Design life by type
| Type | Design life | What limits it |
|---|---|---|
| Air-cooled scroll, small | 10–12 years | Compressor, coil corrosion |
| Air-cooled screw | 12–15 years | Compressor, coil, fans |
| Water-cooled screw | 15–18 years | Compressor, tube fouling, shell corrosion |
| Water-cooled centrifugal | 18–25 years | Compressor bearings, tube bundles |
| Magnetic-bearing centrifugal | 20–25 years | Electronics, VFD, tube bundles |
These are planning figures assuming correct water treatment and annual maintenance. A machine with untreated water can lose its tube bundle in eight years; a well-maintained centrifugal can run for 25.
Component life and the overhaul calendar
| Component | Typical life or interval | Cost if replaced |
|---|---|---|
| Compressor — screw | Overhaul at 20,000–30,000 h; replace at 60,000–80,000 h | 30%–45% of machine price |
| Compressor — centrifugal | Overhaul at 40,000–60,000 h | 20%–35% of machine price |
| Bearings (open-drive) | 40,000–60,000 h | Part of the overhaul |
| Motor windings | 15–20 years with clean power | 20%–30% of machine price |
| Condenser tubes | 12–20 years | 15%–25% of machine price |
| Evaporator tubes | 15–20 years | 20%–30% of machine price |
| Expansion valve / orifice | 10–15 years | Minor |
| Controls and sensors | 10–12 years | 5%–12% of machine price |
| Starter or VFD | 12–15 years | 8%–15% of machine price |
The running-hour clock, not the calendar, should drive the overhaul. A hotel chiller running 2,500 hours a year reaches 30,000 hours in twelve years; a data center machine reaches it in three and a half.
What an overhaul actually includes
- Compressor strip-down, rotor or impeller inspection, clearance measurement.
- Bearing replacement, seal replacement, oil pump inspection.
- Oil change with oil analysis before and after.
- Tube bundle inspection with eddy-current testing where corrosion is suspected.
- Relief valve replacement, control calibration, performance test.
- Refrigerant recovery, evacuation and recharge to the nameplate weight.
A proper overhaul restores 95%–100% of original capacity. A “service” that only changes oil and cleans tubes does not.
Repair or replace: the decision at year 12–15
| Situation | Recommendation | Reasoning |
|---|---|---|
| Compressor failure, machine under 10 years, tubes sound | Overhaul or replace compressor | Remaining life is 5+ years |
| Compressor failure, machine over 15 years | Replace the machine | Two capital events in five years |
| Tube bundle perforated at year 8 | Retube if the shell is sound | Retubing is 20%–25% of a new machine |
| Tube bundle perforated at year 16 | Replace | Retubing plus a compressor overhaul approaches new price |
| Efficiency down 20%+ from fouling that cannot be removed | Retube or replace | The energy penalty pays for the work |
| Controls obsolete, no spares available | Replace controls if the compressor is healthy | Cheaper than a machine |
| Refrigerant R22, major repair needed | Replace with a low-GWP machine | R22 supply is restricted and expensive |
| Refrigerant R134a, mid-life | Keep and plan the transition | R513A or R1234ze at end of life |
A useful financial test: if the repair costs more than 40% of a new machine and the existing machine is beyond 70% of its design life, replacement is usually the better decision — but calculate the energy saving of the new machine as part of the case, because a 15-year-old chiller is often 20%–30% less efficient than its nameplate.
Signs the machine is at end of life
- Repeated refrigerant leaks at multiple joints, suggesting shell or tube degradation.
- Oil analysis showing rising metals (iron, copper, chromium) after each sample.
- Capacity that cannot be restored by cleaning, with approach temperatures above 8 K after brushing.
- Compressor current rising year on year at the same load and condensing temperature.
- Obsolete controls with no available spares, or a refrigerant with restricted supply.
- Corrosion on the shell or water boxes that has been repaired more than once.
Planning the refrigerant transition
Rules under the Kigali Amendment and regional F-gas regulations are reducing HFC availability in steps. For a machine with R134a (GWP 1,430) or R410A (GWP 2,088), the practical options at end of life are R513A (GWP 631) as a retrofit in some machines, or a new machine on R1234ze (GWP under 7). Retrofit is worth investigating only if the machine has more than eight years of life left and the manufacturer supports it in writing.
Frequently asked questions
Is 20 years realistic for a centrifugal chiller?
Yes, for a water-cooled machine with good water treatment, annual tube cleaning and one overhaul. The tube bundle, not the compressor, is usually what ends the life.
How do I know when the compressor needs overhauling?
Running hours are the primary guide, supported by oil analysis (metals and moisture), vibration trend and falling capacity at the same conditions. Do not wait for a failure — a planned overhaul costs a fraction of an emergency replacement.
Does an annual service extend life?
It extends the life of the heat exchangers and the controls more than the compressor. Tube cleaning, water treatment and electrical checks are what separate a 20-year machine from a 12-year one.
Can I replace just the compressor?
Yes, and it is usually the right decision on a machine under ten years old with sound tubes. Confirm the alignment, the oil charge and the control settings, and run a full performance test afterwards.
What is the energy case for replacing an old chiller?
A 15-year-old machine is typically 20%–30% less efficient than a current model at the same conditions, and more at part load. On 1.5 million kWh a year, that is 300,000–450,000 kWh — often enough to justify replacement before the old machine fails.
Should I buy a service contract?
For machines above 500 kW, yes. A contract that includes two visits a year, tube brushing, water treatment review and priority response costs 1.5%–3% of the machine price annually and is cheaper than one emergency repair.
Longkang Environmental Equipment Co., Ltd. supplies the overhaul intervals and the recommended spares list with every chiller, and will review oil analysis results against the machine’s running hours to plan the overhaul before it becomes a failure. Phone: +86 400-878-0280 | +86 130-0200-1280
Related reading
- Water chiller maintenance schedule
- Refrigerant leak detection and repair
- Water chiller cost structure
- Chiller spare parts and replacement intervals