Heat pumps · Chillers · Sludge drying systems
Heat pump · Hot water · Heating · Cooling

Buffer Tank Sizing for Air-Source Heat Pump Hot Water: Volume, Peak Draw and Stratification

The buffer tank is the part of an air-source heat-pump hot-water system that is most often sized by habit. A contractor says 30–60% of daily demand, the tank is ordered, and the building either runs out of hot water at the evening peak or stores far more than it needs. Neither outcome is a tank-quality problem; both are a sizing-method problem.

Tank volume has to be derived from three quantities: the peak draw rate, the heat-pump output during that peak, and the acceptable temperature drop. Daily demand only sets the scale. This article gives the calculation, a worked dormitory example, a comparison table for common buildings, and the hydraulic details that determine whether the stored volume is actually usable.

Figures are illustrative and use 55 °C storage. Final sizing must use the building’s measured draw profile and the selected unit’s low-temperature capacity table.

1. Start from the peak, not the daily total

Daily demand tells you how much energy is needed. Tank volume tells you how much of that energy must be available instantly. The design peak is usually a short period — 30–120 minutes — when showers, washing or process draws coincide.

Define four inputs before any calculation:

  • Daily hot-water demand at 55 °C, in metric tons or m³.
  • Peak draw, as a percentage of daily demand and its duration.
  • Heat-pump output at the design winter ambient temperature, not the nominal rating.
  • Usable temperature band, for example 55 °C storage dropping to 45 °C before the backup heater starts.

The minimum tank volume is the peak draw minus what the heat pump can produce during the peak, divided by the usable temperature band. In practice, add 10–15% for dead volume and stratification loss.

A simple version in metric tons:

Vmin = (Epeak − EHP) × 0.86 / ΔTusable

E is energy in kW·h, and ΔT is the usable tank drawdown in K. The 0.86 converts kW·h to metric tons; it comes from 3,600 ÷ (4.18 × 1,000). If the peak needs 167 kW·h and the heat pump delivers 216 kW·h over the same period, the energy deficit is zero and the tank is a buffer for defrost and simultaneity rather than a peak supplier.

2. Worked example: 100-person dormitory

Input: 100 residents, 60 L/person/day at 55 °C, incoming water 15 °C, winter ambient 5 °C. Daily demand = 6.0 m³. Daily heat = 6,000 × 4.18 × 40 ÷ 3,600 ≈ 279 kW·h.

Peak: 60% of daily demand between 18:00 and 22:00, or 3.6 m³ over four hours. Average peak draw = 0.9 m³/h. Instantaneous shower demand can be higher, but the tank sees the average over the period.

Heat pump: two 10 HP units, nominal heating 39 kW each, winter derating to 70% gives 27 kW each, 54 kW total. Over four hours, they deliver 216 kW·h. The peak requires 3.6 m³ × 4.18 × 40 ÷ 3,600 = 167 kW·h. The units can cover the peak without storage if they start with a full tank and run continuously.

Why still use a tank? Because the units cannot instantaneously follow a shower block, and because defrost cycles interrupt output. A 3 m³ tank (50% of daily demand) stores about 35 kW·h over a 10 K usable band. That is enough to bridge defrost and draw variation. A 2 m³ tank is marginal; 4 m³ is comfortable but increases standing loss.

Item Value Basis
Daily demand 6.0 m³/d 100 × 60 L
Daily heat 279 kW·h/d 40 K rise
Peak share 60% in 4 h 3.6 m³
Heat-pump output 2 × 27 kW Winter derating 70%
Recommended tank 3.0 m³ 50% of daily demand
Usable storage ≈35 kW·h 10 K band, 90% usable

3. A starting table, not a rule

Building Daily demand Peak pattern Tank share Reason
Hotel, 100 rooms 8–12 m³ Morning and evening, 4–6 h 40–60% Continuous occupancy, moderate peak
School dormitory 10–30 m³ Two narrow blocks 50–70% High simultaneity, no daytime draw
Factory dormitory 20–40 m³ Shift change, 2–4 h 50–70% Shift-based, large simultaneous draw
Office / gym 2–8 m³ Short, high-intensity 30–50% Small daily total but sharp peak
Process / kitchen 5–20 m³ Shift-long, steady 20–40% Continuous draw, less storage needed

These shares assume the heat pump is sized for the daily load and can run during the peak. If the unit is sized only for the average and the peak is narrow, the tank share must rise. If the unit is oversized, the tank can fall, but short cycling becomes the risk.

4. Temperature band and usable volume

A tank rated at 5 m³ does not deliver 5 m³ of useful hot water. The draw stops when the outlet temperature falls below the acceptable minimum, and the bottom of the tank remains cold. A well-designed tank with a dip tube and stratification may be 85–90% usable; a poorly designed tank may be 60–70%.

Usable energy = volume × 4.18 × (storage temperature − minimum acceptable) ÷ 3,600, in kW·h. For 3 m³ and a 10 K band: 3,000 kg × 4.18 kJ/kg·K × 10 K = 125,400 kJ = 34.8 kW·h. That is equivalent to about 0.75 m³ of hot water at 55 °C, not the full nominal volume.

To store that much energy in 3 m³, the usable band would need to be about 40 K, which means drawing from 55 °C to 15 °C — not acceptable for showers. Real usable storage is much smaller than the tank’s nominal energy. Size from the energy deficit, then check the usable band.

For the dormitory, 3 m³ at a 10 K band stores about 35 kW·h, equivalent to 0.75 m³ of hot water at 55 °C. The peak is 3.6 m³, so the tank alone cannot cover it; the heat pumps must run through the peak. That is normal. The tank’s job is to buffer simultaneity and defrost, not to replace the heat-pump output.

If a larger buffer is required, raise the storage temperature with a backup heater or accept a larger tank. Do not assume the nominal volume is fully usable.

5. Stratification details that decide performance

Dip tube and diffuser. Return cold water to the bottom at low velocity. A high-velocity inlet mixes the tank and destroys stratification, reducing usable capacity by 20–30%.

Sensor placement. Put the storage temperature sensor at the top third and the backup heater sensor at the upper outlet. A single sensor at the middle reads a mixed temperature and triggers the heater too early or too late.

Draw-off point. Draw from the top, not the middle. The top layer is the hottest and most stable.

Dead volume. The cold layer at the bottom and the outlet pipework are dead volume. Allow 10–15% extra. A horizontal tank has more dead volume than a vertical tank of the same nominal volume.

Insulation. Standing loss for an uninsulated 3 m³ tank can be 2–4 kW; with 50 mm insulation it falls below 1 kW. Over a year, the difference is significant. Insulate the tank, all hot pipes and the recirculation line.

6. Five sizing mistakes

Using daily demand alone. A 30% tank may be fine for a hotel and inadequate for a school with two sharp peaks. Calculate the peak.

Using nominal heat-pump output. Winter capacity can be 60–75% of the nominal figure. Use the low-temperature table.

Assuming the full tank is usable. A 10 K band gives only about 35 kW·h in 3 m³. Check the arithmetic before promising coverage.

Ignoring defrost. Defrost interrupts output for 5–15 minutes per cycle. The tank must bridge those gaps, especially in cold humid weather.

Oversizing to avoid calculation. A tank that is too large increases standing loss, capital cost and the risk of low turnover and stagnation. Size from the peak, then verify the daily turnover.

Frequently asked questions

How do I calculate buffer tank volume?

Start from the peak draw in liters per minute, the acceptable temperature drop, and the recovery time. A common check is usable volume = peak flow × draw duration minus heat-pump output during that period. Then add dead volume and stratification margin. Confirm with the unit’s capacity table.

Why not size on tank volume alone?

Volume without usable stratification is misleading. A tank may be large but fully mixed, so hot water at the top cools quickly. Use baffles or a tall cylinder, keep inlet and outlet separated, and measure usable hot volume, not nominal liters.

Where should sensors go?

Put temperature sensors at several heights, not one at the outlet. The top sensor controls the heat pump; mid and bottom sensors show whether stratification is degrading. Sensor placement decides whether the tank is charged fully or short-cycles.

How does peak draw affect heat-pump size?

The heat pump can be smaller than the peak draw if the tank carries the difference. Size the tank for the peak, the heat pump for the daily energy and recovery window. Oversizing the heat pump to match a five-minute peak wastes capital.

How is Legionella controlled?

Store hot water above 60°C or run a periodic pasteurization cycle, keep return temperature above 50°C, and avoid dead legs. A buffer tank with a large warm zone below 45°C can grow Legionella; stratification must be managed, not accidental.

Series or parallel tanks?

Series with baffles gives better stratification for a single draw; parallel is easier for large volume but tends to mix. For heat-pump charging, a tall series arrangement usually delivers more usable hot water from the same nominal volume.

How should the tank connect to the heat pump?

Use a primary loop with a flow that matches the unit’s minimum and maximum, and a secondary loop sized to the draw. Avoid a single combined loop that lets return water bypass the tank. Balance valves and a bypass are needed for low-flow operation.

What data should be logged?

Top, mid and bottom temperatures; flow; heat-pump power; defrost state; and draw events. A week of data shows whether the tank recovers before the next peak and whether the heat pump short-cycles.

Related reading

Heat pump vs gas boiler cost · Heat-pump frost and defrost · Factory dormitory hot water