How each machine works
| Aspect | Belt dryer | Paddle dryer |
|---|---|---|
| Material path | Spread on a mesh belt, 100–200 mm deep | Stirred in a jacketed trough |
| Heat transfer | Air through the bed, and conduction from below | Conduction from the jacket and the hollow paddles |
| Air flow | High, 0.5–1.5 m/s through the bed | Low, purge only |
| Residence time | 1–4 hours | 1–3 hours, plug flow |
| Temperature | 40–75 °C | 60–150 °C |
| Product form | Granules or flakes | Powder or paste |
The belt dryer is a convective machine: the air carries the moisture away, and the heat pump dehumidifies that air. The paddle dryer is a conductive machine: the jacket and paddles heat the sludge directly, and a small air flow removes the vapor.
Sludge consistency decides more than capacity
| Sludge type | Dry solids after dewatering | Belt | Paddle |
|---|---|---|---|
| Municipal, belt press | 18%–22% | Good, with a pre-former | Poor, sticky |
| Municipal, centrifuge | 22%–28% | Good | Fair |
| Municipal, plate press | 30%–40% | Good | Good |
| Industrial, oily | 20%–30% | Poor, blinds the belt | Good |
| Chemical, crystalline | 30%–50% | Fair | Good |
| Textile, fibrous | 20%–30% | Good | Fair, wraps the paddles |
| Food processing | 15%–25% | Fair | Good |
Sticky, oily or thixotropic sludge blinds a belt and wraps a paddle. Very wet sludge (below 20% dry solids) needs a pre-former or a return-mixing step before either machine will handle it.
Capacity and footprint
| Parameter | Belt dryer | Paddle dryer |
|---|---|---|
| Evaporation per m² of floor | 8–15 kg water/h | 15–25 kg water/h |
| Evaporation per unit volume | Low | High |
| Typical unit capacity | 500–5,000 kg water/h | 300–3,000 kg water/h |
| Footprint for 1,000 kg/h | 80–120 m² | 40–60 m² |
| Height | 3–5 m | 4–8 m |
| Modular scale-up | Add belts or modules | Add units |
The paddle dryer packs more evaporation into a smaller footprint, which matters in an existing building. The belt dryer scales horizontally, which is simpler for very large plants.
Energy and heat source
| Item | Belt | Paddle |
|---|---|---|
| Main heat path | Air, dehumidified by heat pump | Jacket and paddles, hot water or steam |
| Heat pump compatibility | Excellent, closed air loop | Good, with a water circuit |
| Specific energy, heat pump | 300–380 kWh/t water | 320–400 kWh/t water |
| Specific energy, thermal | 800–1,000 kWh/t water | 700–900 kWh/t water |
| Air volume to treat | Large | Small |
| Odor containment | Requires a large enclosure | Easier |
A belt dryer moves a large air volume, so the heat pump and the odor treatment are both sized on that flow. A paddle dryer moves little air, which makes odor containment simpler but requires a heat transfer fluid circuit.
Product characteristics
| Property | Belt | Paddle |
|---|---|---|
| Moisture range | 10%–40% | 5%–30% |
| Particle size | 2–10 mm granules | Fine powder |
| Dust | Low to moderate | High when dry |
| Flowability | Good | Poor at low moisture |
| Re-wetting | Easy | Harder |
| Suitability for cement kiln | Good | Good, but dustier |
| Suitability for land application | Good | Fair, needs granulation |
A belt dryer produces a granular product that is easy to handle and to store. A paddle dryer produces a powder that is dustier and harder to convey, but it can reach lower moisture and is better for very sticky materials.
Maintenance comparison
| Item | Belt | Paddle |
|---|---|---|
| Wear parts | Belt, rollers, seals | Paddles, shaft seals, bearings |
| Belt replacement | Every 2–4 years | Not applicable |
| Seal replacement | Doors, duct joints | Shaft seals, every 1–2 years |
| Cleaning | Belt washing, mesh cleaning | Trough clean-out, harder |
| Access | Good, open frame | Confined space entry |
| Skill level | General mechanical | Mechanical plus alignment |
A paddle dryer’s shaft seals are the critical wear item: sludge finds its way into bearings, and a failed seal contaminates the product and the bearing. Access for cleaning is also harder, which matters for odor and for product changeover.
Selection guidance
| Priority | Recommendation |
|---|---|
| Municipal sludge, 20%–25% DS, large plant | Belt dryer |
| Sticky or oily industrial sludge | Paddle dryer |
| Limited floor space | Paddle dryer |
| Very low final moisture required | Paddle dryer, or belt plus a second stage |
| Granular product for land application | Belt dryer |
| Product to cement kiln | Either; belt is less dusty |
| Frequent product changes or cleaning | Belt dryer |
| Odor-sensitive urban site | Paddle dryer, smaller air volume |
A comparison for a 10 t/d plant
| Item | Belt | Paddle |
|---|---|---|
| Feed | 10 t/d at 80% moisture | Same |
| Water to evaporate (to 30%) | 7.14 t/d | Same |
| Unit size (8 h operation) | 1 belt, about 900 kg/h | 1 unit, about 900 kg/h |
| Footprint | 12 × 6 m | 8 × 5 m |
| Height | 5 m | 7 m |
| Installed power | 280 kW | 300 kW |
| Product | Granules, 25% moisture | Powder, 20% moisture |
| Capital | Baseline | +10%–15% |
Both machines do the job; the choice turns on the sludge, the building and the product market, not on the evaporation figure alone.
Longkang Environmental Equipment Co., Ltd. supplies both configurations and asks for a sludge sample before recommending one, because the behavior of the material on a belt or in a trough cannot be predicted from the moisture content alone. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from process engineers
Which handles the wettest sludge?
Neither handles slurry. Below about 20% dry solids, both need pre-dewatering or return mixing. The paddle dryer tolerates slightly wetter feed because it stirs rather than spreads.
Can a belt dryer handle oily sludge?
Poorly. Oil blinds the mesh and the sludge smears rather than forming a bed. A paddle dryer with a solvent-tolerant seal arrangement is the better choice.
Which produces less dust?
The belt dryer, because the product is granular. A paddle dryer at 10% moisture produces a fine powder that needs enclosed conveying and dust extraction.
How long does the belt last?
Two to four years depending on the material and the cleaning regime. Abrasive sludge shortens it; a spare belt on site avoids a long stoppage.
Can both be heated by a heat pump?
Yes. The belt dryer uses dehumidified air directly; the paddle dryer uses hot water from the heat pump in the jacket and paddles, which requires a water circuit and a larger heat exchanger.
Which is easier to scale up?
The belt dryer, by adding modules or widening the belt. Paddle dryers scale by adding units, which multiplies the maintenance points.
Related reading
- Heat-pump drying versus thermal drying
- Sludge dryer commissioning checklist
- Heat-pump sludge dryer product page