Mistake 1 — Buying tonnes instead of evaporation rate
The most common error, and the root of most disputes. “10 t/day” is meaningless unless it states the moisture basis. Convert every offer to kg water per hour and the comparison becomes possible.
| Quotation says | Actually means | Evaporation |
|---|---|---|
| 10 t/day, 80% to 30% | 10 t wet cake | 7,143 kg/day = 357 kg/h over 20 h |
| 10 t/day evaporation | water only | 10,000 kg/day = 500 kg/h |
| 10 t/day dried product | 30% moisture output | 16,700 kg water/day = 835 kg/h |
Three offers that look identical are a factor of 2.3 apart. The check: convert all three to kg/h at the same inlet and outlet moisture, then compare price per kg/h.
Mistake 2 — Using the design moisture instead of a measured one
Design documents carry a moisture figure from the original commissioning of the dewatering plant, often a decade old. The sludge has changed since: different industrial dischargers, different polymer, different digester operation.
| Source of the number | Reliability | Action |
|---|---|---|
| Design report, 10 years old | Low | Test the actual cake |
| Monthly lab average | Moderate | Check the spread, not the mean |
| Daily grab samples over 2 weeks | Good | Use this for sizing |
| Continuous moisture meter | High | Use for control, not sizing |
Sample for two weeks, at different times of day, and record the maximum as well as the average. Sizing on a mean of 78% when the cake regularly reaches 84% leaves the dryer 20% short for a week at a time.
Mistake 3 — Forgetting the winter derate
A heat pump dryer rated at 500 kg/h in a 25 °C plant room evaporates about 425–450 kg/h at 5 °C, because the evaporator has to work at a lower temperature and the air holds less moisture. The nameplate does not mention it.
| Ambient in the dryer hall | Capacity factor | 500 kg/h becomes |
|---|---|---|
| 30 °C | 1.05 | 525 kg/h |
| 20 °C | 1.00 | 500 kg/h |
| 10 °C | 0.92 | 460 kg/h |
| 0 °C | 0.85 | 425 kg/h |
| −5 °C (unheated hall) | 0.78 | 390 kg/h |
The check: ask for the capacity table at 0 °C, 10 °C and 20 °C, and either heat the hall or size on the winter column. A dryer hall held at 15–20 °C is not a luxury; it is part of the machine’s rating condition.
Mistake 4 — Ignoring how sticky the sludge is
Belt dryers rely on the cake being extruded into a stable layer. Sludge with a high polymer dose, high organic content, or a high proportion of biological gel sticks to the belt, blinds the perforations and has to be scraped off by hand.
| Sludge character | Symptom | Remedy at selection |
|---|---|---|
| High polymer, gel-like | Sticks to belt, blinds perforations | Larger belt area, lower layer, belt release coating |
| Fibrous (paper, textile) | Bridges the extruder | Different extruder, wider openings |
| Sandy (dredging) | Abrades belt and screws | Wear liners, stainless belt |
| Oily (refinery, metal) | Coats the belt, slows drying | Pre-dewatering, higher temperature |
The usual design figures — 25–35 kg of water per m² of belt per hour — assume a free-draining cake. For gel-like sludge the figure falls to 15–20 kg/(m²·h), which means 40%–70% more belt area for the same evaporation. The check: send a 20 kg sample to the dryer supplier for a drying test, and ask for the belt area they calculated from it.
Mistake 5 — Sizing without heat and mass balance
A dryer is not a box that takes wet cake and produces dry cake. It needs a defined air flow, a defined temperature, and a defined heat input at the evaporator. Dryers selected on “kg/h” alone often turn out to have a heat pump that cannot deliver the latent load.
Heat required = evaporation rate × (latent heat + sensible heat to raise the water to boiling)
For 500 kg/h at 60 °C, with a latent heat of about 2,360 kJ/kg and sensible heating from 20 °C: 500 × (2,360 + 167) ÷ 3,600 = 351 kW of heat. At a heat pump COP of 3.0, that is 117 kW of electrical input, before fans and pumps. If the quotation shows a 55 kW heat pump for a 500 kg/h machine, the evaporation figure is wrong or the COP claim is.
Mistake 6 — No feed buffer
Sludge arrives in batches: a centrifuge discharges a cake every few minutes, a truck delivers 20 tonnes at once, a shift produces more than the next. A dryer fed directly from the dewatering machine runs at varying load and varying moisture, and the control cannot hold the outlet moisture.
The check: provide a feed hopper with at least 2–4 hours of capacity, with a level sensor and a variable-speed feed. It costs 3%–5% of the plant and removes most of the outlet moisture variation.
Mistake 7 — Forgetting the condensate
A heat pump dryer condenses the evaporated water and has to send it somewhere. For 500 kg/h evaporation, that is 0.5 m³/h of condensate carrying ammonia, volatile fatty acids and fines.
| Parameter | Typical value | Consequence |
|---|---|---|
| Condensate flow | 0.5 m³/h per 500 kg/h evaporation | Sizing of the return pump |
| Ammonia | 200–1,500 mg/L | Corrosion, odor, load on the WWTP |
| COD | 500–3,000 mg/L | Cannot go to surface water |
| pH | 7.5–9.0 | Needs neutralisation before discharge |
| Temperature | 35–45 °C | Cooling if discharged |
The condensate normally returns to the head of the treatment works. If the works cannot take that load, the project needs a treatment step, and that cost belongs in the comparison at the quotation stage, not in the variation order afterwards.
Mistake 8 — Assuming the outlet moisture is 30%
The outlet moisture is set by the disposal route, not by the dryer’s capability.
| Disposal route | Moisture requirement | Dryer duty |
|---|---|---|
| Landfill | Below 60% in many jurisdictions | Halve the water, moderate duty |
| Cement kiln co-processing | 20%–30% | Full drying |
| Incineration | Below 40% for autothermal | Full drying |
| Landscaping / compost | 40%–50% | Partial drying |
| Drying to 10% for volume reduction | 10% | High duty, higher cost |
Specifying 30% when the route only requires 60% doubles the energy and the capital. The check: confirm the disposal contract before the dryer is sized.
Mistake 9 — Underestimating corrosion
Sludge drying is a corrosive duty. Hydrogen sulfide, ammonia, chlorides and wet-dry cycling attack carbon steel within two years.
| Component | Standard material | Where it fails |
|---|---|---|
| Belt | 304 stainless | Chloride pitting above 200 mg/L |
| Heat exchanger coil | Aluminum fins, copper tubes | Ammonia and H₂S attack the fins |
| Cabinet and frame | Coated carbon steel | Condensate runs and cut edges |
| Fan and impeller | Coated steel | Wet air with fines |
| Condensate tank | Carbon steel | Internal corrosion within a year |
Specify 316L for the belt and wetted parts where chlorides are present, coated coils or an epoxy-coated coil block, and a plastic or FRP condensate tank. The premium is 8%–15% of the machine and it decides whether the plant is still running in year eight.
Mistake 10 — Buying without a performance guarantee tied to measurements
A guarantee that says “designed to evaporate 500 kg/h” is not enforceable. One that says “at 80% inlet and 30% outlet moisture, with the sludge sampled on date X, the unit will deliver 500 kg/h ±5% at 20 °C ambient” can be tested.
| Clause | What it should state |
|---|---|
| Capacity | kg water/h at stated inlet and outlet moisture |
| Conditions | Ambient temperature, sludge sample reference |
| Measurement | Feed mass, outlet mass, moisture by oven method |
| Test period | 8 hours continuous after stabilisation |
| Remedy | Additional belt area, additional heat pump, or price reduction |
The pre-order checklist
| Item | Evidence | Owner |
|---|---|---|
| Inlet moisture, mean and maximum | Two weeks of daily samples | Client |
| Outlet moisture required | Disposal contract | Client |
| Evaporation rate in kg/h | Calculation | Designer |
| Belt area at the sludge’s specific rate | Supplier’s drying test | Supplier |
| Winter capacity at hall temperature | Capacity table at 0/10/20 °C | Supplier |
| Heat balance and installed power | Calculation with heat pump COP | Supplier |
| Condensate flow and quality | Design basis | Designer |
| Materials for chloride and ammonia | Material schedule | Supplier |
| Feed buffer and discharge | Layout drawing | Designer |
| Performance guarantee wording | Contract | All |
Longkang Environmental Equipment Co., Ltd. runs a drying test on a customer sample before quoting belt area, and states capacity at 0 °C, 10 °C and 20 °C hall temperature with the moisture basis written into the offer. Phone: +86 400-878-0280 | +86 130-0200-1280
Questions from project teams
Can I dry to 10% moisture with a heat pump dryer?
Yes, but the last 10 K of moisture is slow and expensive: removing water from 20% to 10% takes about as much energy as from 60% to 40%, because the drying rate falls as the surface water disappears. Check whether the disposal route really needs 10%.
How much belt area do I need per tonne of water?
At a specific rate of 25–35 kg/(m²·h), one tonne per hour needs 29–40 m² of belt. For gel-like sludge at 15–20 kg/(m²·h), it needs 50–67 m². That is the single largest cost difference between two quotations for the same duty.
Does the dryer work at 2,000 m altitude?
It works but delivers less: the air is thinner, so each cubic meter carries less water and the fan delivers less mass flow. Allow a 8%–12% capacity reduction at 2,000 m and check the fan motor derating.
What happens if the feed stops?
The belt keeps running and the temperature rises; most controllers handle this by reducing heat input and recirculating. What damages the machine is a stop with wet cake sitting on the belt for a shift — it sets like concrete and has to be chipped off.
Is a batch cabinet better for a small plant?
Under about 150 kg/h evaporation, yes. It tolerates variable sludge, needs no extruder, and can be loaded once a shift. Above that, labor and footprint make the continuous belt cheaper to own.
How many days should be allowed for commissioning?
Five to ten days for a continuous belt dryer: mechanical checks, heat pump charging, establishing the belt speed and temperature recipe for the site’s sludge, and an 8-hour performance test. Rushing this is how a dryer ends up running at 70% of its rated evaporation for its whole life.
Related reading
- Sludge throughput and evaporation calculation
- Sludge dryer product series overview
- Why a sludge dryer falls short of capacity
- Sludge dryer product page