Power supply and distribution
| Item | Requirement | Note |
|---|---|---|
| Supply | 380–415 V, 3-phase, 50 Hz | Confirm with the local utility |
| Connected load | Compressor + fans + conveyors + heaters | Sum, then add 20% diversity |
| Starting current | Up to 3× running for direct-on-line | VFD or soft start for large units |
| Voltage tolerance | ±10% | Compressor protection trips outside |
| Earthing | ≤ 4 Ω, separate earth bar | Equipotential bonding of the frame |
| Isolation | Lockable, within sight of the panel | Maintenance safety |
| Cable entry | Bottom, with a gland plate | Keeps water out |
| Panel rating | IP54 indoors, IP65 outdoors or washdown | Condensate and dust |
Sludge dryers run continuously, so the supply has to be sized for continuous duty, not for intermittent. A cable that is adequate for a 60% duty cycle will run hot at 100%.
The control philosophy in plain terms
| Loop | Sensor | Actuator | What it does |
|---|---|---|---|
| Drying temperature | RTD in the chamber | Compressor capacity, hot gas bypass | Holds 40–75 °C |
| Humidity | Humidity sensor in the exhaust | Fan speed, damper | Controls the drying rate |
| Feed rate | Weight or level | VFD on the feeder | Matches load to capacity |
| Condensate level | Level switch | Transfer pump | Prevents flooding |
| Chamber pressure | Differential pressure | Extract fan | Maintains slight negative pressure |
| Product moisture | Online or manual sample | Feed rate | Trims to the target |
The key idea is that temperature alone does not control moisture. At 60 °C, sludge at 30% moisture and sludge at 60% moisture behave differently, so the controller has to look at the humidity of the exhaust air or at the product moisture, not just the temperature.
Sensors and their installation
| Sensor | Location | Installation detail |
|---|---|---|
| Chamber temperature | Middle of the drying zone | Shielded from direct airflow and radiation |
| Exhaust humidity | In the exhaust duct, after the chamber | Upstream of the condenser, in the main stream |
| Product temperature | At the discharge | Contact with the product, not the belt |
| Condensate level | In the collection tank | High-level alarm plus pump control |
| Differential pressure | Across the air filter | Alarm on high differential |
| Current transformer | On the compressor feed | For load limiting and trend logging |
Mount humidity sensors so that they see the full air stream but not liquid droplets. A sensor coated with condensate reads 100% and the controller will dry the product to death.
PLC logic and interlocks
| Interlock | Condition | Action |
|---|---|---|
| Start sequence | Extract fan, then compressor, then feed | Prevents blocked airflow at start |
| Stop sequence | Feed, then compressor, then fan | Clears the chamber |
| Feed stop on high temperature | Chamber above the limit | Protects the product and the machine |
| Compressor stop on low airflow | Differential pressure low | Prevents overheating |
| Emergency stop | Any E-stop | All motors stop, alarm latched |
| Condensate high level | Level switch | Stops feed, alarm |
| Door open | Limit switch | Stops the fan and the feed |
| Power failure | Supply lost | Safe stop, no automatic restart |
Automatic restart after a power failure should be disabled by default. A dryer that restarts while an operator is inside the chamber is a serious hazard.
VFDs and motor protection
| Motor | Control | Protection |
|---|---|---|
| Compressor | Fixed speed or inverter | Overload, phase failure, high discharge temperature |
| Supply fan | VFD | Overload, belt break detection |
| Extract fan | VFD, pressure control | Overload, differential pressure |
| Feeder | VFD, moisture or weight control | Torque limit, blockage detection |
| Discharge conveyor | Fixed or VFD | Overload, belt alignment |
| Condensate pump | Level control | Dry-run protection |
Set the VFD parameters and record them in the panel. A replaced drive with default parameters will run the fan at the wrong speed, and the drying rate will change without any alarm.
Cabling and installation practice
- Separate power and signal cables by at least 200 mm, and cross at right angles where they must cross.
- Use shielded cable for analogue signals, with the shield earthed at one end only.
- Earth the frame, the panel and the motor bodies to a common bar.
- Use flexible conduit to the motors to allow for vibration.
- Seal every cable entry; condensate travels along a cable.
- Label both ends of every core; a dryer has more sensors than a typical HVAC plant.
| Signal type | Cable | Note |
|---|---|---|
| 4–20 mA analogue | Shielded twisted pair | Earth one end |
| RTD (PT100) | 3-wire shielded | Match the card configuration |
| Digital input | Screened, 24 V DC | Wet contact preferred |
| VFD control | Shielded, separate route | Noise source |
| Communication | Twisted pair, daisy chain | Termination at both ends |
Testing before handover
| Test | Acceptance |
|---|---|
| Insulation resistance | Above 1 MΩ at 500 V |
| Earth continuity | Below 0.1 Ω to the main bar |
| Rotation of each motor | Correct, checked by jog |
| Sensor readings | Match a reference instrument |
| Interlock simulation | Every interlock operates |
| Alarm annunciation | Every alarm appears on the panel and the BMS |
| Setpoint retention | Survives a power cycle |
| Load test | Full load for 2 h, no overheating |
Longkang Environmental Equipment Co., Ltd. provides the panel with a printed I/O list and a setpoint schedule inside the door, so a maintenance electrician can trace a signal without the original drawings. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from electrical contractors
Can the dryer share a supply with the dewatering plant?
It can, if the total load is within the supply capacity and the diversity is realistic. In practice the dryer runs continuously while the press runs in batches, so the combined peak is usually lower than the sum.
Is an inverter necessary on the compressor?
Not always. Fixed-speed compressors with hot gas bypass are common on small dryers and are simpler. Inverters give better part-load efficiency and softer starts on larger units.
What IP rating does the panel need?
IP54 minimum indoors. In a washdown area or outdoors, IP65 with a sunshade. Condensate and sludge dust are both conductive enough to cause tracking.
Do I need gas detection?
For municipal sludge at 40–75 °C, methane generation is limited but not zero. In an enclosed chamber or a basement plant room, fit methane detection and ventilation. For industrial sludge, check the analysis first.
How do I handle a sensor failure at night?
Configure the controller to hold the last good value for a defined period and raise an alarm, rather than tripping the plant. A dryer that stops at 2 a.m. because a humidity sensor failed will be restarted with wet sludge in the chamber.
Can the control system report to a SCADA system?
Yes, over Modbus RTU or TCP, or BACnet. Ask for the point list at the design stage so the SCADA screens can be built while the panel is being manufactured.
Related reading
- Sludge dryer feed and discharge systems
- Sludge dryer commissioning checklist
- Heat-pump sludge dryer product page