Heat pumps · Chillers · Sludge drying systems
Knowledge

Why Air-Source Heat Pumps Defrost, and How the Defrost Logic Works

Demand logic typically saves 8%–15% of the defrost energy compared with a fixed timer, because it stops the unnecessary cycles in mild weather. It needs a clean reference point, though: a coil that was already dirty when the baseline was recorded will defrost on a false signal all winter.

How the heat is delivered to the coil

Method How it works Advantages Drawbacks
Reverse cycle (four-way valve) Reverses refrigerant flow, coil becomes condenser Fast, uses compressor heat, standard Cold air blow at indoor coil, needs suction accumulator
Hot gas bypass Hot discharge gas routed to coil inlet No reversal, stable indoor temperature Additional valve and pipework, slower
Electric heater on coil Resistive element under the coil Very simple, cheap 1:1 energy, significant penalty

Reverse cycle dominates in commercial hot water units. The cost is visible: during a 6-minute defrost the unit produces no hot water and may draw 2–3 kW of compressor power to melt ice, then needs 2–4 minutes to recover. Ten cycles a day at 10 minutes each is 100 minutes — nearly 7% of a 24-hour day — which is the real mechanism behind the winter COP penalty, not the defrost itself.

Meltwater has to go somewhere

This is the most common installation defect found on service visits. During defrost the coil sheds water at a rate of 0.5–1.5 L per cycle for a 20 kW unit. If the base pan drain is blocked, undersized, or runs uphill, that water refreezes around the drain boss and the next cycle’s meltwater has nowhere to go. It then overflows, freezes on the base, and eventually reaches the fan.

  • Slope the base pan to the drain at 1:50 minimum.
  • Use a drain of at least 20 mm inside diameter for units up to 30 kW, 25 mm above.
  • Heat-trace or insulate the drain run in freezing climates, and terminate it into a gully, not onto a walkway.
  • Never common several units into one small drain: simultaneous defrost doubles the flow.
  • On roof-mounted units, check the drain does not discharge onto the roof membrane where it will refreeze and split the waterproofing.

Settings that reduce the penalty

Four adjustments are worth making on any unit that runs through winter, and all of them are recorded in the commissioning sheet:

  1. Extend the interval in dry cold. At −10 °C and 60% RH, frost accumulates slowly; a 90-minute interval is usually enough where 45 minutes is set by default.
  2. Shorten the interval in the damp band. At 2–5 °C with fog or drizzle, 40–50 minutes is realistic regardless of the default.
  3. Terminate on temperature, not on time. A cycle that ends because the timer expired leaves ice at the bottom of the coil; one that ends at +10 °C coil temperature has actually cleared it.
  4. Delay restart by drip-down. Thirty to sixty seconds of fan-only or off time lets the meltwater leave before the coil goes below zero again.

Symptoms and what they mean

Symptom Likely cause First check
Unit defrosts every 30 minutes above 5 °C Coil sensor reading low, or dirty coil Sensor resistance, coil condition
Ice remains at the bottom of the coil Termination temperature too low, drip delay too short Termination setting, drain slope
Water/ice on the base and ground Blocked or undersized drain Drain pan, trace heater
Long defrost, poor recovery Undercharged, or reversing valve leaking Suction pressure, valve temperature
No defrost at all, coil solid Timer not accumulating, sensor failed open Controller status, sensor continuity
Frequent high-pressure trips in defrost Outdoor fan not stopping, or water flow low Fan relay, pump status

Every one of these is a five-minute check with a gauge and a multimeter, which is why the defrost settings belong on the commissioning record next to the water flow rate.

Longkang Environmental Equipment Co., Ltd. supplies units with both time–temperature and demand-based defrost control and publishes the factory default settings in the commissioning manual, so the site engineer can see what was changed and why. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions from installers and operators

At what outdoor temperature does frost stop forming?

Roughly below −8 to −10 °C the absolute humidity is low enough that frost accumulates slowly, and many units defrost less often than at 3 °C. Frost does not stop, but the rate falls sharply.

Why does my unit blow cold air during defrost?

Because reverse-cycle defrost turns the indoor coil into the evaporator. The indoor fan is normally stopped during defrost to prevent this; if it keeps running, check the fan relay and the controller’s defrost output.

Can I disable defrost in summer?

Some controllers allow a seasonal lockout above a set ambient temperature, typically 15 °C. Do not disable it manually — a cool, humid night in summer can still frost the coil when the unit runs at low load.

How much capacity is lost to defrost over a winter?

Allow 5%–8% of seasonal output in a temperate climate with a 0–7 °C winter, and 10%–15% in a damp coastal climate where the 2–5 °C band dominates. This should already be inside the seasonal COP figure, not deducted twice.

Does a coated coil help?

Hydrophilic coating helps condensate sheet off and delays frost bridging between fins by roughly 20%–30% in testing. It does not remove the need to defrost, and it does not tolerate abrasive cleaning.

How often should the coil be cleaned?

Every three months in an urban or industrial environment, twice a year in clean rural air. A dirty coil frosted at the same rate as a clean one looks identical on the controller but delivers 10%–20% less capacity, and no defrost logic can compensate for it.

Related reading

Frequently asked questions