Step 1 — Build the demand from the hotel’s own operation
Do not use a single liters-per-room figure and stop there. A hotel’s hot water load comes from four streams, and the laundry and kitchen are often larger than the rooms.
| Load | Basis | Typical figure |
|---|---|---|
| Guest rooms | Per occupied room per day | 100–160 L at 60 °C |
| Laundry | Per kg of linen | 15–25 L at 60 °C |
| Kitchen | Per cover | 5–10 L at 60 °C |
| Public areas, spa, pool | Per user or per m² | Site specific |
A 120-room hotel at 75% occupancy with 120 L per room uses 10.8 m³ per day for guests. If the hotel launders 400 kg of linen a day at 20 L/kg, that is another 8 m³ — the laundry is nearly as large as the rooms, and it peaks in the morning at the same time as the showers.
| Hotel type | Rooms | Daily demand (m³ at 60 °C) | Notes |
|---|---|---|---|
| Budget / guesthouse | 40 | 3–5 | Low occupancy variance |
| Business hotel | 120 | 10–16 | Laundry often outsourced |
| Resort | 200 | 25–40 | Pool, spa, multiple restaurants |
| City 5-star | 300 | 45–70 | Laundry on site, 24-hour demand |
Step 2 — Find the peak hour, not the peak day
The peak-hour factor for a hotel is typically 10%–15% of daily demand, concentrated between 07:00 and 09:00 and again between 20:00 and 23:00. Storage has to cover the difference between that peak and what the heat pumps can produce in the same hour.
Storage (m³) = peak-hour demand − heat pump output in that hour
For 12 m³ per day, a 15% peak gives 1.8 m³ in the busiest hour. If the heat pumps deliver 0.8 m³ equivalent in that hour, storage needs at least 1.0 m³ of usable hot volume — and because stratification and blending reduce usable volume, specify about 1.5 times that.
Step 3 — Size the heat pumps on the recovery window
Hotels usually heat at night and during the low-demand periods, so the recovery window is 10–14 hours.
| Daily demand | Energy at ΔT 45 K | Heat pump capacity at 12 h | Suggested units |
|---|---|---|---|
| 5 m³ | 261 kWh | 22 kW | 1 × 25 kW |
| 10 m³ | 523 kWh | 44 kW | 2 × 25 kW |
| 20 m³ | 1,045 kWh | 87 kW | 3 × 30 kW |
| 40 m³ | 2,090 kWh | 174 kW | 4 × 45 kW |
Apply the winter ambient correction before choosing the model. A unit rated 30 kW at 20 °C may deliver 20–22 kW at −5 °C, which is the condition that matters in February.
Step 4 — Tank volume and configuration
| Hotel size | Storage | Configuration |
|---|---|---|
| Up to 60 rooms | 3–5 m³ | Two tanks in parallel, duty/standby |
| 60–150 rooms | 6–12 m³ | Three tanks, manifolded |
| 150–300 rooms | 12–25 m³ | Sectional tanks or banks of cylinders |
| Resort with spa | 25–40 m³ | Separate spa storage |
Two tanks are better than one: they allow cleaning and maintenance without shutting the hotel down, and they reduce the risk of a single stratification failure. Connect them with a balanced header, not in series, so both see the same flow.
Step 5 — Distribution and the return loop
| Item | Design value |
|---|---|
| Supply temperature | 60 °C at the tank, 55 °C at the riser |
| Return loop temperature | Above 50 °C |
| Return pump | Sized for 20%–30% of design flow |
| Pipe insulation | 40 mm on risers, 30 mm on branches |
| Blending valve | At each draw-off group, set to 45–50 °C |
| Circulation control | Timer plus thermostat, not continuous |
A hotel without a return loop wastes the first 10–20 liters at every tap and generates complaints about “waiting for hot water”. A loop with a pump running 24 hours wastes more energy than it saves; control it on return temperature.
Step 6 — Legionella and redundancy
| Measure | Setting |
|---|---|
| Storage temperature | 60 °C minimum |
| Thermal disinfection | Weekly rise to 70 °C for one hour, or continuous 60 °C |
| Dead legs | Eliminated, or flushed weekly |
| Sentinal taps | Monthly temperature check |
| Backup heating | Electric immersion or existing boiler |
Guests are a vulnerable population and hotels have been the source of outbreaks. A system that stores at 45 °C to save energy is not a design choice; it is a health risk.
Step 7 — Noise, siting and the plant room
A hotel plant room is usually adjacent to a kitchen or a plant deck below guest rooms. Air-source units produce 58–65 dB(A) at 1 m, and structure-borne noise travels further than airborne noise.
| Constraint | Measure |
|---|---|
| Unit below guest rooms | Spring isolators plus flexible pipe connectors |
| Unit on a roof near rooms | Acoustic barrier, 1.5× unit height |
| Plant room ventilation | 0.06–0.10 m³/s per kW, ducted |
| Defrost drainage | Raised base, drained away from walkways |
A worked example
A 120-room business hotel, 75% occupancy, 120 L per room, laundry outsourced, kitchen serving 300 covers a day:
| Item | Calculation | Result |
|---|---|---|
| Room demand | 90 rooms × 120 L | 10.8 m³/d |
| Kitchen demand | 300 × 8 L | 2.4 m³/d |
| Total | — | 13.2 m³/d |
| Daily energy | 13,200 × 4.186 × 45 ÷ 3,600 | 691 kWh |
| Heat pump at 10 h | 691 ÷ 10 | 69 kW |
| Winter correction | 69 ÷ 0.72 | 96 kW nominal |
| Selected units | 4 × 25 kW | 100 kW |
| Peak-hour demand | 15% of 13.2 m³ | 1.98 m³ |
| Storage | 1.98 − 0.8, ×1.5 | about 1.8 m³, specify 2 × 1.5 m³ |
The numbers are a starting point, not a substitute for the hotel’s own water meter data. A hotel with an existing system has ideal input data: twelve months of fuel bills and a flow meter.
Longkang Environmental Equipment Co., Ltd. prepares hotel schemes with the demand table, the winter correction and the tank volume stated separately, so the hotel can see which assumption drives the price. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from hotel projects
How much storage does a 200-room hotel need?
Typically 15–25 m³ for a full-service hotel with laundry, or 12–18 m³ if laundry is outsourced. The figure follows the peak-hour demand, not the room count directly.
Can the heat pumps replace the existing boiler entirely?
Usually yes for the base load, with the boiler retained as peak top-up and backup. A hybrid arrangement is often the most economic retrofit and avoids a single point of failure.
What happens in a cold snap?
Capacity falls and the boiler or immersion heater tops up. Design for the local design temperature, not the average winter, and keep the backup in working order.
Is 60 °C storage enough for a hotel?
Yes, with a blending valve at the point of use and a documented legionella regime. Some operators prefer 65 °C for additional margin; the standing loss is higher but the risk is lower.
How long does a hotel system take to install?
Four to eight weeks for a 120-room hotel, including tank replacement and riser work, if the plant room is accessible. Retrofits in an operating hotel are usually phased by wing.
Do I need a separate system for the kitchen?
Not necessarily, but the kitchen load is large and peaks at meal times. Many hotels use a dedicated pre-heat tank for the kitchen so that a busy service does not drop the temperature in the guest risers.
Related reading
- How to size an air-source heat pump water heater
- How to calculate hot water demand
- Air-source heat pump water heater product page