Heat pumps · Chillers · Sludge drying systems
Knowledge

Can an Air-Source Heat Pump Water Heater Work in Winter?

What the cold actually does

Two separate effects compound.

Less heat in the air. The evaporator can only absorb heat across the temperature difference between the air and the refrigerant. At −10 °C the air still contains plenty of energy, but the achievable ΔT shrinks, so the same compressor and coil move less heat.

More defrost cycles. Below about 5 °C with high humidity, moisture condenses and freezes on the coil. The unit must periodically reverse to melt it, and during defrost it takes heat from the water loop rather than adding to it.

Outdoor air Standard unit, % of nominal Cold-climate unit, % of nominal Typical COP, standard Typical COP, cold-climate
7 °C 100% 100% 4.0–4.5 4.0–4.5
0 °C 78% 88% 3.1–3.5 3.2–3.6
−7 °C 60% 80% 2.4–2.8 2.6–3.0
−15 °C Not rated 65% — 2.2–2.5
−25 °C Not rated 50% — 1.9–2.2

These are representative figures for commercial units at 45 °C outlet. Always use the manufacturer’s table for the exact model — a catalog that gives only one number at 7 °C is not enough to design with.

Why sizing is the real answer

A system sized on the annual average will fail in January. Size on the coldest design week instead:

  1. Take the daily hot water volume and the cold mains temperature in mid-winter (often 5 °C, not 15 °C).
  2. Multiply by the capacity correction for the local design air temperature from the table above.
  3. Add the morning peak factor — hotels and dormitories draw 40%–60% of daily volume in two hours.
  4. Check that the machines plus storage can cover that peak, not just the daily total.

Example. A 100-person dormitory needs 6 t/day at 55 °C. In winter, mains water at 5 °C means ΔT = 50 K, so the daily energy is 6 × 50 × 1.163 = 349 kWh, not the 279 kWh calculated at 15 °C. At a design air temperature of −7 °C, a standard unit runs at 60% of nominal, so a 40 kW nominal machine gives 24 kW — 576 kWh over 24 hours, enough in theory but with no margin for the 06:00–08:00 peak. The practical answer is either two machines, a cold-climate model, or a larger tank that lets the units run through the night on off-peak power.

What to specify for a cold site

Requirement Why it matters How to verify
Vapor-injection or two-stage compressor Keeps mass flow up at low evaporating temperature Datasheet with capacity at −15 °C, not just 7 °C
Rated operating range to −20 °C or lower Defines the legal operating envelope for warranty Nameplate and manual
Anti-frost base and condensate drain trace Ice build-up cracks the base and blocks drainage Drawing detail
Crankcase heater Prevents oil dilution on cold starts Wiring diagram
Insulated, heat-traced water pipework Frozen pipes are the most common winter failure Insulation schedule
Low-ambient fan speed control Avoids over-cooling the coil at low load Controller parameter list
Defrost on demand, not on timer Timer defrost wastes energy when the coil is clean Controller description

Making defrost work for you rather than against you

Defrost should trigger on coil temperature and pressure, not on a fixed clock. A unit that defrosts every 45 minutes regardless of conditions throws away 5%–10% of its winter output; a unit that never fully clears the coil loses far more, because ice insulates the fins and the capacity collapses.

Watch for these signs:

Symptom Likely cause Action
Defrost every 30–40 min, short cycle Humidity sensor or coil sensor drifted Recalibrate or replace sensor
Thick ice at the bottom of the coil only Drain pan blocked, water refreezes Clear the drain, add trace heat
Unit stops after defrost and restarts slowly Suction superheat set too low Adjust expansion valve setting
Ice on the fan guard Fan running during defrost Check the defrost relay and fan delay
Frequent high-pressure trips in defrost Reversing valve bypassing Inspect the four-way valve

Operating measures that recover 10%–20% in winter

  • Lower the setpoint to 50 °C in winter and use a mixing valve at the outlet. Every 5 K reduction in delivery temperature lifts COP by roughly 8%–12%.
  • Heat at night. If the site has a time-of-use tariff, let the units run through the cheap window and store the energy in the tank.
  • Keep the coil clear. Snow, leaves and stored goods against the unit cost more capacity than any control setting.
  • Do not pour hot water on the coil to clear ice. The thermal shock damages the fin-to-tube bond; use the defrost cycle or warm air.
  • Add a backup only for the peak. An electric immersion heater sized for the two coldest weeks of the year is cheaper than over-sizing the heat pump for 8,760 hours.

Frequently asked questions

Will it still produce hot water at −20 °C?

A cold-climate unit will, at roughly 40%–50% of nominal capacity and a COP near 2. A standard unit will either lock out or run at a capacity too low to be useful. If the site regularly sees −20 °C, the model selection decides the outcome.

Why does my unit stop heating in winter and show a fault?

The three common causes are low pressure from a refrigerant leak, a defrost termination sensor that never reaches its setpoint, and a low-ambient lockout that is set too conservatively in the controller. Read the fault code before touching anything — the first two need a refrigeration technician.

Does defrost really cost energy?

Yes. Each cycle takes heat from the water to melt the ice, and the compressor keeps running. Well-tuned demand defrost costs 3%–6% of winter output; timer-based defrost on a clean coil can cost twice that.

Can I keep 60 °C storage in winter?

You can, but it is expensive. Storing at 60 °C instead of 50 °C adds 10 K to every liter and raises standing losses, which together can add 15%–20% to winter consumption. Store at 50–55 °C and use a thermostatic mixing valve if the application needs 60 °C at the tap.

How big should the electric backup be?

Size it for the gap between the heat pump output at design conditions and the peak-hour demand, not for the whole load. In most Chinese and European projects that is 20%–30% of total capacity, switched by outdoor thermostat or by the controller’s auxiliary output.

Is ice on the unit ever normal?

A thin, even frost layer during operation is normal and is what defrost removes. Ice that persists after a defrost cycle, or that builds into a block at the base, is not — it means the drain or the defrost termination is faulty.

Longkang Environmental Equipment Co., Ltd. supplies both standard and cold-climate units and provides the capacity table at −7, −15 and −20 °C with each quotation, so the winter peak can be checked before the order rather than after the first cold snap. Phone: +86 400-878-0280 | +86 130-0200-1280

Related reading

Frequently asked questions