Heat pumps · Chillers · Sludge drying systems
Knowledge

Case Study: Drying Hazardous Chemical Sludge at 20 Tonnes a Day

The problem

Item Detail
Sludge source Effluent treatment of a fine chemical works
Quantity 20 t/day wet cake, 6 days a week
Inlet moisture 82% average, 85% peak
Character Slightly acidic (pH 6.2), chloride 1,800 mg/L, ammonia odor, traces of solvent
Classification Hazardous waste, requires licensed disposal
Current route Tanker to incinerator, 1,200 CNY/t
Annual disposal cost about 7.9 million CNY

Two drivers made the project viable: the disposal cost per tonne, and the fact that the incinerator charged by wet mass. Halving the water halves the invoice.

What was installed

Item Specification Reason
Dryer type Continuous belt, heat pump, closed loop Low temperature limits ammonia and odor release
Capacity 2 × 600 kg/h evaporation 1,080 kg/h required at 20 h/day; one unit covers 55%
Drying temperature 60–70 °C air Above 75 °C the solvent traces volatilise
Belt material 316L stainless Chloride 1,800 mg/L rules out 304
Coil coating Epoxy-coated aluminum fins Ammonia attacks plain aluminum
Cabinet 316L contact surfaces, coated carbon steel frame Condensate is acidic
Condensate handling FRP tank, pH correction, returned to ETP COD 2,400 mg/L, ammonia 900 mg/L
Feed 4-hour buffer hopper with screw feed Filter press discharges in batches
Off-gas Carbon filter on the small exhaust Solvent traces and odor
Discharge 35% moisture cake to covered skip Incinerator accepts below 40%

The drying target of 35% rather than 10% was deliberate. The incinerator accepted below 40%, and drying further would have added 30% to the energy for no disposal benefit.

Commissioning data

Commissioning took nine days, including three days of recipe development on the site’s actual sludge. The figures below are from the eight-hour performance test.

Parameter Design Measured Verdict
Evaporation, unit 1 600 kg/h 612 kg/h 102%
Inlet moisture 82% 82.4% —
Outlet moisture 35% 33.8% Better than target
Air temperature, zone 1 65 °C 64 °C —
Air temperature, zone 3 55 °C 56 °C —
Specific energy 320 kWh/t water 306 kWh/t 4% better
Condensate flow 0.6 m³/h 0.62 m³/h —
Condensate pH 6.5–8.0 6.4 Needs correction, as designed
Noise at 1 m 78 dB(A) 76 dB(A) Within limit
Dust in the exhaust Below 20 mg/m³ 12 mg/m³ Within permit

The specific energy of 306 kWh per tonne of water is the number to compare with alternatives: a paddle dryer on purchased steam would use about 850 kWh thermal per tonne, and an incinerator uses the water content as a penalty on every tonne burned.

The economics

Item Before After Basis
Wet cake to disposal 20.0 t/day 5.5 t/day Mass balance at 35%
Disposal cost 24,000 CNY/day 6,600 CNY/day 1,200 CNY/t
Drying electricity — 4,430 kWh/day 306 kWh/t × 14.5 t
Electricity cost — 3,100 CNY/day 0.70 CNY/kWh
Net daily cost 24,000 CNY 9,700 CNY —
Annual saving — about 4.7 million CNY 330 operating days
Capital — 2.9 million CNY Equipment, installation, services
Simple payback — about 7 months Before maintenance

Seven months is unusually fast, and it is entirely a function of the disposal price. At a landfill gate fee of 300 CNY/t the same project would take four years; at 1,200 CNY/t for hazardous waste it is the most attractive capital project on the site.

Two problems the first design missed

1. The condensate was stronger than expected. The design assumed COD 1,200 mg/L and ammonia 400 mg/L; the actual condensate ran at 2,400 mg/L and 900 mg/L, which overloaded the ETP’s ammonia removal. The fix was a stripping column and a return-flow limit, added at 4% of the project cost — cheap, but it delayed handover by three weeks.

2. The belt blinded in week three. The sludge contains a polymer residue that made the cake plastic and sticky at 60 °C. The belt perforations closed, airflow through the layer collapsed and evaporation fell to 420 kg/h. The remedy was a change of extruder plate geometry, a lower zone-1 temperature and a belt wash with warm water instead of cold — a commissioning recipe issue, not an equipment fault, but it would have been found earlier by a drying test on a 20 kg sample.

What made the installation work

  • A four-hour feed buffer. The filter press discharges 1.5 tonnes every 90 minutes; without the hopper the dryer would run in slugs and the outlet moisture would swing by 8%.
  • 316L everywhere it is wet. The chloride level made 304 a false economy; the material premium was 11% of the equipment cost and the alternative was a belt lasting 18 months.
  • Two units at 55% each. One unit can be cleaned while the other runs, and in winter the pair gives 1,100 kg/h against a 1,080 kg/h duty.
  • A disposal contract that specifies moisture. The incinerator accepts up to 40%; the guarantee to dry to 35% gives a margin against the day the sludge changes.
  • A capped drying temperature. Staying at 70 °C rather than 90 °C kept the solvent traces in the cake and out of the exhaust, which avoided a VOC treatment plant.

Longkang Environmental Equipment Co., Ltd. supplied the two 600 kg/h belt dryers with 316L belts and epoxy-coated coils, and ran a drying test on the customer’s sludge before fixing the extruder plate geometry. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions about chemical sludge drying

Is it safe to dry solvent-bearing sludge?

Only with the right precautions. A closed-loop heat pump dryer at 60–70 °C stays below the flash point of most solvents, but the air loop must be monitored for LEL, and the electrical equipment in the dryer hall must be rated for the zone. Where solvent content is significant, an inert-gas or ATEX-rated arrangement is required, and that is a different machine.

How do I know whether drying will pay back?

Divide the disposal saving per day by the net daily cost of drying. The disposal saving is the reduction in wet mass multiplied by the gate fee; the drying cost is the specific energy multiplied by the water evaporated and the electricity price, plus maintenance at 3%–5% of capital a year.

Can the dried cake be incinerated on site?

Sometimes, and it is worth checking: at 35% moisture the calorific value is typically 6–9 MJ/kg, which can support combustion with auxiliary fuel. Whether the permit allows on-site incineration is a separate question.

What material should the belt be?

316L where chlorides exceed 200 mg/L, 304 otherwise. Titanium is used for very high chloride or low pH, at 2.5–3 times the cost of 316L.

How is the condensate treated?

It normally returns to the head of the effluent plant, with pH correction and, where ammonia is high, stripping. It cannot go to surface water: COD of 2,000–3,000 mg/L and ammonia of 500–1,000 mg/L are typical.

What happens if the disposal route changes?

The dryer gives flexibility: at 35% the cake can go to incineration, cement kiln co-processing or, with further drying, to a landfill that accepts below 60%. Owning the drying step removes the dependence on a single incinerator.

Related reading

Frequently asked questions