Why the coil decides the service life
The evaporator is the only part of the machine that sees the whole of the outdoor air stream, including dust, pollen, leaves, insects and, in coastal or industrial sites, salt and oily aerosol. A fouled coil does not just lose capacity — it lowers the evaporating temperature, which increases the defrost load, which puts more water on the coil, which attracts more dirt. A 0.1 mm dust layer can cost 3%–5% of capacity; a visibly blocked coil can cost 20%.
| Site condition | Coil cleaning interval | Note |
|---|---|---|
| Clean suburban, low dust | 6 months | Annual deep clean |
| Urban, near road | 3 months | Monthly visual |
| Coastal, within 1 km of sea | 2–3 months, plus fresh-water rinse | Salt attracts moisture |
| Industrial, oily or fibrous dust | Monthly | May need a filter screen |
| Near trees or farmland | 2 months in season | Leaf guards help |
Clean with a low-pressure water jet across the fins, not against them, and use a pH-neutral coil cleaner. Caustic cleaners attack the aluminum fins and the condensate tray coating. Never use a wire brush.
The schedule
| Interval | Task | Who | Acceptance |
|---|---|---|---|
| Weekly | Read display for alarms; note water temperatures | Operator | No active alarm |
| Weekly | Check for water or ice under the unit | Operator | Dry base |
| Monthly | Inspect and clean coil if visible dirt | Operator | Fins visible, light passes |
| Monthly | Check condensate/defrost drain | Operator | Free flow |
| Monthly | Record suction/discharge pressure | Technician | Within range |
| Quarterly | Clean strainer, check pump current | Technician | Flow within 10% design |
| Quarterly | Check electrical terminations for heat | Electrician | No discolouration |
| 6-monthly | Check refrigerant charge by subcooling | Refrigeration engineer | 5–10 K |
| 6-monthly | Test safeties: high pressure, flow, freeze | Technician | Each operates |
| Annually | Deep clean coil, check fan blades and bearings | Technician | No vibration |
| Annually | Inspect insulation and lagging | Technician | No gaps |
| Annually | Check anode if the tank is glass-lined | Technician | Above 50% remaining |
| 3–5 years | Replace contactors, check capacitors | Electrician | Within tolerance |
What an in-house team can do safely
Reading the controller, cleaning the coil from outside, cleaning the strainer with the pump isolated, checking the drain, and recording temperatures need no refrigerant handling. Everything that involves opening the refrigerant circuit, testing charge by pressure alone, or working on the compressor requires a certified engineer in most jurisdictions.
| Task | In-house | Requires certification |
|---|---|---|
| Coil cleaning (external) | Yes | No |
| Strainer cleaning | Yes | No |
| Filter/drain clearing | Yes | No |
| Temperature and pressure logging | Yes | No |
| Charge check by subcooling | No | Yes |
| Leak detection and repair | No | Yes |
| Compressor or valve replacement | No | Yes |
| Electrical protection testing | Qualified electrician | Yes |
Reading the log, not just taking it
A maintenance log is only useful if someone compares it with last month. Three trends catch most developing faults before they become failures:
- Rising discharge pressure at the same water temperature. Points to a fouling coil, a failing fan, or an overcharge.
- Falling ΔT at the same flow. Points to a scaled condenser or a losing charge.
- Increasing defrost frequency. Points to a sensor drift, a restricted airflow or a low charge.
| Trend over three months | Likely cause | Action |
|---|---|---|
| Discharge +2 bar, capacity −5% | Coil fouling | Clean, recheck |
| ΔT −1 K, subcooling −3 K | Slow leak | Leak test, repair, recharge |
| Defrost every 25 min instead of 45 | Coil sensor or airflow | Check sensor, clear obstruction |
| Current +8% at same load | Bearing or valve wear | Vibration check, service |
Water-side maintenance that is usually forgotten
The water side of a heat pump is a closed circuit, so it is easy to assume nothing happens. In practice, oxygen ingress, make-up water and dissimilar metals all cause problems.
- Check the strainer every quarter; a blocked strainer is the single most common cause of a high-pressure trip.
- Test the water annually for pH, conductivity, chloride and hardness. Record it.
- If the system is drained for a shutdown, refill with treated water and vent properly.
- Check the expansion vessel pre-charge annually; a flat vessel causes pressure swings and relief valve weeping.
Spares worth holding
| Part | Quantity for a 1–3 unit site | Why |
|---|---|---|
| Coil cleaner and pump sprayer | 1 set | Monthly use |
| Strainer element | 2 | Cheap, frequently blocked |
| Fan motor capacitor | 1 per model | Common failure, quick fix |
| Contactor | 1 per model | Wear item |
| Pressure switch (HP/LP) | 1 each | Diagnostic substitution |
| Temperature sensor | 2 | Controls faults |
| Pump mechanical seal | 1 | Leak without warning |
| Insulation lagging and tape | 1 roll each | Repair after service |
Holding these reduces a two-day wait for a part to a two-hour repair. They are inexpensive relative to the cost of a cold building.
Longkang Environmental Equipment Co., Ltd. supplies a maintenance card with each unit listing the intervals and the acceptance values, so the schedule can be followed without referring back to the manual. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from facility teams
How often does a commercial heat pump need professional servicing?
Twice a year is the practical answer: one visit before the heating season and one after. Sites with heavy dust or coastal air need quarterly cleaning in addition, which can be done in-house.
Can I clean the coil with a garden hose?
Yes, at low pressure, with the unit isolated and the fins protected. Do not use a pressure washer close to the fins — it flattens them and the damage is permanent. Keep the spray perpendicular to the coil face.
What happens if I never clean the coil?
Capacity falls, defrost frequency rises, discharge pressure climbs and the compressor runs hotter. The unit does not fail immediately; it fails two or three years early, and the energy penalty is paid every day until then.
How do I know if the refrigerant charge is low?
Subcooling below 3 K, bubbles in the sight glass (if fitted), higher superheat, and a discharge temperature that is higher than normal for the load. Pressure alone is not a reliable indicator, because it moves with ambient temperature.
Is it worth taking out a service contract?
For a single small unit, probably not. For a plant with three or more units, a contract with two scheduled visits and a response time commitment is usually cheaper than reactive call-outs, and it keeps the log complete.
Do heat pumps need a winter shutdown?
No. They are designed to run all year. If a building is closed for the winter, either keep the unit on frost protection or drain the water circuit completely — do not simply switch it off with water inside.
Related reading
- Air-source heat pump commissioning checklist
- Air-source heat pump fault codes and troubleshooting
- Air-source heat pump water heater product page