Step 1 — Establish the dry solids load
Wet sludge is reported as tonnage at a moisture content. The invariant quantity is the dry solids:
Dry solids (t/d) = wet tonnage × (1 − inlet moisture)
Ten tonnes per day at 80% moisture contains 2 tonnes of dry solids and 8 tonnes of water. Whatever the dryer does downstream, those 2 tonnes of solids remain — which is why moisture content, not tonnage, is the number that actually matters.
Step 2 — Set the outlet moisture from the disposal route
| Disposal route | Typical outlet moisture | Set by |
|---|---|---|
| Landfill | Around 60% | Landfill acceptance criteria |
| Co-incineration | 30%–45% | Incinerator heat balance and feed spec |
| Cement kiln co-processing | 20%–35% | Kiln feed limits |
| Brick making | 20%–30% | Forming and firing requirements |
| Agricultural / composting | 40%–60% | Standard and local rules |
Designing to 10% when the receiving facility accepts 40% wastes capital and energy on the last few percentage points, where drying cost per tonne rises steeply.
Step 3 — Calculate the water to be evaporated
Product mass = dry solids ÷ (1 − outlet moisture) Water evaporated = wet tonnage − product mass
For 10 t/d at 80% inlet to 30% outlet: product = 2 ÷ 0.7 = 2.86 t, so 7.14 t of water must be removed each day. That single number drives the entire equipment selection.
Step 4 — Convert to an hourly evaporation rate
Evaporation rate (kg/h) = water evaporated (kg/d) ÷ operating hours (h/d)
The same daily duty spread over 8 hours needs three times the hourly capacity of a 24-hour operation.
| Operating pattern | Hours per day | Capacity implication |
|---|---|---|
| Single shift | 8 | Highest hourly capacity, largest equipment |
| Two shifts | 16 | Balanced |
| Continuous | 20–24 | Smallest unit, most efficient use of capital |
Sludge output from a wastewater plant is usually continuous, so a continuous line running 20–24 hours is normally the most economical configuration. Batch drying suits small plants or sites where sludge is delivered intermittently.
Step 5 — Estimate energy demand
A heat-pump dryer removes roughly 2.5–4 kg of water per kWh of electricity under good conditions. Using 3 kg/kWh as a mid-range assumption:
Electricity (kWh/d) = water evaporated (kg/d) ÷ 3
For 7,140 kg of water: about 2,380 kWh per day, or 149 kW of average electrical demand over 16 hours.
| Specific consumption | Water removed per kWh | Consequence |
|---|---|---|
| 2.0 kg/kWh | 0.50 kWh per kg water | Poor insulation, fouled coil, high humidity |
| 3.0 kg/kWh | 0.33 kWh per kg water | Typical operating range |
| 4.0 kg/kWh | 0.25 kWh per kg water | Well-insulated new line, favorable sludge |
Compare with a conventional thermal dryer at 0.8–1.2 kg of water per kWh of fuel — the heat pump is roughly three times more efficient, which is the entire economic case for the technology.
Step 6 — Match the equipment configuration
| Configuration | Capacity range | Suited to |
|---|---|---|
| Batch cabinet dryer | 0.5–5 t/d wet | Small plants, intermittent output |
| Continuous belt dryer | 5–50 t/d wet | Municipal plants, daily output |
| Multi-belt / multi-stage | 20–100 t/d wet | Large plants, tight footprint |
| Complete line with feed and discharge | 5–100 t/d wet | Any plant wanting single-point responsibility |
Beyond the dryer itself, the line needs a feed system matched to the sludge consistency (screw conveyor for cake, piston pump for liquid sludge), a discharge system, condensate drainage and odor control.
Worked example: municipal plant, 20 t/d
| Step | Calculation | Result |
|---|---|---|
| Wet sludge | Given | 20 t/d |
| Inlet moisture | From existing dewatering | 80% |
| Dry solids | 20 × 0.2 | 4.0 t/d |
| Outlet moisture | Landfill route | 60% |
| Product mass | 4.0 ÷ 0.4 | 10.0 t/d |
| Water evaporated | 20 − 10 | 10.0 t/d |
| Operating hours | Continuous | 20 h/d |
| Evaporation rate | 10,000 ÷ 20 | 500 kg/h |
| Electricity at 3 kg/kWh | 10,000 ÷ 3 | 3,333 kWh/d |
| Average electrical demand | 3,333 ÷ 20 | 167 kW |
| Volume reduction | 1 − 10 ÷ 20 | 50% |
Note how modest the reduction is at a 60% outlet target. Going to 30% would cut the product to 5.7 t/d — a 71% reduction — but more than double the evaporation and therefore the energy. The disposal route decision is an economic decision, not an engineering preference.
Errors that cause shortfalls
| Error | Consequence | Correction |
|---|---|---|
| Sizing on wet tonnage, ignoring moisture variation | Undersized when sludge gets wetter | Size on the highest inlet moisture expected |
| Assuming catalog capacity at ideal conditions | Shortfall in humid weather | Apply the manufacturer’s correction for ambient humidity |
| Ignoring the feed system | Dryer starves or jams | Size feed and discharge to the same rate |
| No odor control allowance | Complaints, retrofit cost | Include odor treatment from the start |
| Designing to minimum moisture | Energy cost without disposal benefit | Set outlet moisture by the receiving facility |
Frequently asked questions
How do I know the actual inlet moisture content?
From the existing dewatering equipment’s operating records, or by sampling over at least two weeks. Sludge moisture varies with digester performance, polymer dose and filter press cycle time — a single spot sample is not a design basis.
Can a single dryer be re-set for a different sludge?
Yes, but capacity changes with the sludge. Fibrous sludge dries differently from oily or biological sludge, and a line specified for one type may need derating for another.
What if the sludge output varies seasonally?
Size for the peak month and accept part-load operation in the trough. Alternatively, specify two smaller lines and run one during low season.
How much space does a line need?
A 10 t/d line typically occupies 60–150 m² including feed, dryer, discharge and odor control, with height for the feed hopper. Footprint per tonne falls as capacity rises.
Is a heat-pump dryer suitable for large municipal plants?
It is used up to around 100 t/d wet with multi-belt configurations. Beyond that, thermal drying or anaerobic digestion may be more economic; the comparison should be made on total cost, not on equipment price.
What maintenance does the line need?
Coil and filter cleaning monthly to quarterly, condensate drain inspection monthly, belt or tray inspection monthly, refrigerant charge check annually, and sensor calibration annually.
Longkang Environmental Equipment Co., Ltd. sizes sludge drying lines from the mass balance outward and states the assumed inlet moisture, outlet target and specific energy consumption in the proposal. Phone: +86 400-878-0280 | +86 130-0200-1280
Related reading
- How to calculate sludge throughput
- Sludge volume reduction and drying cost
- Sludge dryer product page
- Ten sludge dryer selection mistakes
- Which sludge types a heat pump dryer can handle