Key facts at a glance
| Question | Short answer |
|---|---|
| What does it do? | Moves ambient heat into domestic hot water |
| How efficient is it? | Typical nominal heating COP 3.0–4.5 |
| What are its main parts? | Compressor, evaporator, expansion device, condenser, plus tank and controls |
| What does it replace? | Electric resistance boilers, oil or gas boilers, and standalone solar in some cases |
| What limits performance? | Ambient temperature, water temperature lift, draw-off pattern, defrost behavior |
| Typical hot water temperature | 55 °C standard; 60 °C+ with high-temperature models |
How the cycle works
The machine does not create heat. It collects heat that already exists in the air and lifts it to a temperature useful for domestic hot water, using the same cycle as a refrigerator running in reverse.
Step 1 — Evaporation. Low-pressure liquid refrigerant passes through the evaporator coil. A fan draws outdoor air across the coil. Because the refrigerant’s boiling point is far below ambient temperature, it absorbs heat from the air and evaporates.
Step 2 — Compression. The compressor draws in the low-pressure vapor and compresses it. Compression raises both pressure and temperature, so the vapor leaves the compressor hotter than the water it is about to heat.
Step 3 — Condensation. The hot high-pressure vapor enters the condenser, which is wrapped around or immersed in the water circuit. Heat passes from the refrigerant into the water, and the refrigerant condenses back to liquid.
Step 4 — Expansion. The liquid passes through the expansion device, where pressure and temperature drop sharply, and the cycle repeats.
| Stage | Refrigerant state | Where the heat goes |
|---|---|---|
| Evaporation | Low-pressure liquid to vapor | Absorbs heat from ambient air |
| Compression | Low-pressure vapor to high-pressure vapor | Work added by the compressor |
| Condensation | High-pressure vapor to liquid | Heat released into the water |
| Expansion | High-pressure liquid to low-pressure mixture | Temperature drops, cycle restarts |
Why ambient temperature matters
The evaporator can only absorb heat if the air is warmer than the refrigerant. As ambient temperature falls, the temperature difference shrinks, the evaporator absorbs less heat, and both heating capacity and COP drop. This is why a unit rated at 20 °C ambient will not deliver its nominal output at −5 °C, and why cold-climate projects must check low-temperature capacity rather than nominal capacity.
Below roughly 5 °C, moisture in the air begins to freeze on the evaporator coil. The unit then enters defrost, temporarily reversing the cycle to melt the frost. Defrost is necessary, but it consumes energy and interrupts heating, which is why frost-prone climates need a machine with a sensible defrost strategy rather than a fixed timer.
The four core components
| Component | Function | Typical failure mode |
|---|---|---|
| Compressor | Raises refrigerant pressure and temperature | Winding failure, valve wear, loss of capacity |
| Evaporator (finned coil) | Absorbs heat from ambient air | Fouling, corrosion, blocked airflow |
| Expansion device | Drops refrigerant pressure and temperature | Blockage, loss of control, icing |
| Condenser (plate, coaxial or coil-in-tank) | Transfers heat to water | Scaling, fouling, corrosion |
| Fan and motor | Moves air across the evaporator | Bearing wear, blade damage |
| Controller and sensors | Manages start-up, defrost, safety limits | Sensor drift, parameter error |
In practice, most performance complaints trace back to the heat-exchange surfaces rather than to the compressor: a fouled evaporator or a scaled condenser will reduce capacity long before any component fails outright.
COP and the comparison with other heat sources
| Heating method | Typical seasonal efficiency | Notes |
|---|---|---|
| Electric resistance | COP ≈ 1.0 | One unit of heat per unit of electricity, no more |
| Gas or oil boiler | 85%–95% thermal efficiency | Depends on fuel price and flue losses |
| Air-source heat pump | COP 3.0–4.5 at nominal conditions | Falls in cold weather; still typically above 2.0 |
| Ground-source heat pump | COP 4.0–5.5 | Higher efficiency, much higher drilling cost |
| Solar thermal | Variable | Free energy but weather-dependent and needs backup |
The practical conclusion: an air-source heat pump uses roughly one quarter to one third of the electricity of a resistance heater for the same hot water output. Whether that translates into the lowest operating cost depends on the local electricity tariff, the alternative fuel price, and how well the system is sized.
Product types and how to choose
| Type | Suited to | Watch out for |
|---|---|---|
| Commercial circulating unit | Hotels, schools, hospitals, factories | Needs storage tank and parallel staging design |
| Residential split unit | Homes, small guesthouses | Limited capacity per unit; check electrical supply |
| Residential monobloc unit | Retrofits with limited indoor space | All refrigerant work done at factory; simpler installation |
| Ultra-low-temperature unit | Severe cold regions | Verify low-temperature capacity, not nominal |
| High-temperature unit | Process hot water above 60 °C | Lower COP; confirm material compatibility |
| Pool heating unit | Swimming pools | Corrosion resistance of wetted parts is essential |
Selection should follow the application, not the catalog order. A pool unit and a domestic hot water unit look similar and are not interchangeable: pool water is chlorinated and the evaporator environment is humid and corrosive.
Sizing: three numbers that decide the result
1. Daily hot water demand. Volume in tonnes per day, at the required outlet temperature. This sets the daily energy requirement.
2. Peak-hour demand and simultaneity. The fraction of daily volume drawn in the busiest hour. This sets the storage tank volume and the delivery capacity, not the generation capacity.
3. Design ambient temperature. The local winter design condition. This determines whether the nominal capacity is achievable when it is needed most.
A common sizing error is to divide daily energy by nominal capacity and stop there. That produces a system that works in October and fails in January, because neither the ambient correction nor the peak draw-off has been accounted for.
Installation requirements
- Airflow: clear inlet and outlet, no recirculation of discharged cold air, adequate distance from walls and adjacent units.
- Structure: rooftop installations need a load check and vibration isolation; water-filled tanks are heavy.
- Hydraulics: correct pipe sizing, insulation on hot lines, check valves to prevent thermosiphon losses, and a strainer before the heat exchanger.
- Electrical: three-phase supply for larger commercial units, correctly rated isolator, earth continuity, and protection against water ingress.
- Condensate: a drain path for defrost water, with freeze protection in cold climates.
- Service access: room to remove panels, clean coils and replace a compressor without dismantling the plant.
Common problems and their usual causes
| Symptom | Likely cause |
|---|---|
| Water not reaching setpoint | Undersized capacity, fouled condenser, low refrigerant charge |
| Frequent defrost | High humidity and low ambient, faulty coil sensor, poor airflow |
| High power consumption | Scaling, low ambient operation, excessive standby losses |
| Noise complaints | Fan imbalance, loose panels, missing vibration isolation, unit too close to a bedroom window |
| Unit trips repeatedly | Low water flow, air in the water circuit, electrical fault, high-pressure protection |
Frequently asked questions
What does a heat pump water heater draw in electricity per day?
Heating one tonne of water from 15 °C to 55 °C requires roughly 46 kWh of heat. At a COP of 4, that is about 11.5 kWh of electricity; at a COP of 3, about 15 kWh. Multiply by daily tonnage for a first estimate.
Can it work in freezing weather?
Yes, but capacity and COP decline. Below about −7 °C, standard models lose a significant share of nominal output. Severe cold regions should specify an ultra-low-temperature model and check the low-temperature capacity table.
How long does installation take?
A single residential unit is typically a one-day installation. A commercial plant with tanks, pumps, piping and controls usually takes one to three weeks depending on scale and site readiness.
Does it need a backup heater?
Not usually in mild climates. In cold climates, a small electric backup or a hybrid arrangement is common practice so that the coldest days do not depend solely on the heat pump.
What maintenance does it need?
Coil cleaning every 6–12 months, filter cleaning every 3–6 months, an annual refrigerant charge and leak check, and periodic inspection of electrical terminals and safety devices.
Is it suitable for a hotel with 24-hour demand?
Yes, and it is one of the most common applications. The design uses parallel units charging a large insulated tank, with variable-frequency supply to hold pressure and temperature at peak draw-off.
How long does the equipment last?
A well-maintained commercial unit typically runs 10–15 years. Coil corrosion and compressor wear are the usual life-limiting factors, which is why coastal and industrial atmospheres need a corrosion protection specification.
Choosing a supplier
Ask three questions before signing: what ambient and inlet conditions the capacity figure assumes, what the low-temperature capacity is, and what documentation comes with delivery. A supplier who cannot state the assumptions behind a capacity number is quoting a hope, not a calculation.
Longkang Environmental Equipment Co., Ltd. manufactures air-source heat pump water heaters for commercial and residential projects, with sizing calculations, interface drawings, commissioning support and spare parts. Phone: +86 400-878-0280 | +86 130-0200-1280
Related reading
- Air-source heat pump water heater product page
- How to size an air-source heat pump water heater
- How much electricity does a heat pump use?
- Combining a heat pump with solar thermal
- Heat pump lifespan and warranty terms