The fridge analogy is useful because it is true: a heat pump and a refrigerator use the same four components and the same refrigerant loop. The difference is which side you keep. A fridge keeps the cold side; a heat pump keeps the hot side. The charge does not create heat; it moves it.
This article follows one charge around the loop. At each step, it names the component, the state change and the reading a technician can take. It is a mental model for service, not a textbook cycle.
Start with the charge, not the diagram
A sealed charge of R410A circulates without being consumed. It changes state, pressure and temperature, but the mass is constant. The compressor is the only component that adds work. The evaporator and condenser are heat exchangers; the expansion valve is a pressure drop. If the charge is lost, the loop still runs, but the pressures and temperatures move to the wrong place.
| Step | Component | State change | Reading |
|---|---|---|---|
| Evaporation | Air coil | Liquid to vapor | Suction pressure, superheat |
| Compression | Compressor | Low vapor to high vapor | Discharge temperature, current |
| Condensation | Water exchanger | Vapor to liquid | Condensing approach, subcooling |
| Expansion | EEV | High liquid to low mixture | Valve step, liquid line temperature |
Step 1: evaporation is loading
The liquid enters the coil at a low pressure. The coil is colder than the air, so heat flows from the air to the refrigerant. The liquid boils, the vapor fraction rises, and the charge leaves the coil as a low-pressure gas with a few kelvin of superheat.
The evaporating temperature is not the air temperature. At 20 °C ambient, a normal coil runs at 2–5 °C, about 7–10 K below the air. At -5 °C ambient, it may run at -12 °C. The difference is the heat-transfer driving force. A dirty coil or a low airflow makes the coil colder for the same air, which is why a dirty coil looks like a low charge.
The superheat is the safety margin. 3–5 K means the vapor is just dry enough to protect the compressor. Below 2 K, liquid may reach the compressor. Above 10 K, the coil is starved and the last part of the coil is not doing useful work.
Step 2: compression is lifting
The compressor takes the low-pressure vapor and raises its pressure and temperature. The work is not just a pressure increase; it also raises the temperature above the water temperature, so the next step can transfer heat.
At the standard point, the suction is about 0.93 MPa and the discharge about 3.83 MPa. The ratio is 4.1, and the discharge is 75–85 °C. At a winter ratio of 7.2, the discharge rises to 95–105 °C. Above 110 °C, the oil film and the discharge valve are at risk.
The compressor does not have a fixed capacity. As the ratio rises, its volumetric efficiency falls and the mass flow falls. That is why the same unit delivers less heat in winter even though the compressor is running at full speed. The current may be lower, not higher, because the mass flow is lower; a low current is not proof of a healthy charge.
Step 3: condensation is unloading
The hot vapor enters the water-side exchanger. It first loses sensible heat, then condenses at a nearly constant temperature, then subcools a few kelvin. The water gains the heat; the charge becomes a high-pressure liquid.
The condensing temperature is set by the water temperature and the exchanger approach. At 55 °C water and a 4 K approach, the condensing temperature is about 59 °C, or 3.7 MPa on R410A. A higher approach means scale, low flow or air in the loop, not a refrigerant problem.
The subcooling is the last few kelvin before the valve. 3–8 K keeps the liquid line full and prevents flash gas at the valve. A liquid line that is warm to the touch but not close to condensing temperature is a sign of subcooling; a line that is as warm as the condensing temperature is a sign that the valve is seeing flash gas.
Step 4: expansion is the return stroke
The high-pressure liquid passes through the expansion valve. The pressure drops, the temperature drops, and the liquid partially flashes into vapor. The mixture entering the coil is cold and able to absorb heat again.
The valve is the control that keeps the loop balanced. A thermostatic valve is simple but has a narrow stable range; an electronic valve holds superheat across a wider load range. The valve does not set the capacity; it sets the feed. A valve that is too far open floods the coil; too far closed starves it.
At the valve inlet, the charge should be liquid. If the subcooling is low or the liquid line is exposed to heat, the valve sees a mixture and the mass flow falls. That is why a liquid-line insulation fault can look like a charge fault.
One charge, four transformations
The same mass passes through four transformations in a closed loop. The evaporator and condenser are both heat exchangers; one takes heat from air, the other gives it to water. The compressor and valve are the two pressure boundaries. The charge is the working fluid, not a fuel.
This is why the unit can deliver more heat than the electrical input: most of the heat comes from the air, and the compressor work adds to it. It is also why the unit cannot deliver heat without a temperature difference: the coil must be colder than the air, and the condenser must be hotter than the water.
Why the fridge analogy breaks at the edges
A fridge has a small, insulated box and a stable load. A heat pump has a large air coil, a water loop, a defrost cycle and a weather-driven load. The fridge analogy explains the loop, but it does not explain the site. A fridge does not frost in the same way, does not have a 40 K water rise, and does not need a defrost reverse cycle.
The analogy also breaks at high temperature. A fridge may run at a 40 K lift; a high-temperature heat pump may run at 80 K. The same four steps apply, but the compressor, the refrigerant and the oil are different. Do not use a domestic fridge as a selection reference for an industrial heat pump.
Boundary
This article follows a single-stage vapor-compression loop. A cascade, an absorption unit or a CO2 transcritical system has different states and different readings. The four-step logic is a service model, not a universal cycle diagram.
Common questions
Is a heat pump just a reversed fridge?
In principle, yes: the same four components and the same loop. The difference is which side is useful. A fridge keeps the cold side; a heat pump keeps the hot side.
Does the refrigerant create heat?
No. It moves heat from air to water. The compressor adds work, and that work also becomes heat, but most of the delivered heat comes from the air.
What is superheat for?
It ensures the vapor leaving the coil is dry enough to protect the compressor. 3–5 K is a common target; below 2 K risks liquid return, above 10 K starves the coil.
What is subcooling for?
It keeps the liquid line full so the expansion valve does not see flash gas. 3–8 K is normal; low subcooling can look like a charge problem.
Why does the compressor current fall in winter?
The mass flow falls as the suction specific volume rises. Lower mass flow can mean lower current even though the unit is working harder on a higher pressure ratio.
Can I use the same model for 80 °C water?
No. A single-stage unit at 80 °C is outside the normal condensing range. A high-temperature or cascade unit is needed; the four steps remain, but the hardware changes.
Why does frost appear on the outdoor coil?
Frost forms when the coil surface is below 0 °C and below the dew point, and the unit is extracting heat from humid air. Defrost reverses the cycle or stops the fan. A unit that frosts unevenly may have a refrigerant or airflow problem.
How do I use superheat and subcooling to diagnose?
High superheat with low subcooling suggests undercharge or a restriction. Low superheat with high subcooling suggests overcharge or a blocked condenser. Read both at steady conditions, then confirm with the manufacturer’s table.
Further technical reading
For the cycle in more detail, see What Is an Air-Source Heat Pump Water Heater?. For the four components, see Four Components, Four Failure Modes. For defrost, see Heat-Pump Defrost Logic. For COP, see How to Read a Heat Pump COP.
Related reading
Air-source heat-pump water heater · Four components and failure modes · Defrost logic