Separate the circuits by criticality
| Circuit | Serves | Temperature | Redundancy |
|---|---|---|---|
| Comfort | Wards, offices, circulation | 7/12 °C | N+1 |
| Critical | Theatres, ICU, imaging | 6/12 °C, humidity controlled | 2N or N+1 with automatic transfer |
| Process | Laboratory, pharmacy, CSSD | Site specific | N+1 |
| Data and equipment | Server rooms, MRI | 12/18 °C or 15/21 °C | 2N |
Combining comfort and critical loads on one header is the most common design compromise, and it fails on the day the critical circuit needs cooling while the comfort plant is isolated for maintenance. Separate headers, or at least a cross-connection with automatic valves and a defined priority, are the minimum.
Redundancy: what N+1 actually means here
| Configuration | Behavior on one failure | Suited to |
|---|---|---|
| 2 × 100% | 50% capacity, degraded | Comfort, small sites |
| 3 × 50% | 67% capacity | Comfort with N+1 |
| 3 × 50% with cross-connection | Critical load maintained | Theatres, ICU |
| 2 × 100% with automatic transfer | Full capacity | Critical, 2N |
For theatres, the accepted arrangement is two independent plants, each capable of carrying the critical load, with automatic changeover and generator backup. A single plant with a standby compressor is not redundancy; it is a repair waiting to happen.
Humidity matters as much as temperature
| Space | Temperature | Relative humidity | Consequence of deviation |
|---|---|---|---|
| Operating theatre | 18–24 °C | 30%–60% | Infection risk, staff comfort |
| ICU | 22–26 °C | 30%–60% | Patient comfort, infection |
| Imaging (MRI, CT) | 18–24 °C | 30%–60% | Equipment faults |
| Pharmacy | 15–25 °C | Below 60% | Drug stability |
| Laboratory | 20–25 °C | 40%–60% | Test validity |
A chiller supplying 7 °C water can dehumidify, but only if the coil is cold enough and the air is reheated. In a humid climate, a chiller plant alone cannot hold 50% RH in a theatre with a high fresh-air rate; the design needs a dedicated dehumidification or reheating strategy.
Chilled water temperature and the humidity trade-off
| Supply temperature | Dehumidification | Chiller efficiency | Comment |
|---|---|---|---|
| 5 °C | Strong | Lower | Cold coil, more energy |
| 7 °C | Good | Standard | Normal design |
| 9 °C | Weak | Higher | Only with separate dehumidification |
| 12 °C | None | Highest | Sensible cooling only |
Hospitals in humid climates should not adopt the chilled water reset that offices use. The reset saves 2%–3% per Kelvin but can push a theatre above 60% RH, which is a clinical problem.
Emergency power and automatic transfer
| Load | On generator | Transfer time | Note |
|---|---|---|---|
| Theatres | Yes | Under 10 s | Surgery cannot stop |
| ICU | Yes | Under 10 s | Patient safety |
| Imaging | Usually | 10–30 s | Some equipment has its own UPS |
| Wards | Partly | 30 s–2 min | Depends on the hospital’s policy |
| Comfort | No | — | Acceptable |
The chiller starting current is the issue: a 500 kW screw machine may draw 1,500 A for a few seconds, which the generator must accept. Confirm the generator sizing with the chiller’s starting method — VSD or soft start reduces the demand substantially.
Water quality and infection control
| Risk | Control |
|---|---|
| Legionella in cooling towers | Treatment program, drift eliminators, siting away from intakes |
| Pseudomonas in water systems | Sampling, filtration on critical outlets |
| Corrosion and biofilm in chilled water | Water treatment, filtration, annual cleaning |
| Leaks into clinical areas | No pipework above theatres, drip trays, bunding |
| Cooling tower near fresh-air intake | Minimum 20 m, downstream of prevailing wind |
The cooling tower is the piece of a chiller plant most associated with hospital infection. Its location relative to fresh-air intakes is a clinical decision as much as an engineering one.
Noise and vibration in clinical areas
| Location | Limit (typical) | Measure |
|---|---|---|
| Ward at night | 35–40 dB(A) | Isolation, low-noise equipment |
| Operating theatre | 40–45 dB(A) | Remote plant, lined duct |
| Imaging suite | Per equipment spec | Vibration isolation |
| Plant room adjacent to ward | Structure-borne control | Floating floor, spring hangers |
Imaging equipment is sensitive to vibration as well as temperature, so the chiller and pumps serving an MRI suite are often isolated on separate structures.
A configuration example
A 600-bed hospital, 3,200 kW total cooling, split circuits:
| Item | Selection | Reason |
|---|---|---|
| Comfort plant | 3 × 900 kW screw, water-cooled | N+1, good part load |
| Critical plant | 2 × 500 kW screw, independent | 2N for theatres and ICU |
| Chilled water | 7/12 °C comfort, 6/12 °C critical | Humidity margin |
| Towers | Separate for each plant | No cross-contamination of risk |
| Generators | Critical plant plus 50% comfort | Clinical continuity |
| Heat recovery | Desuperheater for DHW preheat | Free heat for the boiler |
| Isolation | Each plant can be isolated without affecting the other | Maintenance |
The separate towers cost more and take more roof space. They also mean a tower outage or a legionella treatment does not take out the theatres.
Longkang Environmental Equipment Co., Ltd. supplies hospital plants with the circuit division, redundancy and generator interface defined at the proposal stage, because those three items determine whether the installation passes commissioning and clinical audit. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from hospital engineering
Does every hospital need a separate critical plant?
Not every hospital, but every hospital with operating theatres that run while maintenance is happening. A cross-connected single plant with automatic priority can be acceptable in smaller facilities.
How is chiller redundancy proved at handover?
By isolating the largest machine at design load and confirming the remaining plant holds the critical circuits within 30 minutes. This should be a commissioning test with a written record.
Can a chiller plant hold 50% RH in a theatre?
Only with a cold coil and reheat, or a dedicated desiccant/condensation dehumidifier. The chiller supplies the cold water; the air handling design determines the humidity.
What chiller type suits a hospital?
Screw machines are common because they tolerate part load and are easy to service. Centrifugal with VSD suits large base loads. Magnetic bearing machines are attractive where maintenance access is difficult.
How much water treatment is needed?
A managed program with monthly testing, not a dosing pot set and forgotten. Cooling towers are the highest-risk water system in the building.
What about seismic requirements?
In seismic zones, chillers need restrained mounts and flexible connections rated for movement. The plant room layout should allow movement without pipe fracture.
Related reading
- Hotel central air-conditioning chiller configuration
- Water chiller installation and plant room layout
- Water chiller product page
- Hospital hot water by air-source heat pump