Heat pumps · Chillers · Sludge drying systems
Knowledge

Matching Heat Pump Capacity to Storage Tank Volume

A tank with poorly placed ports behaves like a fully mixed vessel and delivers noticeably less usable hot water than its nominal volume suggests.

Worked example: 60-room hotel

Input Value
Daily volume 7.2 t
ΔT 40 K
Daily energy 335 kWh
Peak-hour demand 12% = 0.86 t/h
Peak energy in that hour 40 kWh
Available heating hours 16 h
Required capacity 335 ÷ 16 = 21 kW
Capacity installed 2 × 12 kW = 24 kW
Tank volume 3.0 t (42% of daily)
Recovery time 3.0 × 40 × 1.163 ÷ 24 = 5.8 h

Check: during the peak hour the tank must supply 40 kWh while the units supply 24 kW × 1 h = 24 kWh. The deficit is 16 kWh, or about 0.35 t of hot water — well within the 3-tonne tank. The design works with margin.

Worked example: the same hotel with a 1.5-tonne tank

Same demand, half the storage. The peak-hour deficit is unchanged, but the buffer is now 1.5 t. At 0.86 t/h draw-off, the tank is depleted in under two hours if the units cannot keep up. Guests at the end of the morning peak get lukewarm water — and the complaints arrive on the busiest day of the year.

The fix is not more heat pump capacity. Doubling capacity would meet the peak, but it would also double cycling losses for the other 22 hours of the day. Increasing the tank is cheaper and more efficient.

Cycling: why oversized capacity costs money

A heat pump that is oversized relative to storage short-cycles: it reaches setpoint quickly, stops, cools slightly, restarts. Each start carries an efficiency and wear penalty, and compressor life is consumed by starts rather than by running hours.

Symptom Cause Remedy
Frequent start-stop Capacity far above demand, small tank Increase tank volume, add staging, enable dead-band
Long runs but never reaches setpoint Capacity below demand, or fouled condenser Check ambient correction, clean heat exchanger
Tank hot at top, cold at bottom Poor stratification, wrong port positions Re-pipe ports, add diffusers
High standby loss Uninsulated tank or long uninsulated runs Insulate tank and lines

Sizing sequence that avoids both errors

  1. Calculate daily volume and daily energy.
  2. Calculate peak-hour volume.
  3. Set tank volume to cover peak-hour volume minus generation during that hour, plus 20% margin.
  4. Set capacity from daily energy ÷ available heating hours, corrected to design ambient.
  5. Check recovery time is acceptable for the building’s operating pattern.
  6. Check the tank fits the plant room and the structure can carry it.

Frequently asked questions

Can the tank be too large?

Yes. Beyond the peak requirement, extra volume adds standing loss, capital cost, structural load and space. A tank at 100% of daily volume is sometimes justified for intermittent buildings, but rarely for a hotel with continuous demand.

Should I use one big tank or several smaller ones?

Several tanks in parallel are easier to install and replace, and can be isolated for maintenance. One large tank stratifies better and has less surface area per unit volume, so it loses less heat.

Does a buffer tank replace a storage tank?

No. A buffer tank smooths short-term fluctuations in a heating or chilled water circuit; a storage tank holds potable hot water. They serve different purposes and are sized differently.

How does the tank affect legionella control?

Storage above 60 °C with a distribution return above 50 °C is the usual control strategy. That means the tank must be rated for the temperature and the heat pump must be able to reach it — a 55 °C-only design cannot.

What insulation thickness is normal?

50–100 mm of polyurethane foam for a commercial tank, with the same on all hot pipework, is standard practice. Thinner insulation on a 3-tonne tank can add several kWh of standing loss per day.

Can I add a tank later?

Usually yes if space and pipework allow, which is one reason to leave room in the plant layout. Retrofitting tanks into an occupied building is far more disruptive than allowing for it at design stage.

Longkang Environmental Equipment Co., Ltd. supplies air-source heat pump units and matched storage tanks, with recovery time and peak coverage stated in the proposal rather than left to the installer. Phone: +86 400-878-0280 | +86 130-0200-1280

Related reading

Frequently asked questions