Wear items and realistic intervals
The intervals below assume a machine running 2,000–3,000 hours a year in a normal plant room. Continuous duty (data center, process) compresses them by roughly 40%.
| Item | Function | Replace at | Failure mode |
|---|---|---|---|
| Compressor contactor | Switching the motor | 5–8 years, or 100,000 operations | Pitted contacts, welded closed |
| Oil filter | Retaining oil cleanliness | 8,000–10,000 h, or annually | Bypass opens, wear debris circulates |
| Oil charge | Lubrication, sealing | Test annually, change 20,000–25,000 h | Acid build-up, viscosity loss |
| Filter drier | Moisture and acid removal | On every refrigerant opening | Saturated, pressure drop |
| Electronic expansion valve | Capacity control | 8–12 years | Sticking, lost steps |
| Pressure transducers | Control and protection | 6–10 years | Drift, then false trips |
| Temperature sensors | Control | 8–12 years | Drift of 1–2 K |
| Flow switch | Low-flow protection | 5–8 years | Stuck paddle, nuisance trip |
| Safety valve | Overpressure protection | Test 3-yearly, replace 8–10 years | Seeping, or stuck shut |
| Fan motor (air-cooled) | Heat rejection | 8–12 years | Bearing noise, winding failure |
| Fan blade and guard | Airflow | On damage | Cracking, imbalance |
| Tube gaskets and O-rings | Water box sealing | Every opening | Hardened, leaking |
| Controller board | Logic and I/O | Keep one spare | Firmware or I/O failure |
| Display panel | Operator interface | Keep one spare on multi-unit sites | Blank screen |
| Strainer basket | Protecting the evaporator | Clean monthly, replace on damage | Perforated, passing debris |
| Refrigerant | Charge | Top up on leak repair | Leak, usually at a joint |
Two entries deserve a note. The controller board is not a wear item, but it is the part that stops a machine for a week: manufacturers revise boards, and a 12-year-old board may be unavailable in year 13. Holding one is cheap insurance on a critical plant. The safety valve is the opposite: it does not fail visibly, and a seized valve is only discovered during a pressure event.
What to stock, by number of machines
| Item | 1 machine | 2–3 machines | 4+ machines | Lead time |
|---|---|---|---|---|
| Compressor contactor | 1 | 2 | 2 | 1–2 weeks |
| Oil filter | 2 | 3 | 4 | 1–2 weeks |
| Filter drier | 1 | 2 | 3 | 1 week |
| Pressure transducer | 1 of each range | 2 | 3 | 1–3 weeks |
| Temperature sensor | 1 | 2 | 3 | 1 week |
| Flow switch | 1 | 1 | 2 | 1 week |
| Tube gasket set | 2 sets | 3 sets | 4 sets | 1 week |
| Controller board | 1 | 1 | 2 | 3–8 weeks |
| Safety valve | 1 | 2 | 2 | 2–4 weeks |
| Refrigerant | 10% of charge | 15% | 20% | 2–4 weeks |
| Fan motor | — | 1 | 1 | 2–6 weeks |
The controller board lead time is the reason it is on the list. Everything else can be air-freighted in a fortnight; a board may not exist.
How much to budget
A reasonable spares holding is 2%–4% of the plant capital cost at commissioning, and 1%–2% a year to replenish. For a 1,000 kW plant at 600,000 CNY, that is 12,000–24,000 CNY up front — roughly the cost of one service visit and one week of downtime, which is the comparison to put to a client who questions it.
| Plant value | Initial spares | Annual replenishment |
|---|---|---|
| 200,000 CNY | 4,000–8,000 CNY | 2,000–4,000 CNY |
| 600,000 CNY | 12,000–24,000 CNY | 6,000–12,000 CNY |
| 2,000,000 CNY | 40,000–80,000 CNY | 20,000–40,000 CNY |
For a plant where downtime stops production, the arithmetic changes completely: an hour of lost output can exceed the whole spares budget, and the correct holding is whatever removes the single point of failure, up to and including a standby compressor.
Consumables that are always forgotten
- Glycol and inhibitor for the loop, plus a refractometer to test concentration.
- Water treatment chemicals — biocide, scale inhibitor, and a test kit.
- Tube brushes sized to the condenser tube ID, and a flexible shaft.
- Gaskets and O-rings for the water boxes, in a sealed bag, labeled.
- Vacuum pump oil and a gauge manifold — most plants have no way to evacuate a circuit.
- Nitrogen for pressure testing and purging while brazing.
- Contact cleaner, fuses, terminal blocks, cable glands — the small items that stop a repair at the last step.
A plant with a 20,000 CNY spares holding and no nitrogen cylinder still cannot repair a leak, because the repair stops at the last operation.
Storage and record keeping
Spares degrade in storage. Keep them in a dry, dust-free store below 40 °C, with O-rings and gaskets sealed against light and ozone, refrigerant upright, and controller boards in anti-static bags. Record the date of receipt and rotate stock — a filter drier that has sat open for two years has absorbed moisture and is worse than nothing.
The register should carry, for each item: part number, quantity, location, date received, machine model it fits, and the date it was last used. A register maintained for three years tells you which items never move and can be dropped, and which items move twice a year and should be stocked deeper.
The overhaul decision
At 8–10 years, a chiller reaches the point where the compressor, the heat exchangers and the controls are all approaching end of life together. An overhaul — compressor strip and rebuild, new bearings, new oil and filters, control board replacement — costs 25%–35% of a new machine and buys another 6–10 years if the shell and tubes are sound.
| Machine age | Action | Trigger |
|---|---|---|
| 0–5 years | Planned maintenance, wear items | Hours or calendar |
| 5–8 years | Condenser cleaning, oil analysis | Approach temperature, oil test |
| 8–12 years | Overhaul assessment | Efficiency drop above 15%, or major failure |
| Above 12 years | Replace or overhaul, compare on lifecycle cost | Parts availability, refrigerant compliance |
The assessment should include a tube inspection (eddy current if the tubes are 10 years old), an oil analysis for wear metals, and a comparison of measured COP against the original commissioning figure. A machine that has lost 20% of its COP and needs a compressor rebuild is usually better replaced, especially if the refrigerant is being phased down.
Longkang Environmental Equipment Co., Ltd. supplies a recommended spares list with every chiller, with part numbers matched to the serial number, and holds boards and compressors for models in production so a critical plant can be back in service within a week. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from facility teams
Which single spare should every plant hold?
The controller board, on any machine that cannot be bypassed. It is the part with the longest lead time and the least substitutable function.
How long can a chiller run without an oil change?
With annual oil analysis, 20,000–25,000 hours is realistic for a screw compressor on a clean circuit. Without analysis, change annually — oil is cheaper than bearings.
Can I use automotive refrigerant?
No. Refrigerant blends are matched to the machine’s expansion device and charge; an unmatched blend changes capacity, pressures and lubrication, and voids the warranty.
Do I need to stock a compressor?
For a single-machine critical plant, consider it — a remanufactured compressor is 30%–40% of a new one and removes a 4–8 week lead time. For a plant with N+1, no.
How often should safety valves be tested?
Every three years by a competent body, and replaced at 8–10 years. A valve that has never lifted may be seized, and the failure only appears when it is needed.
What is the most commonly unavailable part?
Control boards and display panels on machines older than eight years, followed by compressor contactors for obsolete models. Both are cheap to hold and expensive to source in a hurry.
Related reading
- Chiller maintenance schedule
- Chiller lifespan and overhaul decisions
- Chiller fault codes and troubleshooting
- Water chiller product page