A heat-pump selection that works at sea level can fail systematically at altitude. Above 3,000 m, air density is about 70–75% of the sea-level value. The fan still moves the same volume of air, but the mass of air — and therefore the heat it can carry — is lower. The compressor sees a lower suction pressure and a higher pressure ratio. The result is a unit that looks correctly sized on paper and delivers too little heat on site.
The fix is not simply “add 20%”. It is to select on mass flow, correct the capacity with the manufacturer’s altitude data, and adjust the freeze protection, insulation and electrical components. This article explains the three physical changes and gives a worked example for a 6 t/d hot-water project at 3,500 m.
Altitude corrections must come from the unit manufacturer or a documented calculation. The figures below are illustrative.
Common questions
What changes with altitude?
Air density falls, so mass flow and heat output fall. The compressor pressure ratio also changes. Nameplate capacity no longer applies.
How much derating?
Typically 2–3% per 300 m above 1,000 m, but verify with the manufacturer. Use the site altitude, not the city.
What compressor?
Check the compressor’s approved envelope at the site pressure. A standard unit may trip on high discharge temperature.
What defrost?
Defrost takes longer at altitude and cold. The water from defrost must drain. Ice build-up reduces capacity.
What airflow?
The fan must move more volume for the same mass. Duct and coil pressure drop rise. Check the fan curve.
What sizing?
Size on the corrected capacity at site conditions, plus a margin for defrost. Do not scale the sea-level catalog.
What control?
Set the head pressure and superheat for the site. A sea-level charge may be wrong. Commission with gauges.
What test?
Run at the site or in an altitude chamber. A sea-level test does not prove the site. Record capacity and power.
1. Three physical changes at altitude
Air density falls. At 3,000 m, atmospheric pressure is about 70 kPa and density is about 0.90 kg/m³, compared with 1.225 kg/m³ at sea level. A fan rated at 10,000 m³/h therefore moves about 9,000 kg/h at altitude, not 12,250 kg/h. The volume is the same; the mass flow is roughly 27% lower.
Heat transfer falls. The air-side heat-transfer coefficient depends on mass flow. With less mass flowing over the coil, the evaporator absorbs less heat at the same temperature difference. The compressor’s suction pressure falls, the pressure ratio rises, and both capacity and COP drop.
The boiling point falls. At 3,000 m water boils at about 90 °C; at 5,000 m, about 83 °C. A 55 °C hot-water target is still achievable, but an open tank loses more heat and cannot be used for high-temperature processes. Pressurized or closed tanks are preferable.
| Altitude | Approx. air density | Approx. boiling point | Typical capacity correction |
|---|---|---|---|
| 0 m | 1.23 kg/m³ | 100 °C | 1.00 |
| 1,500 m | 1.06 kg/m³ | 95 °C | 0.90–0.95 |
| 3,000 m | 0.90 kg/m³ | 90 °C | 0.78–0.85 |
| 4,000 m | 0.78 kg/m³ | 86 °C | 0.72–0.80 |
| 5,000 m | 0.68 kg/m³ | 83 °C | 0.65–0.75 |
The correction range is wide because it depends on the unit, refrigerant, fan curve and operating temperature. Do not use a single factor for every model.
2. Worked example: 6 t/d at 3,500 m
Input: 6,000 kg/d hot water at 55 °C, makeup water at 10 °C, a 45 K rise, 12 h heating window.
Daily heat = 6,000 × 4.187 × 45 ÷ 3,600 = 314 kW·h.
Average heat output over 12 h = 314 ÷ 12 = 26.2 kW.
At 3,500 m the manufacturer’s correction is 0.75. Required nominal capacity = 26.2 ÷ 0.75 = 34.9 kW. Select 35–40 kW nominal, not 30 kW.
Now check the air side. If the catalog gives 10,000 m³/h and the site density is 0.80 kg/m³, the mass flow is 8,000 kg/h. If the coil design needs 10,000 kg/h, the unit is 20% short on mass flow even though the volume figure looks right. The remedies are a larger coil, a higher fan speed, or a different model — not a larger compressor alone.
| Item | Value | Basis |
|---|---|---|
| Daily demand | 6.0 m³/d | 55 °C |
| Daily heat | 314 kW·h | 45 K rise |
| Average output | 26.2 kW | 12 h window |
| Altitude factor | 0.75 | 3,500 m, manufacturer data |
| Nominal selection | 35–40 kW | 26.2 ÷ 0.75 = 34.9 |
| Air mass flow | 8,000 kg/h | 10,000 m³/h × 0.80 |
3. Design changes that are not optional
Freeze protection. Night-time temperatures can fall below −15 °C even when daytime is mild. Insulate pipes to 50 mm rather than the usual 30 mm, fit heat trace on exposed lines, keep the circulation pump running below 2 °C, and place the tank indoors. For unattended sites, add a low-temperature alarm and automatic electric backup.
Insulation. Wind increases the surface heat-transfer coefficient. A tank insulated to 50 mm at sea level may need 80 mm at altitude, with a protected outer jacket. Seal every pipe joint; a small gap admits cold air and creates a local freeze point.
Electrical derating. Air is the cooling medium for breakers, contactors and variable-frequency drives. At altitude, the same current produces a higher temperature rise. Apply the manufacturer’s derating curve; a common rule is 5–10% per 1,000 m. At 3,500 m, a breaker may need 15–30% derating. Enlarge the cabinet and add filtered ventilation.
Pressure and boiling. Use a pressurized tank or a closed loop. An open tank at 3,000 m is not a problem for 55 °C, but it loses heat and is vulnerable to freezing. If the process needs 80 °C or more, a pressurized system is required.
Snow and wind. Raise the outdoor unit above the expected snow line, keep the discharge clear, and anchor the unit against wind. A drifting snow bank can block the coil for weeks.
4. Commissioning and first-season monitoring
Altitude projects are often remote, so spare parts and service visits are expensive. Commission with a load bank or the actual building load, record the mass flow, and compare the measured capacity with the corrected selection. For the first three months, log daily heat output, electricity, supply and return temperatures, defrost frequency and discharge pressure. If the measured output is more than 15% below the corrected estimate, ask the manufacturer to review the altitude correction and the control settings.
Keep a two-year spare kit on site: fan belts, sensors, filters, contactors and one set of fuses. A failed sensor that costs USD 50 in the city can cost a week of downtime at altitude.
5. Key parameters and criteria for altitude selection
Altitude correction is not one multiplier applied at the end. It changes air mass flow, heat-transfer capacity, boiling point, insulation and electrical derating at the same time. The table is a cross-check, not a substitute for the manufacturer’s altitude data.
| Parameter | Sea level | 3,000 m | 4,000 m | Field check |
|---|---|---|---|---|
| Atmospheric pressure | 101 kPa | About 70 kPa | About 62 kPa | Use the project’s altitude, not the nearest city |
| Air density ratio | 1.00 | 0.75 | 0.68 | Volume flow × site density = kg/h |
| Heating correction | 1.00 | 0.78–0.85 | 0.70–0.78 | Take the lower end when data are uncertain |
| Water boiling point | 100 °C | About 90 °C | About 87 °C | Use a pressurized or closed tank above 85 °C |
| Electrical derating | Rated current | 5–10% per 1,000 m | 5–10% per 1,000 m | Check breaker, contactor and VFD ratings |
| Insulation | 30–50 mm | 50–80 mm | 50–80 mm | Seal joints; wind raises surface loss |
The mass-flow check is independent of the capacity multiplier. A fan rated at 10,000 m³/h moves about 7,500 kg/h at 3,000 m, not 12,000 kg/h. If the coil needs 10,000 kg/h, the unit is short even when the volume figure looks correct. Ask for the coil design mass flow and compare it with the site density, not with the catalog volume.
Commissioning closes the loop. Log heat output, power, supply and return temperatures, defrost frequency and discharge pressure weekly for the first three months. When weekly heat output stays 15% or more under the corrected selection, review the altitude correction and the control settings before accepting the unit. Stock consumables for two years: drive belts, temperature sensors, filter screens and contactors. On a remote high-altitude site, a failed sensor can cost more in travel than the part itself. Longcom’s air-source heat pump page lists the low-temperature and high-altitude configurations.
Related reading
Heat Pump COP Rating · Heat Pump Commissioning Checklist · Heat Pump Project Questions