The mechanical wear items
| Item | Function | Replace at | Failure symptom |
|---|---|---|---|
| Conveyor belt | Carrying and supporting the cake | 3–5 years, 2–3 in abrasive sludge | Tracking drift, tears, blinding |
| Belt tensioner and rollers | Keeping the belt aligned | 2–4 years | Belt wander, edge fraying |
| Extruder / pelletiser | Forming the cake layer | 2–3 years, plates 1–2 years | Uneven layer, smeared cake |
| Belt drive gearbox oil | Lubrication | 8,000 h or annually | Noise, overheating |
| Drive chain or belt | Transmitting power | 2–3 years | Slip, wear debris |
| Door seals and gaskets | Keeping the loop closed | 1–2 years | Odor escape, humidity loss |
| Bearing blocks, fan shaft | Supporting the fan | 3–5 years | Vibration, noise |
| Belt wash nozzles | Cleaning the return belt | Clean monthly, replace on block | Belt carries cake back |
| Condensate pump | Removing condensate | 3–5 years | Tray overflow, high humidity |
| Scraper blades | Removing dried cake | 1–2 years | Cake build-up on the belt |
The heat pump wear items
| Item | Replace at | Note |
|---|---|---|
| Compressor contactor | 5–8 years | Same part as a chiller; keep one |
| Filter drier | Every refrigerant opening | Never reuse |
| Expansion valve | 8–12 years | Sticking causes capacity loss |
| Defrost sensors | 5–8 years | Drift causes frequent defrost |
| Pressure transducers | 6–10 years | False high-pressure trips |
| Fan motor | 8–12 years | Bearing failure first |
| Coil (evaporator) | 8–12 years in corrosive duty | Aluminum fins erode in ammonia |
| Controller board | Keep one spare | Longest lead time |
What to stock, by plant size
| Item | 200 kg/h plant | 500 kg/h plant | 1,000 kg/h plant | Lead time |
|---|---|---|---|---|
| Belt repair kit (clips, patch) | 1 | 1 | 2 | 1 week |
| Extruder plates | 1 set | 1 set | 2 sets | 2–4 weeks |
| Door seal set | 1 | 1 | 2 | 1–2 weeks |
| Scraper blades | 2 sets | 2 sets | 3 sets | 1 week |
| Pre-filter elements | 2 | 3 | 4 | 1 week |
| Compressor contactor | 1 | 1 | 2 | 1–2 weeks |
| Filter drier | 1 | 2 | 2 | 1 week |
| Defrost sensor | 2 | 2 | 3 | 1 week |
| Condensate pump | — | 1 | 1 | 1–2 weeks |
| Controller board | 1 | 1 | 1 | 4–8 weeks |
| Bearing set, fan | — | 1 | 1 | 2 weeks |
The two items that stop a plant for a week are the controller board and the belt. A belt can sometimes be repaired with clips for a few days, but a board cannot be improvised, and a board for a six-year-old dryer may already be out of production.
Cost of holding spares
A sensible holding is 2%–4% of the dryer capital cost, replenished at 1%–2% a year.
| Dryer value | Initial spares | Annual replenishment |
|---|---|---|
| 300,000 CNY | 6,000–12,000 CNY | 3,000–6,000 CNY |
| 800,000 CNY | 16,000–32,000 CNY | 8,000–16,000 CNY |
| 2,000,000 CNY | 40,000–80,000 CNY | 20,000–40,000 CNY |
For a municipal plant with a sludge backlog and a landfill contract with penalties, the calculation is not the spares cost but the cost of a week of stockpiled cake — often an order of magnitude larger.
Consumables that are always missing
- Belt clips and a lacing tool — a torn belt can be re-joined in an hour with these.
- Condensate treatment chemicals — biocide and antifoam; a septic condensate tank smells for weeks.
- Coil cleaner — alkaline foaming, plus a low-pressure pump sprayer.
- Silicone grease for door seals — seals harden and leak without it.
- Oven and moisture balance for moisture testing — without these, nobody knows whether the dryer is actually performing.
- A clamp meter and a handheld hygrometer — the two instruments that diagnose most dryer faults.
Storage
Belts degrade: store them rolled, not folded, away from sunlight and ozone, at 10–30 °C. Extruder plates are heavy and wear at the edges — store them flat on a pallet. Seals and gaskets in sealed bags. Controller boards in anti-static packaging, in a dry cabinet. Refrigerant upright.
Keep a spares register with part numbers matched to the machine serial number. Manufacturers revise parts, and a part number from a ten-year-old manual may no longer be valid; the serial number is what the factory needs.
When to repair and when to replace
A dryer reaches the end of its economic life when the cabinet is corroded through, not when the heat pump fails — the heat pump is replaceable, the cabinet is not.
| Age | Condition | Decision |
|---|---|---|
| 0–5 years | Normal wear | Replace wear items on schedule |
| 5–8 years | Belt and extruder wear, coil fouling | Overhaul: belt, seals, coil clean, refrigerant check |
| 8–12 years | Corrosion at the base and door frames, efficiency down 20% | Compare overhaul (30%–40% of new) against replacement |
| Above 12 years | Structural corrosion, parts unavailable | Replace |
An overhaul at year 8 — new belt, new seals, coils cleaned, expansion valve and sensors replaced — costs 30%–40% of a new machine and typically restores 85%–90% of original evaporation. That is usually the right decision, provided the cabinet is sound.
Longkang Environmental Equipment Co., Ltd. supplies a serial-number-matched spares list with every dryer and holds belts, extruder plates and controller boards for models in production. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from plant teams
How long does a conveyor belt last?
Three to five years in municipal sludge, two to three in abrasive industrial sludge. The life is set by belt tracking as much as by abrasion — a belt that wanders rubs its edge and fails early.
Can a torn belt be repaired?
Yes, with clips or a vulcanised splice for a temporary repair, and a proper splice for a permanent one. Keep a repair kit on site; a two-day wait for a technician with a 30-tonne backlog is expensive.
Do I need a spare compressor?
Only for a single-machine plant with no alternative. Most dryer heat pumps use a standard scroll compressor available locally within a week, which makes a spare unnecessary.
How often should the desiccant or filter be changed?
There is no desiccant in a heat pump dryer. The pre-filter is washed weekly and replaced quarterly; the refrigerant filter drier is replaced only when the circuit is opened.
What is the most common cause of dryer downtime?
Belt tracking and extruder blockage, not the heat pump. Both are prevented by the daily check that takes ten minutes.
How do I know the heat pump is losing capacity?
Compare the compressor current and the condensing pressure with the commissioning record at the same air temperature. A 10% rise in current at the same duty means the condenser is fouled or the charge is wrong.
Related reading