Diagnosing fouling from the approach temperature
The measurement that matters is the approach temperature: condensing temperature minus leaving condenser water temperature. A clean condenser holds 1–2 K; a fouled one climbs.
| Approach temperature | Condition | Action |
|---|---|---|
| 1–2 K | Clean, as commissioned | None |
| 3–4 K | Light fouling, 5%–8% capacity loss | Plan cleaning within 3 months |
| 5–7 K | Moderate fouling, 10%–15% loss | Clean now |
| 8–10 K | Heavy fouling, 18%–25% loss | Clean, inspect tubes |
| Above 10 K | Blocked or scaled solid | Clean, check for tube damage |
Read the condensing temperature from the controller’s pressure transducer, not from a gauge on the refrigerant line — a gauge reads the pressure at that point, and the transducer is what the control logic uses. Convert pressure to saturated temperature using the refrigerant’s table; on R134a, 1.02 MPa absolute corresponds to about 39 °C.
The economics are simple. A 500 kW chiller with a 7 K approach instead of 2 K is doing the same cooling with a condensing temperature 5 K higher, which costs roughly 12%–15% more compressor power — about 30,000 kWh a year on 2,000 full-load hours. Cleaning the condenser is a one-day job.
What the fouling actually is
| Fouling type | Appearance | Typical cause | Removal |
|---|---|---|---|
| Scale (calcium carbonate) | White, hard, adherent | Hard water, high cycles of concentration | Acid descaling |
| Biological slime | Brown/green, soft | Warm water, no biocide | Biocide + brushing |
| Silt and mud | Gray, loose | Open tower, poor filtration | Water jet, brushing |
| Corrosion products | Rust-colored | Carbon steel headers, low pH | Chemical + mechanical |
| Hard deposits in tube ends | Concrete-like | Poor water treatment | Mechanical reaming |
Scale is the one that costs capacity quickly. Calcium carbonate has a thermal conductivity of about 2.2 W/(m·K), against 380 W/(m·K) for copper — a 0.2 mm layer adds as much thermal resistance as 34 mm of copper tube wall.
Mechanical cleaning: the first step
Mechanical cleaning removes loose deposits and is always done before any acid.
- Isolate and drain. Close the condenser water valves, lock out the pump, drain to a safe point. Confirm zero pressure before opening.
- Open the end covers. Remove the water box covers at both ends and inspect. Photograph the tube ends — this is your baseline for the next inspection.
- Brush the tubes. Nylon or brass brushes sized to the tube internal diameter (typically 0.8–1.0 of the tube ID), on a flexible shaft or a rod, one pass per tube. Never use a steel brush on copper-nickel tubes.
- Flush. Low-pressure water, 10–20 bar, from the opposite end to the brushing direction. A 100–150 bar jet is acceptable on the tube sheet but will damage tube ends if aimed at the joint.
- Inspect. Count blocked tubes, look for pitting and erosion at the inlet ends. More than 5% blocked tubes is a water-treatment failure, not a cleaning issue.
- Reassemble with new gaskets. Old gaskets leak at the first thermal cycle; keep a set on site.
Brushing removes silt and slime but not hard scale. If the tube walls still feel rough after brushing, descaling is required.
Chemical descaling: the method that works
Acid descaling dissolves calcium carbonate and restores the tube surface. Done carelessly it also dissolves the tubes.
| Stage | Detail | Limit |
|---|---|---|
| Acid selection | Sulfamic 5%–8%, or inhibited hydrochloric 3%–5% for steel tubes only | Never HCl on stainless plates |
| Inhibitor | Required, dosed per supplier | Prevents base-metal attack |
| Circulation | 2–4 hours at 0.5–1.5 m/s through the condenser | Velocity keeps gas moving |
| Temperature | Ambient to 40 °C | Above 50 °C attack accelerates |
| Monitoring | pH and acid strength every 30 min | Stop when strength stops falling |
| Neutralisation | Soda ash or caustic to pH 7–8 | Before any discharge |
| Flushing | Clean water until effluent pH matches supply | Minimum 30 minutes |
| Passivation | 1%–2% sodium nitrite or proprietary | Optional but recommended |
Three rules protect the machine. First, never circulate acid through a plate heat exchanger with stainless plates unless the supplier has approved the specific acid and concentration — chlorides cause chloride stress corrosion cracking that appears weeks later as a leak. Second, never leave acid static in the tubes; circulating or nothing. Third, always neutralise and flush before returning the condenser to service, because residual acid attacks the tubes from the water side.
Frequency: let the water decide
| Water source | Expected cleaning interval | Basis |
|---|---|---|
| Municipal water, closed circuit, treated | 24–36 months | Low scaling potential |
| Cooling tower, softened make-up, biocide | 12–18 months | Cycles of concentration controlled |
| Cooling tower, hard make-up, no softener | 6–12 months | Scale forms within a season |
| River or well water, once-through | 3–6 months | Silt and biological load |
| Seawater or brackish | 6–12 months, titanium tubes | Corrosion more than scale |
Track the approach temperature monthly and clean on trend, not on the calendar. A log that shows the approach rising from 2 K to 4 K over four months tells you the interval for that specific tower, which is more useful than any general rule.
Water treatment is cheaper than cleaning
| Measure | Effect | Cost relative to cleaning |
|---|---|---|
| Softener on make-up | Removes hardness, stops scale | One-off, pays back in 1–2 years |
| Biocide dosing | Stops slime and legionella | Low, continuous |
| Side-stream filtration | Removes suspended solids | Moderate |
| Cycles of concentration control | Reduces blowdown and scale | Low, operational |
| Annual condenser cleaning | Restores capacity | Recurring, and stops production |
A plant that cleans twice a year is a plant that has not solved its water treatment. The cleaning restores performance; the treatment is what stops the performance from falling again.
Safety, and the mistakes that damage machines
- Never open a condenser without proving zero pressure and isolating the pump. A 300 mm valve passing under a closed isolator is a known failure mode; fit a blind if the valve does not hold.
- Never acid-clean without an inhibitor. Plain hydrochloric acid will strip a copper tube in under an hour at 5% concentration and 40 °C.
- Never use a steel brush or a drill-mounted wire brush on copper tubes. It removes the protective oxide layer and starts pitting.
- Never hydro-test above the tube-side design pressure to “check for leaks” — 10 bar on a 6 bar condenser deforms the tube sheet.
- Never reassemble with the old gaskets and expect them to seal after a thermal cycle.
Longkang Environmental Equipment Co., Ltd. supplies chillers with removable water box covers and publishes the tube count, tube diameter and design pressure in the maintenance manual, so a cleaning contractor can size brushes and plan the work without opening the machine to find out. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from maintenance teams
How do I know if the condenser needs cleaning or the machine has a refrigerant problem?
Check the approach temperature first. High condensing pressure with a normal approach points to overcharge or non-condensable gas; high condensing pressure with a high approach points to fouling. The two are distinguished by one reading.
Can I clean the condenser without shutting down?
Not properly. Tube brushing and acid circulation both require isolation. Some plants fit a spare condenser or a duplex arrangement so cleaning can be done online, but that is a design decision, not a maintenance one.
Is chemical cleaning safe for stainless steel plates?
Only with an approved acid and no chlorides. Sulfamic acid at 5% with an inhibitor is generally acceptable for 316L; hydrochloric acid is not, at any concentration, because chloride stress corrosion cracking is delayed and irreversible.
How much capacity comes back after cleaning?
Typically 10%–20% if the approach was 6–8 K, and 20%–25% if it was above 10 K. The electricity saving usually pays for the cleaning within two to four months of summer operation.
How often should the cooling tower be cleaned?
Twice a year, and the basin monthly in summer. A dirty tower sends silt straight into the condenser, which is why tower cleaning and condenser cleaning are the same maintenance task.
What is the acceptable approach temperature after cleaning?
1–2 K at design flow. If it stays above 3 K after a proper clean, the tubes may be scaled internally beyond removal, or the flow is low — check the pump and the strainer before blaming the chiller.
Related reading
- Chiller maintenance schedule
- Chiller high-pressure alarm causes
- Chiller water piping and insulation
- Water chiller product page