Heat pumps · Chillers · Sludge drying systems
Heat pump · Hot water · Heating · Cooling

Scale in Air-Source Heat Pump Water Heaters: Diagnosis and Descaling

Water-side fouling is one of the few heat-pump problems that shows up as a slow loss of performance rather than a fault code. The unit still runs, but it runs longer, at higher condensing pressure, and the outlet temperature stops reaching setpoint. By the time the high-pressure trip appears, the exchanger may already be partly blocked.

Plate heat exchangers are efficient but sensitive to water quality. A thin scale layer raises the thermal resistance; a blocked channel raises pressure drop and reduces flow. Both push up condensing pressure and power consumption.

1. Diagnose before cleaning

Compare three signals under stable load:

  • Approach temperature. The difference between condensing temperature and outlet water temperature. A clean plate exchanger may run 2–4 K; a scaled one can rise to 6–10 K.
  • Water-side pressure drop. Compare with the commissioning record. A rising drop points to fouling or blockage.
  • Run time and current. The unit runs longer to reach the same hot-water volume, and current rises as condensing pressure climbs.

Do not diagnose on a single reading. Flow changes, air in the circuit and sensor drift can mimic fouling. Check strainers, valves and pump operation first.

2. Match the cleaning method to the fouling level

Condition Typical evidence Method Risk
Light scale Approach temperature up 2–4 K; flow normal Food-grade descaler circulated 2–4 h, then flush Over-dose can attack copper alloys
Medium scale Approach up 5–8 K; pressure drop rising Remove and soak the plate pack in a dedicated cleaner; brush if accessible Gasket damage if cleaner is too aggressive
Blocked or perforated Flow below design; repeated high-pressure trips Replace plates or the exchanger Cleaning will not restore gaps or seal

Always isolate the exchanger, depressurize, flush with clean water and neutralize before returning it to service. Follow the exchanger manufacturer’s cleaner compatibility list; a generic acid can damage brazing or gaskets.

3. Prevention is cheaper than descaling

Water hardness. High hardness means calcium and magnesium scale. A water softener or electronic conditioner at the make-up point reduces scaling, but it must be sized for the daily make-up volume, not the whole building supply. Test hardness before and after the softener monthly.

Filtration. Fit a strainer or bag filter before the heat pump and clean it on a schedule. A 0.5 mm mesh protects the plate gaps without causing excessive pressure drop; check the manufacturer’s limit.

Temperature. Scale forms faster at higher water temperature. If the application allows 50 °C instead of 55 °C, the lower setpoint reduces scaling and improves COP. Do not lower the temperature below the hygiene requirement.

Water treatment. For open cooling or hard makeup water, a water-treatment program should include hardness, alkalinity, chloride and conductivity limits. Simply adding chemicals without monitoring can create worse corrosion.

4. Maintenance that actually prevents repeat fouling

Frequency Task Record
Monthly Check strainer, water pressure, approach temperature Pressure drop, approach, setpoint
Quarterly Test hardness and conductivity; inspect softener Hardness before/after, regeneration
Annually Inspect plate pack; clean if approach has risen Before/after approach and flow
After any water work Flush and check strainer Debris found, flush volume

Keep a commissioning baseline. Without a clean baseline, “normal” drift is impossible to distinguish from fouling. Record approach temperature, pressure drop and flow at handover.

5. Warranty and water quality

Many manufacturers set a maximum hardness or chloride limit for warranty. If the local water exceeds it, pretreatment is a condition of warranty, not an optional extra. Confirm the limit in writing before order, and keep water-test records. A scaled exchanger that is attributed to untreated water can become a warranty dispute.

6. Water-quality limits to fix before tender

“Good water quality” is not a specification. The tender should state the parameters that will be measured, the limit that applies to the selected exchanger alloy, and the action if the site exceeds it. The exact numbers come from the exchanger and heat-pump manufacturers; the list below is the minimum set to request.

Parameter What to specify Test frequency
Hardness Maximum mg/L as CaCO₃ for the plate material and design temperature Monthly at the make-up point; before and after a softener.
Chloride Maximum mg/L for 316L or brazed plate; lower for copper alloys Quarterly, and after any change in water source.
Conductivity Range that matches the water-treatment program Monthly; a rising value can signal fouling or uncontrolled blowdown.
Suspended solids Particle size and concentration that the strainer can handle Quarterly; after any pipe or pump work.
pH Range compatible with the exchanger and the cleaning agent Monthly; a shift can change scale chemistry and corrosion risk.
Flow and pressure drop Design flow, minimum flow and clean pressure drop At commissioning and at every service; the trend is the earliest fouling signal.

Write the warranty condition as a measured limit, not a recommendation: “the warranty is conditional on hardness below X mg/L and chloride below Y mg/L, verified quarterly.” Then keep the test records with the service log. A scale claim without water data is difficult to defend in either direction.

7. Common questions

Can I use vinegar or a generic acid?

Not without checking the exchanger materials and gasket compatibility. A food-grade descaler is safer for light scale, but even it needs controlled concentration, time and neutralization. Strong acid can attack brazing and create leaks.

How often should a plate exchanger be cleaned?

With good water quality, inspect annually. With hard water, check the approach temperature quarterly and clean when it rises by 3–4 K above the clean baseline. Cleaning by calendar alone wastes money; cleaning too late risks blockage.

Does a softener remove all scale?

It reduces hardness, but not all fouling. Suspended solids, corrosion products and biological growth still need filtration and maintenance. Monitor hardness and pressure drop together.

Why does the unit still trip after cleaning?

Check flow, air in the circuit, sensor calibration and refrigerant charge. Cleaning removes scale but does not fix a closed valve, a worn pump or a blocked strainer. Re-check the approach temperature and pressure drop after restart.

What commissioning baseline should be recorded?

Record approach temperature, water-side pressure drop, flow, inlet and outlet temperatures and current at a stable load. A clean plate exchanger typically runs 2–4 K approach; 6–10 K indicates scale. Without the baseline, normal drift and fouling cannot be separated.

Does a water softener protect the warranty?

Only if it is specified and maintained. Many manufacturers set maximum hardness or chloride limits; where the local water exceeds them, pretreatment is a condition of warranty. Confirm the limit in writing before order and keep water-test records, or a scale claim can become a warranty dispute.

What scale risk?

Hard water deposits on the coil and raises approach. A fouled coil loses capacity and raises power. Test the water before selection.

How to treat?

Softening, filtration or chemical inhibition. Descaling needs the right acid and a neutralization plan. Do not descale a coated coil blindly.

Related reading

For product specifications, see air-source heat pump systems. For selection guides, visit the heat-pump knowledge base. Related articles: Air-Source vs Ground-Source Heat Pumps for Hot Water: When the Extra Boreholes Pay Back, Can High-Temperature Heat Pumps Replace a Steam Boiler?. To discuss a project, contact our engineering team. · Heat Pump Commissioning Checklist · Heat Pump Project Questions · Heat Pump Price Factors

Longcom Environmental Protection Equipment Co., Ltd. can review water quality, exchanger material and cleaning intervals for heat-pump hot-water projects. Send the water analysis and operating records to admin@longk.com, or call 400-878-0280.

Cleaning methods and water limits must follow the exchanger and heat-pump manufacturers’ instructions; local water chemistry and site conditions determine the actual interval.