Heat pumps · Chillers · Sludge drying systems
Knowledge

Hospital Chiller Systems: Redundancy, Isolation and Indoor Air Quality

Separate the circuits by criticality

Circuit Serves Temperature Redundancy
Comfort Wards, offices, circulation 7/12 °C N+1
Critical Theatres, ICU, imaging 6/12 °C, humidity controlled 2N or N+1 with automatic transfer
Process Laboratory, pharmacy, CSSD Site specific N+1
Data and equipment Server rooms, MRI 12/18 °C or 15/21 °C 2N

Combining comfort and critical loads on one header is the most common design compromise, and it fails on the day the critical circuit needs cooling while the comfort plant is isolated for maintenance. Separate headers, or at least a cross-connection with automatic valves and a defined priority, are the minimum.

Redundancy: what N+1 actually means here

Configuration Behavior on one failure Suited to
2 × 100% 50% capacity, degraded Comfort, small sites
3 × 50% 67% capacity Comfort with N+1
3 × 50% with cross-connection Critical load maintained Theatres, ICU
2 × 100% with automatic transfer Full capacity Critical, 2N

For theatres, the accepted arrangement is two independent plants, each capable of carrying the critical load, with automatic changeover and generator backup. A single plant with a standby compressor is not redundancy; it is a repair waiting to happen.

Humidity matters as much as temperature

Space Temperature Relative humidity Consequence of deviation
Operating theatre 18–24 °C 30%–60% Infection risk, staff comfort
ICU 22–26 °C 30%–60% Patient comfort, infection
Imaging (MRI, CT) 18–24 °C 30%–60% Equipment faults
Pharmacy 15–25 °C Below 60% Drug stability
Laboratory 20–25 °C 40%–60% Test validity

A chiller supplying 7 °C water can dehumidify, but only if the coil is cold enough and the air is reheated. In a humid climate, a chiller plant alone cannot hold 50% RH in a theatre with a high fresh-air rate; the design needs a dedicated dehumidification or reheating strategy.

Chilled water temperature and the humidity trade-off

Supply temperature Dehumidification Chiller efficiency Comment
5 °C Strong Lower Cold coil, more energy
7 °C Good Standard Normal design
9 °C Weak Higher Only with separate dehumidification
12 °C None Highest Sensible cooling only

Hospitals in humid climates should not adopt the chilled water reset that offices use. The reset saves 2%–3% per Kelvin but can push a theatre above 60% RH, which is a clinical problem.

Emergency power and automatic transfer

Load On generator Transfer time Note
Theatres Yes Under 10 s Surgery cannot stop
ICU Yes Under 10 s Patient safety
Imaging Usually 10–30 s Some equipment has its own UPS
Wards Partly 30 s–2 min Depends on the hospital’s policy
Comfort No — Acceptable

The chiller starting current is the issue: a 500 kW screw machine may draw 1,500 A for a few seconds, which the generator must accept. Confirm the generator sizing with the chiller’s starting method — VSD or soft start reduces the demand substantially.

Water quality and infection control

Risk Control
Legionella in cooling towers Treatment program, drift eliminators, siting away from intakes
Pseudomonas in water systems Sampling, filtration on critical outlets
Corrosion and biofilm in chilled water Water treatment, filtration, annual cleaning
Leaks into clinical areas No pipework above theatres, drip trays, bunding
Cooling tower near fresh-air intake Minimum 20 m, downstream of prevailing wind

The cooling tower is the piece of a chiller plant most associated with hospital infection. Its location relative to fresh-air intakes is a clinical decision as much as an engineering one.

Noise and vibration in clinical areas

Location Limit (typical) Measure
Ward at night 35–40 dB(A) Isolation, low-noise equipment
Operating theatre 40–45 dB(A) Remote plant, lined duct
Imaging suite Per equipment spec Vibration isolation
Plant room adjacent to ward Structure-borne control Floating floor, spring hangers

Imaging equipment is sensitive to vibration as well as temperature, so the chiller and pumps serving an MRI suite are often isolated on separate structures.

A configuration example

A 600-bed hospital, 3,200 kW total cooling, split circuits:

Item Selection Reason
Comfort plant 3 × 900 kW screw, water-cooled N+1, good part load
Critical plant 2 × 500 kW screw, independent 2N for theatres and ICU
Chilled water 7/12 °C comfort, 6/12 °C critical Humidity margin
Towers Separate for each plant No cross-contamination of risk
Generators Critical plant plus 50% comfort Clinical continuity
Heat recovery Desuperheater for DHW preheat Free heat for the boiler
Isolation Each plant can be isolated without affecting the other Maintenance

The separate towers cost more and take more roof space. They also mean a tower outage or a legionella treatment does not take out the theatres.

Longkang Environmental Equipment Co., Ltd. supplies hospital plants with the circuit division, redundancy and generator interface defined at the proposal stage, because those three items determine whether the installation passes commissioning and clinical audit. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions from hospital engineering

Does every hospital need a separate critical plant?

Not every hospital, but every hospital with operating theatres that run while maintenance is happening. A cross-connected single plant with automatic priority can be acceptable in smaller facilities.

How is chiller redundancy proved at handover?

By isolating the largest machine at design load and confirming the remaining plant holds the critical circuits within 30 minutes. This should be a commissioning test with a written record.

Can a chiller plant hold 50% RH in a theatre?

Only with a cold coil and reheat, or a dedicated desiccant/condensation dehumidifier. The chiller supplies the cold water; the air handling design determines the humidity.

What chiller type suits a hospital?

Screw machines are common because they tolerate part load and are easy to service. Centrifugal with VSD suits large base loads. Magnetic bearing machines are attractive where maintenance access is difficult.

How much water treatment is needed?

A managed program with monthly testing, not a dosing pot set and forgotten. Cooling towers are the highest-risk water system in the building.

What about seismic requirements?

In seismic zones, chillers need restrained mounts and flexible connections rated for movement. The plant room layout should allow movement without pipe fracture.

Related reading

Frequently asked questions