Heat pumps · Chillers · Sludge drying systems
Heat pump · Hot water · Heating · Cooling

Heat-Pump Frost and Defrost: What Is Normal, What Is Not, and How to Run in Winter

A frosted outdoor coil is not automatically a fault. In cold, humid weather, moisture in the air condenses and freezes on the evaporator; the unit must defrost to keep absorbing heat. The fault begins when frost does not clear, when defrost runs too often, or when ice builds up on the fan and housing.

The difference between normal and abnormal is visible and measurable. This article explains why frost forms, how the three common defrost methods work, the winter settings that protect capacity, and a diagnostic table for the field.

Examples use a 10 HP air-source heat-pump hot-water unit. Actual defrost logic varies by manufacturer; follow the unit’s service manual.

1. Why frost forms, and when it is normal

The outdoor coil operates below the dew point and often below 0 °C. Moisture condenses on the fins and freezes. The frost layer insulates the coil and blocks airflow, so heat absorption falls. The unit must reverse the cycle or bypass hot gas to melt it.

Frost is normal under these conditions:

  • Ambient 0–7 °C with relative humidity above 60–70%.
  • Frost is light, uniform and white, and clears within one defrost cycle.
  • Defrost lasts 5–15 minutes and the unit resumes heating.
  • No ice remains on the fan blades, housing or drain pan.

Frost is abnormal when it is thick, patchy or persists after defrost; when the fan is iced; when water drips and refreezes on the base; or when defrost runs every 20–30 minutes and the space temperature falls.

Condition Frost behavior Assessment
Dry, −5 °C Little or no frost Normal
Humid, 2 °C Light frost every 60–90 min Normal
Humid, 0 °C, long cycle Thick frost, slow clear Check defrost settings
Any condition Ice on fan or housing Abnormal; stop and inspect
Any condition Defrost every 20 min Abnormal; check sensor and logic

2. The three defrost methods

Reverse cycle. A four-way valve reverses the refrigerant flow, making the outdoor coil the condenser and the indoor coil the evaporator. Hot gas melts the frost. The indoor fan usually stops to avoid blowing cold air. This is the most common method for split and monobloc heat pumps.

Hot gas bypass. A solenoid bypasses hot discharge gas to the outdoor coil without reversing the full cycle. It is faster and causes less indoor temperature disturbance, but it is more complex and needs a receiver and control valves.

Demand defrost. The controller monitors coil temperature, ambient temperature, humidity and airflow, and initiates defrost only when needed. It avoids fixed-time defrost and saves energy. Time-temperature defrost is cheaper but can run when the coil is already clean, wasting heat.

The control logic matters more than the method. A unit that defrosts on a fixed 45-minute timer will run unnecessary cycles in dry weather and insufficient cycles in humid weather. Demand defrost with a coil sensor and a pressure signal is more accurate.

3. Winter settings that protect capacity

Lower the supply temperature. Each 5 K reduction in hot-water supply temperature can raise COP by 8–12%. If the building accepts 50 °C instead of 55 °C, the heat pump runs at a lower condensing temperature and defrost recovery is faster. Check the legionella plan before reducing storage temperature.

Keep the outdoor unit clear. Remove snow from the top and sides; do not block the fan. Never pour hot water on the coil: the thermal shock can crack fins and the water refreezes in the base.

Check the drain. Defrost water must drain away. A frozen drain pan causes ice to build up and the unit to defrost more often. Heat the drain line or provide a slope and a heated pad in severe climates.

Do not over-cycle. If the unit is oversized, it reaches setpoint quickly and defrosts more often. A buffer tank and a minimum run time reduce cycling.

Use the low-temperature capacity table. A standard unit’s capacity at −7 °C may be 60% of nominal; at −15 °C, 40–50%. Size for the design ambient, not the nominal rating.

4. Diagnostic table

Symptom Likely cause Check Action
Frost does not clear Defrost sensor fault, four-way valve stuck, low refrigerant Coil temperature, valve operation, pressures Repair by qualified technician
Defrost too frequent Sensor placement, humid weather, oversized unit Defrost log, run time, unit capacity Adjust logic; add buffer
Ice on fan blades Defrost water refreezing, poor drainage Drain pan, base, ambient Clear ice, heat drain
Low heating capacity Frost, low charge, compressor valve Suction pressure, superheat, current Defrost, leak test, service
High pressure alarm Scaling, low water flow, overcharge Water flow, pressure, heat exchanger Clean, adjust flow
Unit stops at −10 °C Standard model limit, low ambient protection Model curve, ambient sensor Low-temperature kit or hybrid

5. What defrost costs, and how to measure it

Defrost is not free. Reverse-cycle defrost takes heat from the water loop to melt frost, and the unit stops heating while it does so. A unit that defrosts eight times a day for eight minutes each loses about 29 kW·h of heating output: 27 kW × 8 × 8/60. If the unit delivers 270 kW·h on a winter day, that is a 10–11% capacity penalty before any standby or backup heat is counted.

At USD 0.11/kWh and 200 winter days, the electricity associated with that lost output is roughly USD 630 per unit per year. Over ten units, the cost is significant. The point is not to eliminate defrost — it is required — but to avoid unnecessary cycles and to ensure the system has enough buffer to ride through them.

Defrost pattern Cycles/day Minutes/cycle Output lost Assessment
Light frost, demand control 4–6 5–8 10–15 kW·h Normal
Humid, 2 °C 8–10 8–10 30–45 kW·h Normal but watch
Fixed timer, dry weather 12+ 10 50+ kW·h Wasteful; adjust logic
Ice build-up Continuous — Unit stops Fault; inspect

Measure, don’t guess. Record the defrost start and end time, the coil temperature before and after, the outdoor ambient and humidity, and the water supply temperature. A unit that defrosts on a fixed timer in dry weather is wasting heat; a unit that never defrosts in humid weather is accumulating ice. The log is the evidence for adjusting the parameters.

Commissioning checklist. Verify the defrost sensor is in the correct position and not affected by the fan. Confirm the four-way valve changes over fully. Check that the outdoor fan stops or slows during defrost. Confirm the drain pan slopes to the outlet and does not retain water. Test the low-ambient cut-out and the backup heat stage. Record the first three defrost cycles and compare them with the service manual.

6. Low-temperature packages: what they change

A cold-climate heat pump uses vapor injection, a larger outdoor coil, a different refrigerant charge and a crankcase heater. It can operate at −20 °C or lower, but the capacity still falls with ambient. The package does not make the unit immune to frost; it improves low-temperature operation and defrost reliability.

If the site regularly sees −10 °C or lower, specify a low-temperature model and ask for the capacity table at the design ambient. Do not accept a nominal COP at 7 °C as evidence of winter performance.

7. Common questions

Is frost on the outdoor unit normal?

Light, uniform frost that clears in one defrost cycle is normal in humid, near-freezing weather. Thick frost, ice on the fan, or frost that returns within minutes is abnormal and needs investigation.

How often should defrost run?

There is no fixed interval. Demand defrost may run every 40–90 minutes in humid weather and much less in dry weather. A fixed 20-minute cycle suggests the logic or sensor is wrong.

Can I pour hot water on the coil?

No. The thermal shock can damage fins and brazed joints, and the water refreezes in the drain. Use the unit’s defrost function or warm air, and clear the drain.

Why does the indoor fan stop during defrost?

To avoid blowing cold air into the room while the indoor coil is absorbing heat. The fan restarts after the cycle. If it does not, check the control sequence.

Does a buffer tank reduce defrost cycling?

Yes. A buffer increases the water volume and run time, so the unit does not reach setpoint and stop as quickly. It also maintains supply temperature during defrost.

When should I switch to a hybrid system?

When the heat-pump capacity at the design ambient cannot meet the load, or when electricity is expensive and gas is available. A boiler for the coldest weeks and a heat pump for the rest is often cheaper than a very large cold-climate heat pump.

Does defrost always take heat from the indoor water?

Reverse-cycle defrost does; it temporarily makes the outdoor coil the condenser and the indoor coil the evaporator, so it extracts heat from the water loop. Hot-gas bypass defrost uses compressor discharge heat and has less impact on water temperature. The choice affects comfort and efficiency, not just frost removal.

How can I tell whether demand defrost is working?

Compare the defrost frequency with the weather. In dry, cold weather it should be rare; in humid, near-freezing weather it should be more frequent but still clear the coil. If the frequency never changes, the controller may be running a fixed timer or a sensor may be stuck.

Longcom Environmental Protection Equipment Co., Ltd. can review the winter load, select low-temperature models and design defrost drainage and hybrid changeover. Send the climate data and load profile to admin@longk.com or call 400-878-0280.

Defrost intervals, capacities and temperatures are illustrative. Final settings must follow the manufacturer’s service manual and the site’s measured operating data.

Related reading

Heat-pump frost and defrost · Inverter heat-pump part-load efficiency · High-temperature heat pumps at 80 °C