Loads: the number that decides the base
Water is 1,000 kg per cubic meter. A 2,000 L tank is two tonnes of water plus 80–150 kg of steel and insulation, and that load sits on four feet or a skirt.
| Tank volume | Water mass | Empty mass (approx.) | Design load to allow |
|---|---|---|---|
| 500 L | 0.5 t | 60 kg | 0.8 t |
| 1,000 L | 1.0 t | 100 kg | 1.4 t |
| 2,000 L | 2.0 t | 160 kg | 2.6 t |
| 5,000 L | 5.0 t | 400 kg | 6.2 t |
| 10,000 L | 10.0 t | 800 kg | 12.0 t |
Add 30%–40% for dynamic and seismic allowance. On a suspended slab, a 5,000 L tank is a structural question, not a plumbing one: spread the load on a steel frame that spans at least two beams, and have the frame checked. On grade, a 150 mm reinforced plinth is normally enough, but the ground beneath it must be compacted, not backfill.
Orientation and stratification
Hot water is lighter than cold, so a tank naturally stratifies: 60 °C at the top, 20 °C at the bottom. That stratification is useful — it lets the heat pump heat only the bottom section while the top stays ready for draw-off. It is destroyed by three things: a high inlet velocity, an inlet that enters at the top, and a tank that is too small for the peak.
| Connection | Position | Detail |
|---|---|---|
| Cold inlet | Bottom, via a diffuser | Velocity below 0.3 m/s at the inlet |
| Hot outlet | Top, with a dip tube if the tank is tall | Take off 50 mm below the dome |
| Heat pump flow | Lower third | Baffle or side-entry diffuser |
| Heat pump return | Upper third | Keep 300 mm from the outlet |
| Sensor pockets | Three heights | Top, middle, bottom for control and monitoring |
| Drain | Lowest point | Full bore, with a hose connection |
A side-entry connection without a diffuser will mix the tank at every start. If the tank has no internal baffle, fit an external diffuser or reduce the pump flow — the cost is a few minutes of work and it protects the whole stratification strategy.
Safety devices that are not optional
| Device | Purpose | Setting | Note |
|---|---|---|---|
| Pressure and temperature relief valve | Prevents tank rupture | 6–7 bar / 90 °C | Discharge to a safe visible point |
| Expansion vessel | Absorbs thermal expansion | Sized on system volume | Pre-charge to cold fill pressure |
| Non-return valve on cold inlet | Prevents backflow | — | Required by most water bylaws |
| Vacuum breaker | Prevents back-siphon on drain-down | — | Often omitted, then tanks implode |
| Anode (if glass-lined) | Sacrificial corrosion protection | Inspect at 2 years | Replace when 50% consumed |
The relief valve discharge must go to a tundish or a drain with a visible air gap, and it must fall continuously — a horizontal run that holds water will corrode and block. Never cap it, and never pipe it to a point where scalding water can reach a person.
Tank materials and when each is right
| Type | Corrosion behavior | Temperature limit | Suited to |
|---|---|---|---|
| Glass-lined steel | Requires anode; fails if anode is neglected | 95 °C | Potable water, most buildings |
| Stainless steel 304 | Good for most mains water | 95 °C | Potable water, soft water areas |
| Stainless steel 316L | Resists chlorides | 95 °C | Coastal, high-chloride water |
| Duplex | High chloride and chloride stress resistance | 95 °C | Coastal, industrial |
| Galvanised | Limited life at high temperature | 70 °C | Not advised for heat pump storage |
For a heat pump system, the tank does not need to be rated above 95 °C, but it does need to hold 60 °C for legionella control. Check that the insulation and any plastic components are rated for that, and that the tank’s warranty covers 60 °C storage — many standard cylinders are warranted only to 70 °C with a reduced life above it.
Pipe insulation: where the losses actually are
Standing loss from a well-insulated 1,000 L tank is roughly 1.5–2.5 kWh per day, which is 5%–10% of a small system’s daily energy. Pipework losses can be larger if the insulation is thin or the fittings are bare.
| Item | Insulation | Loss (W/m or W each at 60 °C) |
|---|---|---|
| DN25 pipe | 30 mm closed cell | 22 W/m |
| DN50 pipe | 40 mm closed cell | 35 W/m |
| DN80 pipe | 50 mm closed cell | 50 W/m |
| Bare valve | — | 40–60 W |
| Insulated valve jacket | 30 mm | 8–12 W |
| Flange pair | 30 mm jacket | 10–15 W |
A 20 m flow-and-return run in DN50 with 40 mm insulation loses about 1.4 kWh per day; the same run with bare valves and flanges at four points adds another 2–3 kWh. That is why the fittings matter more than the straight pipe. Use pre-formed jackets on valves and flanges, seal every joint with contact adhesive, and continue the vapor barrier around supports.
Insulation detailing that survives
- Support the pipe on insulated saddles, not on bare metal cleats.
- Leave a 50 mm gap between the insulation and any hot surface above 80 °C if the material is not rated for it.
- On outdoor runs, use UV-resistant jacketing and seal the ends with a proprietary termination.
- Never compress insulation at a hanger: compression to half thickness roughly doubles the loss.
- Insulate the relief valve discharge? No — leave it visible, but keep it short.
The commissioning checks that catch tank faults
| Check | Acceptance | When |
|---|---|---|
| Base level | Within 3 mm across the tank base | Before filling |
| Tank filled and vented | No air at the top vent | After filling |
| Relief valve lift test | Lifts at setting, reseats | Before handover |
| Expansion vessel pre-charge | Equal to cold fill pressure | Before filling |
| Hot water temperature at outlet | 60 °C storage, 45–50 °C at tap after blending | At steady state |
| Standing loss | Tank holds above 45 °C overnight with no draw | 12-hour test |
| Anode continuity (glass-lined) | Continuity to earth | At handover |
Longkang Environmental Equipment Co., Ltd. supplies tanks with the connection positions and diffuser details marked on the drawing, so the pipework can be prefabricated before the vessel arrives. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from installers
Can a heat pump tank be laid horizontally?
Only if it was designed that way. A horizontal tank stratifies along its length, and the connections and diffusers must be positioned accordingly. Converting a vertical tank to horizontal voids its warranty and ruins stratification.
Does the tank need a secondary return?
If taps are far from the tank, yes. Without it, the first draw is cold and water is wasted. With it, add a small pump and insulate the loop; the pump should run on a timer or a thermostat, not continuously.
How often should the anode be checked?
At two years, then annually once wear is visible. In soft water the anode may last ten years; in aggressive water it can be consumed in three. A tank that leaks at five years is almost always an anode that was never checked.
Is a stainless tank immune to corrosion?
No. 304 stainless pits in water with chloride above about 200 mg/L; 316L raises that threshold but does not remove it. In coastal areas, specify 316L or duplex and flush the tank if it stands idle for long periods.
What temperature should the tank be stored at?
60 °C, with a blending valve at the outlet to bring it down to 45–50 °C at the tap. Storing below 50 °C allows legionella to multiply; storing above 65 °C increases scaling and standing loss.
How do I reduce standing loss further?
Add a 50 mm insulated jacket over the tank if the factory insulation is thin, insulate the top dome (where most heat rises), and fit a thermosyphon trap on the return leg so hot water does not circulate by gravity at night.
Related reading
- Matching heat pump capacity to tank volume
- Heat pump water piping layout
- Air-source heat pump water heater product page