Where the margin actually accumulates
A chiller is selected through a chain: load calculation → block load → equipment selection → site correction. Margin can enter at every step, and the steps multiply rather than add.
| Step | Typical allowance | Applied by |
|---|---|---|
| Room-by-room load | 10%–20% | Consultant |
| Block load diversity | 0.85–1.00 | Consultant |
| Transmission and solar uncertainty | 5%–10% | Consultant |
| Fouling factor in the evaporator | Already in the rating | Standard |
| Altitude or ambient correction | 2%–8% | Manufacturer |
| Glycol or low-temperature derate | 8%–25% | Manufacturer |
| “Engineering margin” on the equipment | 10%–15% | Contractor |
| Spare capacity for future fit-out | 10%–20% | Client |
Multiplied out, a chain of 1.15 × 1.10 × 1.10 × 1.15 = 1.60. The 500 kW calculated load becomes an 800 kW selection, and the plant now runs at 30%–40% load in summer and 12% in spring.
Why oversizing costs more than it saves
The instinct is that spare capacity is free insurance. It is not, for four measurable reasons.
| Effect | Mechanism | Cost |
|---|---|---|
| Poor part-load COP | Screw and centrifugal efficiency falls below 40% load | 10%–20% more kWh per year |
| Short cycling | Compressor starts more than 6 times an hour | Wear, and 5%–8% efficiency loss |
| Higher capital | Larger machine, pipes, pumps, tower, electrical | 20%–35% of plant cost |
| Larger plant room | Footprint and structural load | Site cost, sometimes unbuildable |
A 800 kW screw chiller at 35% load typically runs at COP 4.2 where a 550 kW machine at 60% load runs at COP 5.4. Over 2,000 equivalent full-load hours that difference is roughly 55,000 kWh a year — about 38,000 CNY — for the privilege of owning capacity that is never used.
The allowances that must not be dropped
Cutting margin is not the same as cutting allowances. Four corrections are real physics and belong in every selection:
- Condenser water temperature. A machine rated at 30 °C entering condenser water loses 3%–4% of capacity per kelvin above it. In a tropical summer with a 32 °C tower, that is 6%–8%.
- Glycol. A 30% ethylene glycol charge cuts evaporator performance by 8%–12%; 40% cuts 12%–18%. The chiller must be rated on the actual mixture.
- Altitude. Above 1,000 m, air-cooled machines lose 3%–5% of capacity per 1,000 m, and the fan motors run hotter.
- Fouling. The rating already includes a clean-condition fouling factor. If the water is hard or the tower is dirty, the real approach temperature will be worse than the rating — that is a maintenance issue, not a reason to add another 10%.
How to apply margin once, deliberately
The cleanest method is to put all margin in one place, at the end, and state it.
Design capacity = calculated block load × 1.10
Then correct that figure for site conditions — condenser temperature, glycol, altitude — using the manufacturer’s table. Do not add a further “engineering margin” afterwards; the correction is not a margin, it is physics.
| Approach | Result on a 500 kW block load | Verdict |
|---|---|---|
| 1.10 at the end, then site correction | 550 kW → 585 kW at 32 °C condenser | Clear and defensible |
| 1.15 load, 1.10 equipment, 1.10 future | 500 → 575 → 633 → 696 kW | Compounded, wasteful |
| No margin, site correction only | 500 → 532 kW | Risky on a design day |
| Margin only as standby capacity | 2 × 300 kW, one standby | Preferred for critical loads |
Standby is not margin
These are different purchases. Margin is capacity in a single machine; standby is a second machine that can carry the load when the first fails. For a hospital, a data center or a process plant, standby is worth more than margin, and it also solves the part-load problem because two machines stage.
| Requirement | Right answer |
|---|---|
| Design day uncertainty | 10% capacity margin |
| Future fit-out in 5 years | Space and headers for a second machine, not a bigger first one |
| Critical load, no shutdown allowed | N+1 machines at 60% each |
| Load grows steadily | Modular machines added in stages |
Part-load performance is the number that predicts the bill
A chiller’s annual energy is decided between 20% and 70% load, where most machines spend most hours. Two machines with the same nominal COP can differ by 15% in annual consumption because of the shape of the curve.
| Load | Screw with slide valve | Inverter screw | Magnetic bearing centrifugal |
|---|---|---|---|
| 100% | 1.00 | 1.00 | 1.00 |
| 75% | 0.98 | 0.96 | 0.95 |
| 50% | 0.92 | 0.88 | 0.84 |
| 25% | 0.78 | 0.72 | 0.66 |
| 10% | Not stable | 0.55 | 0.48 |
The figures are relative COP against the full-load value. A plant that runs at 30% most of the year should be selected on the 25% column, not the 100% one — which is also the argument for two smaller machines rather than one large one.
What to write into the specification
Five clauses remove most of the argument later:
- State the design block load and the margin separately. “Block load 500 kW, design capacity 550 kW including 10% margin.”
- Require the capacity table. Three condenser water temperatures and the actual glycol concentration, not a single nominal figure.
- Require part-load data. COP at 100%, 75%, 50% and 25%, and the minimum stable load.
- State the fouling factor and water quality. Then the maintenance regime has a baseline.
- Define the future provision. Space, headers and electrical capacity for a named additional machine, or none at all.
A worked correction
A 550 kW selection at nominal conditions, sited where the tower delivers 32 °C condenser water, using 30% glycol, at 1,200 m altitude, with an air-cooled machine.
| Correction | Factor | Capacity |
|---|---|---|
| Nominal at 30 °C condenser water | 1.00 | 550 kW |
| Condenser water 32 °C | 0.93 | 512 kW |
| 30% ethylene glycol | 0.90 | 460 kW |
| Altitude 1,200 m (air-cooled) | 0.95 | 437 kW |
| Defrost and fouling in service | 0.97 | 424 kW |
The 550 kW machine delivers 424 kW at site conditions — 23% less than the catalog figure. If the real load is 500 kW, this selection is 15% short, and no amount of “margin” in the original number would have revealed it. The correction, not the margin, is what decides whether the plant works.
Longkang Environmental Equipment Co., Ltd. provides a capacity correction sheet with every chiller quotation listing condenser water temperature, glycol concentration and altitude, so the delivered capacity at project conditions is visible before the order rather than after commissioning. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from consultants and contractors
Is 10% margin enough?
For a load calculated from measured data with a documented diversity, yes. For a load built from area-based rules of thumb, no — fix the load calculation rather than adding margin to the equipment.
Why does the chiller short-cycle in spring?
Because the minimum stable load is above the actual load. A screw chiller may not run below 25% of nominal; if spring load is 15%, it starts and stops. Two smaller machines, or a machine with inverter control, solves it.
Can I run a chiller below its minimum load with a buffer tank?
Yes — a buffer tank of 1–2 m³ per 100 kW lets the chiller run in blocks at its minimum load and idle between them. It costs far less than a bigger machine and improves part-load efficiency.
Does a bigger chiller use more energy at full load?
Slightly less per kW of cooling, because larger machines are more efficient — but it will rarely run at full load. The annual figure is what matters.
How do I handle a client who insists on 20% spare capacity?
Ask what the spare capacity is for. If it is future fit-out, provide space and headers for a second machine. If it is design-day uncertainty, correct the load calculation and document it. Either answer costs less than an oversized machine.
What is the most common selection error you see?
Applying a glycol derate and a low-temperature derate and an altitude derate on top of a 15% margin, when only the first two are real. The machine then runs at 20% load and the client concludes that chillers are inefficient.
Related reading
- Chiller sizing and cooling load calculation
- Part-load staging for multiple chillers
- How a water chiller works
- Water chiller product page