Read the pressure as a temperature
The high-pressure gauge is a thermometer for the condenser. Convert the reading with the refrigerant’s pressure-temperature chart and compare it with the leaving condenser water temperature:
| Refrigerant | Condensing temp | Pressure, absolute | Approach if leaving condenser water is 30 °C |
|---|---|---|---|
| R134a | 33 °C | 0.85 MPa | 3 K — clean and at design flow |
| R134a | 40 °C | 1.02 MPa | 10 K — fouled or flow low; clean now |
| R134a | 45 °C | 1.16 MPa | 15 K — severely fouled, capacity already lost |
| R134a | 50 °C | 1.32 MPa | 20 K — near the trip point |
| R134a | 60 °C | 1.68 MPa | Cut-out range |
| R410A | 35 °C | 2.19 MPa | 5 K — acceptable |
| R410A | 45 °C | 2.72 MPa | 15 K — clean |
| R410A | 55 °C | 3.43 MPa | High |
| R410A | 62 °C | 4.15 MPa | Cut-out range |
Read the table with the actual leaving water temperature: subtract it from the condensing temperature to get the approach. On a 35 °C day with 35 °C condenser water, a healthy machine condenses at 36–38 °C — the absolute pressure is higher than in winter, and that is normal.
For a water-cooled machine, condenser approach = condensing temperature − leaving condenser water temperature. A clean condenser runs at 1–3 K approach; 5–7 K means cleaning is due; above 8 K means the machine is losing capacity and heading for a trip. This single number separates fouling from every other cause.
The five causes
| Cause | Signature | Confirm by | Fix |
|---|---|---|---|
| Fouled condenser tubes | Approach rising slowly over months; high pressure at normal flows | Approach calculation, tube inspection | Brush or chemical clean; water treatment |
| Low cooling water flow | Approach normal but condensing temperature high; pump differential low | Flow measurement, strainer, valve position | Restore flow, clean strainer, set pump |
| Cooling tower underperforming | Condenser water entering above design (e.g. 35 °C instead of 30 °C) | Tower inlet and outlet temperatures, fan operation | Clean fill, repair fan, check spray distribution |
| Non-condensable gas | High pressure with normal approach, erratic readings, high purge activity | Standing pressure test, purge log | Purge, find the air ingress point |
| Overcharge | High discharge and high subcooling | Subcooling measurement | Recover excess, charge by weight |
For low-pressure centrifugal machines using R1234ze or R123, non-condensables accumulate in the condenser and are the classic cause of a slowly rising high-pressure trip that no amount of tube brushing fixes. The purge unit’s run hours are the clue: a purge running continuously is telling you air is entering somewhere.
Five-step diagnosis
Step 1 — Log the trip conditions. Leaving water temperature, entering and leaving condenser water temperature, ambient, load percentage. A trip that only occurs at 100% load on a 38 °C day is a capacity problem; one that occurs at 50% load is a flow or air problem.
Step 2 — Calculate approach. Above 5 K at design flow, clean the condenser before doing anything else.
Step 3 — Measure cooling water flow and temperatures. Design condenser water is usually 30/35 °C. If the entering water is already 35 °C, the tower is the problem, not the chiller.
Step 4 — Check the tower. Fan running, fill clean, distribution nozzles clear, bypass valves closed, tower not recirculating its own discharge.
Step 5 — Check for air and charge. Standing pressure against the PT chart after a long shutdown; subcooling during operation. Recover and recharge only after the leak is found.
Resetting without causing damage
| Situation | Action |
|---|---|
| One trip, cause identified and fixed | Reset and observe a full load cycle |
| Trip repeats within 30 minutes | Lock out; do not reset again |
| Trip with high motor current | Check for liquid slugging and compressor condition |
| Trip after a power interruption | Verify the pump restarted before the compressor |
| Trip on the first hot day of the year | Treat as a capacity or tower performance issue, not a fault |
A chiller that is reset three times in an afternoon without diagnosis often ends up with a damaged compressor thrust bearing — the trip is protecting a machine that is being pushed into a condition it cannot survive.
Prevention
| Measure | Interval | Effect |
|---|---|---|
| Log condenser approach | Weekly | Detects fouling 2–3 months before a trip |
| Brush condenser tubes | Annually, or when approach exceeds 5 K | Restores 5%–15% capacity |
| Water treatment and blowdown control | Continuous | Removes the cause of scaling and biofouling |
| Clean tower fill and strainers | Every 6 months | Restores tower approach |
| Purge run-hour review | Monthly | Detects air ingress early |
| Verify charge by subcooling after service | Every intervention | Prevents overcharge |
Frequently asked questions
Why does it only trip in the afternoon?
Because condensing pressure tracks ambient and load, both of which peak in the afternoon. A condenser with 6 K approach instead of 2 K has used up its margin, and the hottest hour of the hottest day finds the limit.
Is a high-pressure trip dangerous?
It is a protection, not a failure — but repeated trips stress the compressor and can damage valves. Treat the third trip in a day as a stop-work condition.
Can I reduce the load instead of fixing the condenser?
You can, and it will get you through the day. Running at 70% load with a fouled condenser is a temporary measure; the machine will lose capacity permanently if scale is left to harden.
How do I know whether it is fouling or air in the circuit?
Fouling raises the approach; air raises the pressure without raising the approach, and the purge runs more. Compare the two numbers before opening anything.
What is normal condenser approach?
1–3 K for a clean water-cooled condenser at design flow. Above 5 K, plan a clean; above 8 K, the machine is both inefficient and close to tripping.
Does an air-cooled chiller have the same causes?
Mostly, but the “cooling water” side is air. The equivalent checks are coil cleanliness, fan operation, ambient temperature and recirculation between units. Coil fouling in a dusty or greasy environment can cost 20% of capacity in a single season.
Longkang Environmental Equipment Co., Ltd. supplies chillers with condenser approach recorded at commissioning, and the service schedule is built around that number rather than a calendar alone. Phone: +86 400-878-0280 | +86 130-0200-1280
Related reading