Which coil fouls, and why
| Coil | Air side | Fouling type | Effect |
|---|---|---|---|
| Evaporator (cold) | Saturated, 35–50 °C | Lint, fines, biofilm, slime | Airflow drops, evaporating temperature falls, defrost runs longer |
| Condenser (hot) | 55–70 °C, dry | Dust baked on, dried fines | Condensing temperature rises, capacity falls, high-pressure trips |
| Pre-filter | Upstream | Fibers, hair, grit | Pressure drop rises, coils foul faster |
On most sludge dryers the evaporator is the problem coil, because the air leaving the drying chamber carries fine dust and is close to saturation. The condenser fouls more slowly but is harder to clean when it does, because the deposits are baked on.
Detecting fouling before it costs a shift
Four readings tell the story, and all four are on the controller or available with a clamp meter.
| Reading | Clean | Fouled | What it means |
|---|---|---|---|
| Airflow at the belt (m/s) | 2.0–3.0 | Below 1.8 | Blocked coil or filter |
| Evaporator approach (air in − refrigerant) | 5–8 K | Above 10 K | Insulation on the fins |
| Condensing pressure | 1.4–1.7 MPa (R134a) | Above 1.9 MPa | Condenser blocked or overcharged |
| Compressor current | Rated | 8%–15% above rated | Higher condensing pressure |
| Drying time for a fixed batch | Baseline | 15%–30% longer | Combined effect |
| Defrost frequency | 1 per 60–90 min | 1 per 30 min | Restricted airflow |
The cheapest early indicator is the drying time for a known batch. Operators notice that the 20-tonne batch used to finish by 16:00 and now finishes at 19:00, long before anyone looks at a pressure gauge.
Cleaning the evaporator
The evaporator is wet, and wet fines are the hardest deposit to remove without water. Work in this order:
- Isolate and lock off. The compressor and fans must be off, and the main isolator locked. Coil cleaning with live equipment is a fatality waiting to happen, because water and 400 V do not mix.
- Remove the pre-filter and clean it separately. Wash or vacuum, dry fully, and inspect for holes. A torn filter is worse than no filter because it passes clumps.
- Dry-clean first. Compressed air at 2–4 bar, directed through the fins from the clean side, with a vacuum nozzle on the dirty side to catch what comes out. Never blow from the dirty side — that drives the deposit deeper into the fin pack.
- Wet-clean if needed. Low-pressure water at 3–5 bar with a fan-pattern nozzle, again from the clean side, straight through the fins. Higher pressure deforms the fins and closes the air path permanently.
- Use a coil cleaner only where necessary. A mildly alkaline foaming cleaner dissolves biological slime; rinse thoroughly, because residue attracts dust. Do not use acidic coil cleaner on an aluminum fin pack.
- Straighten fins. A fin comb restores the airflow path where the fins have been pushed flat; a 10% flattened area is roughly a 10% airflow loss.
- Dry and restart. Run the fan for 15 minutes before starting the compressor, so the coil is dry and there is no liquid carry-over.
Cleaning the condenser
The condenser is dry and hot, which makes the deposits hard. The same sequence applies with two differences: use a stiff nylon brush as well as air, and expect to need a foaming cleaner more often.
| Deposit | Method | Note |
|---|---|---|
| Loose dust | Compressed air, 3 bar | From the clean side |
| Baked-on fines | Nylon brush, then foaming cleaner | Do not scrape with metal |
| Oily film | Alkaline degreaser, low foam | Rinse at low pressure |
| Biological growth | Biocide cleaner, then rinse | Check the condensate tray after |
The parts that get forgotten
Coil cleaning is only half the job. The rest of the air path fouls too, and each item has its own interval.
| Item | Interval | Method |
|---|---|---|
| Pre-filter | Weekly wash, replace quarterly | Water or vacuum, dry fully |
| Coil (evaporator) | Monthly in sludge duty | Air, then low-pressure water |
| Coil (condenser) | Quarterly | Air, brush, foaming cleaner |
| Condensate tray and drain | Weekly | Flush, check slope, clear biofilm |
| Condensate pump strainer | Monthly | Rinse |
| Belt and rollers | Weekly | Scrape, brush, check tracking |
| Belt wash box | Weekly | Clean nozzles, check water quality |
| Fan impeller | Quarterly | Brush, check balance |
| Door seals and gaskets | Quarterly | Clean, inspect, replace if hardened |
| Temperature and humidity sensors | Quarterly | Wipe, compare with a handheld |
The condensate tray deserves particular attention: a blocked drain backs water into the air path, and the dryer then runs at 100% humidity with no evaporation at all. Operators often diagnose this as “the heat pump has failed” when the fix is a 10-minute drain flush.
A realistic schedule for sludge duty
| Frequency | Task | Time |
|---|---|---|
| Each shift | Record inlet/outlet moisture, throughput, temperatures, compressor current | 10 min |
| Daily | Clean belt and extruder residue, check condensate flow, listen for unusual noise | 30 min |
| Weekly | Wash pre-filter, flush condensate tray, inspect belt tracking | 1 h |
| Monthly | Clean evaporator coil, check defrost behavior, verify sensors | 3 h |
| Quarterly | Clean condenser coil, inspect fan and seals, check refrigerant pressures | 5 h |
| Annually | Full inspection, refrigerant check, electrical torque, performance test against commissioning data | 1–2 days |
In industrial sludge duty — plating, dyeing, chemical — shorten every interval by half, because the air carries more corrosive aerosol and the coils foul faster.
Mistakes that damage the machine
- Pressure-washing the coil at 100 bar. It flattens the fins, and the airflow never comes back. Replace the coil instead.
- Cleaning with the fans running. Water is drawn into the motor and the electrical box.
- Leaving the coil wet. Restarting a wet evaporator immediately frosts the water in the fin pack and can crack the tube-to-header joints.
- Using hydrochloric acid descaler on an aluminum coil. It dissolves the fins in minutes and produces hydrogen.
- Ignoring the filter because “it is only dust”. A blinded filter starves the coil, the evaporating temperature falls, and the dryer defrosts continuously.
- No record. Without a baseline of clean-coil readings, there is no way to tell whether performance has fallen 5% or 25%.
Longkang Environmental Equipment Co., Ltd. fits removable coil access panels and a washable pre-filter on its belt dryers, and supplies a commissioning sheet with the clean-coil airflow, approach temperature and compressor current so fouling can be measured against a real baseline. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from operators
How often should the evaporator coil be cleaned?
Monthly in municipal sludge duty, fortnightly in industrial sludge. Clean on the airflow reading rather than the calendar once a baseline exists: a 15% drop in airflow means clean now.
Can I clean the coil with the dryer hot?
No. Isolate, let the coil come to ambient, and clean cold. Cleaning a hot condenser with cold water can distort the fin pack and the tube joints.
Why does the dryer frost up after cleaning?
Because the coil was left wet, or the airflow is still restricted and the evaporating temperature is too low. Dry the coil with the fan before restarting, and check the filter.
What pressure is safe for coil cleaning?
3–5 bar with a fan nozzle, held at least 150 mm from the fins, working in the fin direction. Above 10 bar, fin damage is almost certain.
Does coil cleaning really restore capacity?
Yes, typically 10%–20% where airflow had fallen 20%–30%. The drying time for a fixed batch is the easiest measure: operators usually see most of the loss return after the first proper clean.
Can I use a normal garden hose?
For the condenser, yes, if the pressure is low and the nozzle is a fan pattern. For the evaporator, a hose alone will not remove wet fines — air first, then water, is the sequence that works.
Related reading
- Sludge dryer maintenance schedule
- Why a sludge dryer falls short of capacity
- Sludge dryer product page
- Odor and condensate from sludge drying