Heat pumps · Chillers · Sludge drying systems
Knowledge

Heat Pump and Solar Thermal: How to Combine Them

Why the combination works

A solar collector performs at its peak when the water entering it is cold. A heat pump performs at its peak when the water entering it is warm. Put them in the right order and each covers the temperature band it is good at:

  • Solar raises water from mains temperature (5–20 °C) to 40–55 °C at near-zero marginal cost.
  • The heat pump lifts the remainder to 55–60 °C, at a COP that improves because the evaporator sees a warmer source and the condenser has less lift to cover.

The result is that for the same delivered energy, total electricity falls by roughly the solar fraction divided by the heat pump COP — and the heat pump runs fewer hours, which extends compressor life.

Three practical arrangements

Arrangement How it works Advantage Watch out for
Solar preheat tank → heat pump Collectors charge a preheat tank; heat pump draws from it and delivers to a second tank Simple, each tank at its own temperature, easy to retrofit Two tanks need floor space; preheat tank must be well insulated
Single stratified tank Collectors feed the bottom; heat pump draws from the middle and returns to the top Lowest capital cost, one tank Stratification is easily destroyed by a badly placed return
Solar direct + heat pump backup, same loop Collectors and heat pump share a loop through a plate heat exchanger Compact Control is more complex; freeze protection must cover both

For hotels and hospitals where continuity matters, the two-tank arrangement is the most forgiving: if the collectors are iced or the pump fails, the heat pump still sees mains water and the building still has hot water.

What solar fraction is realistic

Climate Annual solar fraction Summer Winter
High irradiance, dry (north-west China, Mediterranean) 45%–55% 70%–85% 20%–30%
Temperate, mixed (east China, central Europe) 30%–40% 55%–70% 10%–20%
Humid, cloudy (south China coast, UK) 20%–30% 40%–55% 5%–10%

Solar fraction is limited by roof area more often than by climate. A rough planning figure is 1.5–2.5 m² of flat-plate collector per tonne of daily hot water in a good-sun location, and 3–4 m² in a poor one.

Control logic that actually saves energy

The failure mode of most combined systems is not the hardware — it is a controller that lets the heat pump reheat water the collectors have just heated, or that runs the solar pump when the collectors are colder than the tank.

Condition Correct action
Collector temperature exceeds tank bottom by 6–8 K Start solar pump
Collector temperature within 2 K of tank bottom Stop solar pump (hysteresis)
Tank top below setpoint and solar cannot deliver Start heat pump
Solar can reach setpoint alone Lock out heat pump
Tank top above 60 °C Stop all heating; divert or dump if necessary
Frost risk on collectors Drain-back or glycol loop, not a manual intervention

A differential controller with two sensors — one on the collector outlet, one at the tank bottom — is enough. The two errors worth designing out are a fixed-time solar pump schedule and a heat pump setpoint lower than the tank’s solar target.

Worked comparison

A 120-room hotel, 14 t/day at 55 °C, 15 °C mains, 4,000 operating hours. Daily heat demand is 14 × 40 × 1.163 = 651 kWh.

Option Annual electricity Notes
Heat pump only, COP 4.0 59,500 kWh Reference case
Heat pump only, cold-climate, COP 3.6 annual 66,100 kWh Colder site
Solar 35% + heat pump COP 4.2 on the remainder 38,700 kWh 35% of load free, heat pump lift reduced
Solar 35% + heat pump COP 4.2 + off-peak operation 38,700 kWh, lower tariff Storage must be large enough to shift the load

The saving is real but it is not free: collector area, structural loading on the roof, a second tank, and additional controls all carry capital cost, and the payback is usually 4–7 years at commercial tariffs.

Installation points that decide whether it works

  • Freeze protection first. Drain-back systems need a slope all the way to the tank; glycol loops need a correctly sized expansion vessel and annual concentration checks.
  • Insulate the solar loop to the same standard as the hot water loop. An uninsulated 15 m run can lose most of what a small collector array gains.
  • Keep the collector flow rate within the datasheet range. Too low and the panel runs hot and loses efficiency; too high and the pump energy eats the gain.
  • Fit a tempering valve at the outlet if stagnation temperatures above 90 °C are possible.
  • Label the two heat sources clearly on the plant drawing. Most operating errors come from a building manager who does not know which valve belongs to which loop.

Frequently asked questions

Can I add solar to an existing heat pump system?

Usually yes. The cheapest route is a solar preheat tank ahead of the existing tank, with the heat pump drawing from the preheat tank. It avoids modifying the heat pump and keeps the existing controls intact.

Which is more cost-effective, more collectors or a bigger heat pump?

Collectors, up to the point where the roof is full or the summer surplus cannot be used. Beyond a 40%–45% solar fraction, the marginal collector produces hot water that has nowhere to go in summer, and the money is better spent on storage or on the heat pump.

Does the heat pump need a different model in a solar system?

No, but the control interface does need an input from the solar controller. A unit with a dry-contact input for “external heat source active” makes the integration much cleaner than one that only reads its own tank sensor.

What happens in a week of rain?

The heat pump carries the whole load, exactly as it would in a heat-pump-only system. This is why the heat pump must be sized for the full demand, not for the post-solar remainder — otherwise the system fails precisely when the weather is worst.

Is a photovoltaic array a better investment than solar thermal?

It depends on the tariff and the roof. PV plus a heat pump avoids plumbing, glycol and stagnation issues and can export surplus, but it converts sunlight to heat at a lower efficiency than a collector. Where net metering exists, PV is often the simpler choice; where hot water demand is large and constant, thermal collectors usually deliver more useful kWh per m².

How do I know the solar loop is working after handover?

Record three numbers at commissioning: collector outlet temperature, tank bottom temperature, and the temperature rise across the collector array at design flow. If the rise is below the datasheet value on a clear day, the flow rate or the air purge is wrong.

Longkang Environmental Equipment Co., Ltd. supplies the heat pump side of combined systems with a controller input for an external heat source, and will review the solar loop schematic so the two heat sources do not fight each other. Phone: +86 400-878-0280 | +86 130-0200-1280

Related reading