Heat pumps · Chillers · Sludge drying systems
Knowledge

Descaling a Chiller Condenser: Diagnosis, Method and Frequency

Diagnosing fouling from the approach temperature

The measurement that matters is the approach temperature: condensing temperature minus leaving condenser water temperature. A clean condenser holds 1–2 K; a fouled one climbs.

Approach temperature Condition Action
1–2 K Clean, as commissioned None
3–4 K Light fouling, 5%–8% capacity loss Plan cleaning within 3 months
5–7 K Moderate fouling, 10%–15% loss Clean now
8–10 K Heavy fouling, 18%–25% loss Clean, inspect tubes
Above 10 K Blocked or scaled solid Clean, check for tube damage

Read the condensing temperature from the controller’s pressure transducer, not from a gauge on the refrigerant line — a gauge reads the pressure at that point, and the transducer is what the control logic uses. Convert pressure to saturated temperature using the refrigerant’s table; on R134a, 1.02 MPa absolute corresponds to about 39 °C.

The economics are simple. A 500 kW chiller with a 7 K approach instead of 2 K is doing the same cooling with a condensing temperature 5 K higher, which costs roughly 12%–15% more compressor power — about 30,000 kWh a year on 2,000 full-load hours. Cleaning the condenser is a one-day job.

What the fouling actually is

Fouling type Appearance Typical cause Removal
Scale (calcium carbonate) White, hard, adherent Hard water, high cycles of concentration Acid descaling
Biological slime Brown/green, soft Warm water, no biocide Biocide + brushing
Silt and mud Gray, loose Open tower, poor filtration Water jet, brushing
Corrosion products Rust-colored Carbon steel headers, low pH Chemical + mechanical
Hard deposits in tube ends Concrete-like Poor water treatment Mechanical reaming

Scale is the one that costs capacity quickly. Calcium carbonate has a thermal conductivity of about 2.2 W/(m·K), against 380 W/(m·K) for copper — a 0.2 mm layer adds as much thermal resistance as 34 mm of copper tube wall.

Mechanical cleaning: the first step

Mechanical cleaning removes loose deposits and is always done before any acid.

  1. Isolate and drain. Close the condenser water valves, lock out the pump, drain to a safe point. Confirm zero pressure before opening.
  2. Open the end covers. Remove the water box covers at both ends and inspect. Photograph the tube ends — this is your baseline for the next inspection.
  3. Brush the tubes. Nylon or brass brushes sized to the tube internal diameter (typically 0.8–1.0 of the tube ID), on a flexible shaft or a rod, one pass per tube. Never use a steel brush on copper-nickel tubes.
  4. Flush. Low-pressure water, 10–20 bar, from the opposite end to the brushing direction. A 100–150 bar jet is acceptable on the tube sheet but will damage tube ends if aimed at the joint.
  5. Inspect. Count blocked tubes, look for pitting and erosion at the inlet ends. More than 5% blocked tubes is a water-treatment failure, not a cleaning issue.
  6. Reassemble with new gaskets. Old gaskets leak at the first thermal cycle; keep a set on site.

Brushing removes silt and slime but not hard scale. If the tube walls still feel rough after brushing, descaling is required.

Chemical descaling: the method that works

Acid descaling dissolves calcium carbonate and restores the tube surface. Done carelessly it also dissolves the tubes.

Stage Detail Limit
Acid selection Sulfamic 5%–8%, or inhibited hydrochloric 3%–5% for steel tubes only Never HCl on stainless plates
Inhibitor Required, dosed per supplier Prevents base-metal attack
Circulation 2–4 hours at 0.5–1.5 m/s through the condenser Velocity keeps gas moving
Temperature Ambient to 40 °C Above 50 °C attack accelerates
Monitoring pH and acid strength every 30 min Stop when strength stops falling
Neutralisation Soda ash or caustic to pH 7–8 Before any discharge
Flushing Clean water until effluent pH matches supply Minimum 30 minutes
Passivation 1%–2% sodium nitrite or proprietary Optional but recommended

Three rules protect the machine. First, never circulate acid through a plate heat exchanger with stainless plates unless the supplier has approved the specific acid and concentration — chlorides cause chloride stress corrosion cracking that appears weeks later as a leak. Second, never leave acid static in the tubes; circulating or nothing. Third, always neutralise and flush before returning the condenser to service, because residual acid attacks the tubes from the water side.

Frequency: let the water decide

Water source Expected cleaning interval Basis
Municipal water, closed circuit, treated 24–36 months Low scaling potential
Cooling tower, softened make-up, biocide 12–18 months Cycles of concentration controlled
Cooling tower, hard make-up, no softener 6–12 months Scale forms within a season
River or well water, once-through 3–6 months Silt and biological load
Seawater or brackish 6–12 months, titanium tubes Corrosion more than scale

Track the approach temperature monthly and clean on trend, not on the calendar. A log that shows the approach rising from 2 K to 4 K over four months tells you the interval for that specific tower, which is more useful than any general rule.

Water treatment is cheaper than cleaning

Measure Effect Cost relative to cleaning
Softener on make-up Removes hardness, stops scale One-off, pays back in 1–2 years
Biocide dosing Stops slime and legionella Low, continuous
Side-stream filtration Removes suspended solids Moderate
Cycles of concentration control Reduces blowdown and scale Low, operational
Annual condenser cleaning Restores capacity Recurring, and stops production

A plant that cleans twice a year is a plant that has not solved its water treatment. The cleaning restores performance; the treatment is what stops the performance from falling again.

Safety, and the mistakes that damage machines

  • Never open a condenser without proving zero pressure and isolating the pump. A 300 mm valve passing under a closed isolator is a known failure mode; fit a blind if the valve does not hold.
  • Never acid-clean without an inhibitor. Plain hydrochloric acid will strip a copper tube in under an hour at 5% concentration and 40 °C.
  • Never use a steel brush or a drill-mounted wire brush on copper tubes. It removes the protective oxide layer and starts pitting.
  • Never hydro-test above the tube-side design pressure to “check for leaks” — 10 bar on a 6 bar condenser deforms the tube sheet.
  • Never reassemble with the old gaskets and expect them to seal after a thermal cycle.

Longkang Environmental Equipment Co., Ltd. supplies chillers with removable water box covers and publishes the tube count, tube diameter and design pressure in the maintenance manual, so a cleaning contractor can size brushes and plan the work without opening the machine to find out. Phone: +86 400-878-0280 | +86 130-0200-1280

Questions from maintenance teams

How do I know if the condenser needs cleaning or the machine has a refrigerant problem?

Check the approach temperature first. High condensing pressure with a normal approach points to overcharge or non-condensable gas; high condensing pressure with a high approach points to fouling. The two are distinguished by one reading.

Can I clean the condenser without shutting down?

Not properly. Tube brushing and acid circulation both require isolation. Some plants fit a spare condenser or a duplex arrangement so cleaning can be done online, but that is a design decision, not a maintenance one.

Is chemical cleaning safe for stainless steel plates?

Only with an approved acid and no chlorides. Sulfamic acid at 5% with an inhibitor is generally acceptable for 316L; hydrochloric acid is not, at any concentration, because chloride stress corrosion cracking is delayed and irreversible.

How much capacity comes back after cleaning?

Typically 10%–20% if the approach was 6–8 K, and 20%–25% if it was above 10 K. The electricity saving usually pays for the cleaning within two to four months of summer operation.

How often should the cooling tower be cleaned?

Twice a year, and the basin monthly in summer. A dirty tower sends silt straight into the condenser, which is why tower cleaning and condenser cleaning are the same maintenance task.

What is the acceptable approach temperature after cleaning?

1–2 K at design flow. If it stays above 3 K after a proper clean, the tubes may be scaled internally beyond removal, or the flow is low — check the pump and the strainer before blaming the chiller.

Related reading

Frequently asked questions