A lithium battery plant does not have one cooling load. It has three: coating and rolling at the front end, injection and winding in the middle, and formation and grading at the back. Each has a different temperature, precision and redundancy requirement. Combining them into a single “total cooling load” produces a plant that is unstable at the middle stage and unreliable at the back.
This article separates the three loads, calculates a 2 GWh line, and covers the two field issues that decide whether the system works: ±0.5 K control and dew-point protection.
The example is illustrative. Final design must use the equipment suppliers’ water-temperature, flow and pressure-drop requirements.
1. Three processes, three cooling logics
Front end: coating and rolling. The coating oven leaves the electrode at 80–90 °C; cooling rollers bring it below 40 °C before winding. The roll surface temperature affects adhesion and alignment. Rolling generates heat under high pressure, and uneven roll temperature causes thickness tolerance errors. Supply water is typically 12–18 °C, and the load fluctuates by up to 40% with line speed and width.
Middle: injection, sealing and winding. The injection room needs 20–25 °C and a dew point below −35 °C. Winding and stacking tension control is temperature-sensitive; a drift causes alignment errors. The load is small but the precision requirement is high: ±0.5 K, no frequent start–stop.
Back end: formation and grading. Formation cabinets generate 2–4 kW each, with hundreds of cabinets in a workshop. The load is continuous, 24 hours, and reliability matters more than efficiency. A 30-minute power interruption can scrap a whole batch. Use N+1 and interlock with fire and UPS systems.
| Process | Equipment | Supply temperature | Precision | Load character | Configuration |
|---|---|---|---|---|---|
| Front end | Coating cooling roll | 12–15 °C | ±1.0 K | ±40% with line speed | Independent secondary pump, wide ΔT |
| Front end | Rolling mill | 15–18 °C | ±1.0 K | Stable, high | High flow, avoid local hot spots |
| Middle | Injection and winding | 18–20 °C | ±0.5 K | Small and stable | Buffer tank + three-way valve |
| Back end | Formation and grading | 20–22 °C | ±1.0 K | Continuous 24 h | N+1, high flow at terminals |
| Auxiliary | Dry-room HVAC | 7–12 °C | ±1.0 K | Seasonal | Anti-condensation, separate loop |
2. Load calculation for a 2 GWh line
Assume six coating machines at 30 kW each, four rolling mills at 20 kW each, 60 kW for injection and winding, and 100 formation cabinets at 1.8 kW with a 0.6 simultaneity factor.
- Front end: 6 × 30 + 4 × 20 = 260 kW.
- Middle: 60 kW.
- Back end: 100 × 1.8 × 0.6 = 108 kW.
- Total: 428 kW.
- With 10% margin: 470 kW.
Install three 250 kW units: two duty and one standby, 750 kW installed. Normal operation uses two units at 500 kW, about 6% above the design load. If the front end is at full load and one unit fails, the remaining unit can carry the back end and part of the front end, but not the whole line. The owner must decide whether to shed front-end load or accept a lower line speed.
A single 470 kW chiller with no standby is cheaper, but a compressor failure stops the line. The formation workshop’s scrap cost is usually much higher than the price difference. This is why N+1 is standard.
| Item | Value | Basis |
|---|---|---|
| Front end | 260 kW | 6 × 30 + 4 × 20 |
| Middle | 60 kW | Injection and winding |
| Back end | 108 kW | 100 × 1.8 × 0.6 |
| Design load | 470 kW | 428 × 1.10 |
| Installed | 3 × 250 kW | 2 duty + 1 standby |
3. Separate loops, not one mixed loop
The three processes need different supply temperatures: 15 °C front end, 18 °C middle, 20 °C back end. If they share one loop at 15 °C, the back end is over-cooled. Every 1 K reduction in chilled-water supply temperature reduces chiller COP by about 3%, so the penalty is significant.
Use a common chiller plant at 15 °C with separate secondary loops and mixing valves. The front-end loop takes 15 °C directly; the middle and back-end loops mix return water to raise the supply temperature. This preserves the chiller efficiency while meeting the process temperatures.
Each loop needs its own pump, strainer, flow sensor and differential-pressure control. A single secondary pump serving all three processes cannot respond to the front-end fluctuation without disturbing the middle loop. Decoupling is the basis of stable temperature.
4. Achieving ±0.5 K
Precision comes from three measures working together, not from a more accurate thermostat.
Buffer tank. Size 5–10 minutes of system circulation volume, typically 3–5 m³, to absorb load steps. The tank should be insulated and connected with a diffuser to avoid mixing.
Secondary pump with variable speed. Decouple the terminal flow from the chiller flow. A constant-speed pump produces a pressure surge when a valve closes, and the temperature oscillates.
Three-way or proportional valve. Control the mixing ratio at the terminal. A two-way valve with a constant-speed pump changes the loop pressure and the flow; a three-way valve maintains flow while changing temperature.
Sensor placement matters. Install the temperature sensor in the main pipe after the mixing point, at least five pipe diameters from a bend or valve, with the probe inserted one-third to one-half of the diameter. A sensor in a branch or near a valve reads a turbulent, unrepresentative value. Record a four-hour trend to verify the ±0.5 K; a single spot reading proves nothing.
5. Dew point and condensation
The chilled-water temperature must be above the dew point of the surrounding air by at least 2 K. Otherwise pipes and equipment surfaces condense, and water dripping onto electrodes scraps the product.
At 25 °C and 60% relative humidity, the dew point is about 16.7 °C. A supply temperature of 18 °C is only 1.3 K above it, so the pipes need anti-condensation insulation. At 18.7 °C or higher, the risk falls. In a dry room at −35 °C dew point, condensation inside the room is not a concern, but the pipe where it leaves the dry room into the normal workshop is a high-risk point. Insulate that transition with a vapor barrier and seal the joints.
Check the actual room conditions, not the design setpoint. In summer, the workshop may be 30 °C and 70% RH, giving a dew point of 24 °C. A 20 °C supply line will condense. Either raise the supply temperature or increase the insulation and add a drain pan.
6. Materials and safety
The electrolyte contains lithium hexafluorophosphate. If it leaks and meets water, it forms hydrogen fluoride, which attacks copper, carbon steel and glass. Wetted parts in contact with the electrolyte or its wash water should be 316L stainless steel or fluoropolymer-lined. The machine-room floor needs a containment curb and an acid-resistant coating; wash water must be collected separately, not sent to the storm drain.
Glycol is used for freeze protection in winter. A 20% ethylene glycol solution freezes at about −9 °C; 30% at about −15 °C. Higher concentration lowers the specific heat and raises the pump flow. Select the concentration from the local extreme temperature plus 5 K, not a blanket 30%.
Insulation for 15–20 °C pipes in a humid workshop must be a closed-cell, anti-condensation material with a vapor barrier. Open-cell insulation with a poor vapor barrier absorbs water and loses its performance within a season.
Frequently asked questions
What are the three cooling loads in a lithium battery plant?
Process cooling for mixing, coating and formation equipment; dehumidification for dry rooms; and comfort HVAC. They have different temperatures, humidity limits and redundancy needs, so they should be metered and designed separately.
Why is dew point critical?
Lithium salts and electrodes react with moisture. Dry rooms typically need dew points well below −20°C, and some processes go lower. A chilled-water system alone cannot reach that; it pre-cools and dehumidifies, while a desiccant rotor finishes the job.
How precise should temperature be?
Process cooling often needs ±1°C or tighter at the equipment inlet, while comfort can be ±2°C. Precision depends on the coating or formation step. Specify at the equipment, not at the chiller outlet, and include pipe heat gain.
What redundancy is needed?
N+1 on chillers and pumps is common; dry-room dehumidification may need N+1 rotors and standby power. The battery process may require no single point of failure. Define the consequence of a stoppage before choosing redundancy.
Which refrigerant is suitable?
Choose according to capacity, efficiency and local safety rules. Flammable refrigerants require charge limits, ventilation and leak detection. For large plants, water-cooled screw or centrifugal chillers with a safer refrigerant are common.
How is condensation managed?
Cooling coils and dry-room equipment produce condensate; drain it continuously and prevent carryover into the dry room. Condensate may contain lithium salts or solvents and must be treated, not discharged.
What about battery safety?
Keep cooling water away from cells and electrical rooms, provide leak detection, and separate process cooling from comfort systems. Thermal runaway produces flammable gas; ventilation and gas detection are part of the design.
What should be metered?
Chiller power, pump power, supply and return temperatures, dew point, dry-room pressure and condensate flow. Sub-meter the three loads so efficiency and cost can be allocated.
Related reading
Lithium battery plant cooling · Pharmaceutical cleanroom chillers · Refrigerant leak detection and charging