensate itself smells.

Related reading