Heat pumps · Chillers · Sludge drying systems
Knowledge

Why a Heat Pump Water Heater Cycles On and Off Constantly

What counts as short cycling

A healthy commercial unit runs for 10 minutes or more per cycle and starts fewer than six times an hour. Below that, the compressor never reaches steady-state efficiency, the oil does not return properly, and the contactor wears out.

Starts per hour Assessment Action
1–3 Normal for a well-matched system None
4–6 Acceptable at low load Watch over a season
7–12 Short cycling Investigate within weeks
Above 12 Severe; damaging Stop and fix before further running

Many controllers enforce a three-minute anti-recycle delay. If the unit starts within three minutes of stopping, that protection has been bypassed or set to zero — restore it first.

The six causes

# Cause How to recognize it Fix
1 Heating capacity too large for the tank Unit reaches setpoint in 4–6 minutes, then waits Add storage or stage the capacity
2 Tank too small for the draw pattern Cycling at peak times, steady at night Increase storage to 40%–60% of daily volume
3 Water flow too low High ΔT, high discharge pressure, trips on high pressure Set pump to design flow; clear strainer
4 Sensor in the wrong place Sensor on the outlet pipe rather than in the tank, or in the stratification layer Relocate to the tank mid-height with a thermowell
5 Differential set too narrow Starts on a 1–2 K drop Widen to 5–8 K, plus a minimum run time
6 Defrost interfering Cycling only in cold, humid weather Check defrost termination and coil sensor

Cause 1 is the most common in retrofits: someone replaces a 30 kW unit with a 60 kW unit to “be safe”, keeps the same 3 m³ tank, and doubles the number of starts.

The relationship between capacity, tank and run time

The run time of one cycle is set by how long the unit takes to raise the tank through the control differential:

Run time (h) ≈ tank volume (m³) × 1.163 × differential (K) ÷ capacity (kW)

A 3 m³ tank, 5 K differential and 60 kW unit gives 3 × 1.163 × 5 ÷ 60 = 0.29 h, or about 17 minutes — acceptable. Halve the tank to 1.5 m³ and the run time falls to 8.7 minutes; double the unit to 120 kW and it falls to 4.4 minutes, which is a cycling problem even though every component is working correctly.

Daily volume Recommended storage Capacity for 8 h heating Resulting run time per 5 K
5 m³ 2–3 m³ 30 kW 23–35 min
10 m³ 4–6 m³ 60 kW 23–35 min
20 m³ 8–12 m³ 120 kW 23–35 min
40 m³ 16–24 m³ 240 kW 23–35 min

The ratio that matters is storage to hourly capacity: roughly 0.05–0.08 m³ of storage per kW. Below 0.04 m³/kW, cycling is all but certain.

Why the sensor matters more than the thermostat

A tank is stratified. The top can be at 55 °C while the bottom is at 20 °C. If the control sensor sits near the inlet, it sees cold water arriving during a draw and starts the unit immediately, even though the tank still holds enough hot water for the next hour. The unit then runs for three minutes, the sensor is satisfied by the incoming flow, and it stops again.

The fix is a sensor in a thermowell at mid-height, plus a control strategy that uses the tank’s usable volume rather than a single point. Some controllers offer a “storage priority” mode that only starts the unit when the tank falls below a set percentage — that alone can remove most of the cycling.

When an inverter is the right answer

A fixed-speed unit can only run at 100% or 0%. Where the load varies widely — a hotel with weekday and weekend occupancy differences, a school with term-time peaks — a variable-speed unit modulates down to 30%–40% and holds instead of stopping. It costs 10%–18% more and usually pays that back in part-load efficiency, but it is not a substitute for adequate storage. Fit the tank first; modulate second.

A short diagnostic sequence

  1. Log the starts over one hour, with the tank temperature at start and stop.
  2. Calculate the run time from the formula above and compare it with the log.
  3. Check the differential setting and the anti-recycle delay.
  4. Check the flow rate and the water-side ΔT.
  5. Check where the control sensor is physically mounted.
  6. Only then consider whether the capacity itself is excessive.

Frequently asked questions

Is short cycling actually damaging?

Yes. Each start draws several times running current, heats the windings, and the repeated stop-start prevents oil from returning to the crankcase. Compressors that cycle heavily fail at the bearings and valves long before their design life.

How many starts per hour is normal?

Fewer than six for a commercial unit, and one to three for a well-matched system. Anything above eight should be investigated; above twelve, stop the unit.

Will a bigger tank really stop it?

In most cases yes, because it increases the run time per cycle. Doubling the storage roughly doubles the run time for the same capacity and differential. It is also cheaper than replacing the unit.

Can I just widen the temperature differential?

You can, within limits. A 5–8 K differential is reasonable; beyond 10 K the delivered water temperature becomes unstable and users notice. Widening the differential is a partial fix, not a substitute for storage.

Why does it cycle only in summer?

In summer the ambient is warm, so the unit’s capacity is at its highest while the heating demand is at its lowest — classic over-capacity at part load. The same unit is well matched in winter. Storage and modulation are the answers.

Does a buffer tank help a system that already has a large tank?

Only if the existing tank is badly stratified or the sensor is in the wrong place. Adding a buffer to a system with 0.08 m³/kW of storage treats the symptom. Fix the control first.

Longkang Environmental Equipment Co., Ltd. sizes the tank and the machine as one calculation and will state the expected run time per cycle in the proposal, so cycling shows up at the design stage rather than in the first week of operation. Phone: +86 400-878-0280 | +86 130-0200-1280

Related reading

Frequently asked questions