Heat pumps · Chillers · Sludge drying systems
Knowledge

Inverter versus Fixed-Speed Chillers: What the Saving Actually Is

What changes with an inverter

Aspect Fixed speed Inverter (VFD)
Capacity control Load/unload with slide valve, or on/off Continuous speed modulation
Minimum stable load 25%–30% 15%–25%
Starting current 2–6 × full load, depending on starter About 1 × full load, soft ramp
Power factor at part load Falls to 0.7–0.8 Above 0.95 with a filter
Condensing temperature control Steps Continuous, tracks the load
Sound at part load Constant, with unload noise Lower, because the compressor slows
Maintenance Standard Standard, plus VFD cooling and filter checks

The saving comes from three mechanisms, in order of size:

  1. No cycling. A fixed-speed machine at 40% load either unloads (with a screw, the slide valve throttles and efficiency drops sharply) or cycles on and off. A VFD machine simply runs slower.
  2. Lower condensing temperature. At reduced speed the condenser has surplus surface, so the machine can float the condensing temperature down, cutting lift.
  3. Better motor efficiency at part load. A well-designed permanent-magnet or inverter-duty motor holds efficiency across the speed range, where a fixed-speed motor is optimized for one point.

Estimating the saving from the load profile

Hours at load Fixed-speed energy, kW·h/year VFD energy, kW·h/year Saving
500 h at 100% 500 × 350 = 175,000 500 × 345 = 172,500 1%
1,500 h at 75% 1,500 × 290 = 435,000 1,500 × 258 = 387,000 11%
1,500 h at 50% 1,500 × 235 = 352,500 1,500 × 185 = 277,500 21%
1,000 h at 30% 1,000 × 195 = 195,000 1,000 × 132 = 132,000 32%
Total 1,157,500 969,000 16%

For a 1,000 kW plant with 350 kW input at full load, that is 188,500 kWh a year, or about USD 17,000 at USD 0.09/kWh. A 15% premium on a USD 150,000 machine is USD 22,500 — so a payback of roughly 16 months in this profile, and no payback at all in a plant that runs flat out.

Where an inverter earns its place

  • Chillers that spend more than 1,500 hours a year below 60% load.
  • Plants with a single large machine and deep night turndown.
  • Sites with weak electrical supply, where the soft start avoids a transformer upgrade.
  • Data centers and hospitals where the load never stops but varies.
  • Any plant where the condenser temperature can float with the load.

Where it does not

  • Process cooling at a constant 100% load, 8,000 hours a year.
  • Very small machines where the VFD cost is a large share of the unit price.
  • Plants with a very short cooling season.
  • Sites where the electrical harmonic environment is already poor and no filter is budgeted.

Electrical points that are often missed

Item Requirement Why
Harmonic mitigation THD below 5% at the point of connection, or a line reactor / active filter VFDs inject harmonics; a weak grid suffers
Cable length to the motor Within the VFD manufacturer’s limit, or use a dv/dt filter Reflected wave damages motor insulation
Motor insulation Inverter-duty, class F or H PWM output stresses windings
Earthing and shielding Screened cable, single-point earth Bearing currents and EMC
VFD cooling Panel air conditioning or filtered ventilation Heat is concentrated in a small enclosure
Bypass arrangement Manual bypass for critical duty Allows running if the drive fails

Maintenance differences

The VFD itself needs little: keep the heatsink and filters clean, check the DC bus capacitors at year 5–7, and keep the panel below 40 °C. The compressor on a VFD machine may run at low speed for long periods, which affects oil return — check that the manufacturer’s minimum speed and oil-return cycle are set correctly, and do not override them to chase a lower load.

Frequently asked questions

Is the saving 10% or 30%?

It depends on the load profile. For a typical hotel or office in a temperate climate, 15%–25% of compressor energy is realistic. For a plant that runs at 80%–100%, it is under 5%.

Does a VFD reduce the maximum capacity?

No, but the machine’s rated capacity is set at nominal speed. Some models deliver slightly more at maximum speed, and the control must be configured so that it does not exceed the motor’s service factor.

Is a VFD chiller harder to maintain?

The chiller is similar; the drive adds a small amount of panel maintenance. The bigger risk is poor harmonic mitigation, which affects other equipment on the site rather than the chiller itself.

Can I retrofit a VFD to an existing chiller?

Sometimes, if the motor is inverter-duty and the compressor has a suitable lubrication system at low speed. For most existing machines the retrofit is not economic compared with replacing the chiller at end of life.

Does an inverter help with starting?

Yes, substantially. The soft ramp draws about full-load current instead of 4–6 times it, which often avoids a transformer or generator upgrade and reduces mechanical stress on the drivetrain.

What about magnetic bearings?

Magnetic-bearing centrifugal machines are inverter-driven by definition and add oil-free operation, which suits data centers and hospitals. They cost more again, and the economics depend on maintenance access and available uptime requirements rather than energy alone.

Longkang Environmental Equipment Co., Ltd. supplies both fixed-speed and inverter-driven chillers and will model the annual energy for a project’s own load profile rather than quoting a generic percentage. Phone: +86 400-878-0280 | +86 130-0200-1280

Related reading

Frequently asked questions