Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

Three Chiller Compressors, Three Service Signatures

Scroll, screw and centrifugal chillers are often compared on efficiency and capacity. For the service team, the more useful comparison is the maintenance signature: what each machine asks for, how often, and what a neglected machine does first.

This article compares the three by their service profile. The selection numbers are a frame; the maintenance pattern is the decision.

Three machines, three service profiles

Type Typical capacity Service signature First sign of neglect
Scroll 10–60 kW Sealed, few moving parts, no oil analysis Fan or contactor failure, low charge
Screw 60–1,500 kW Oil circuit, slide valve, oil filter High oil temperature, filter ΔP
Centrifugal 1,000 kW+ High speed, purge, surge boundary, tube pull Purge count, surge, oil level

A scroll is the simplest: a sealed compressor, a condenser fan, an expansion valve and a controller. The service is mostly electrical and air-side. A screw adds an oil circuit with a separator, cooler, filter and slide valve. A centrifugal adds a high-speed impeller, a purge unit, a surge boundary and a much larger tube bundle. The three require different skills, different spares and different shutdown lengths.

Scroll: the electrical and air-side machine

A scroll chiller has no oil sight glass and no slide valve. The compressor is sealed; the oil is charged for life unless the circuit is opened. The service check is the capacitor, contactor, fan motor, coil and charge. A scroll that trips on overload is usually a supply, capacitor or condenser airflow problem, not a compressor problem.

The common failures are fan capacitors, contactors, reversing valves in heat-pump versions and coil fouling. A scroll does not tolerate liquid return well; a flooded evaporator or a bad charge can break a scroll in one season. The service team should check superheat and subcooling at every visit, not just the current.

Spares to keep: a capacitor, a contactor, a fan motor and a pressure switch. A compressor is a 3–7 day item; the electrical parts are same-day. For a small site, the electrical spares are the difference between a one-hour repair and a one-week outage.

Screw: the oil-circuit machine

A screw chiller is an oil-managed machine. The oil separates the rotors, seals the gaps, cools the compression and carries debris to the filter. The service signature is the oil circuit: temperature, level, filter differential and oil analysis.

Check Normal Action if off
Oil supply temperature 40–55 °C Check cooler, charge, sensor
Oil filter ΔP <0.1 MPa Change filter
Sight-glass level 1/3–2/3 Find return problem, not add oil
Oil analysis Water <200 ppm, metals low Investigate leak or wear

Oil change is not a calendar item. A clean machine in a dry site may go 5,000 hours; a wet site may need 2,000. The oil sample tells you which. A high water reading suggests a leak in the oil cooler or a humid site. High iron or copper suggests bearing or rotor wear. Refrigerant dilution lowers viscosity and can trip on low oil pressure.

The slide valve is the other service point. It should move smoothly through its full stroke; a valve that sticks will hold capacity at one point and confuse the control. Check the actuator and the position feedback at each annual service. A screw that cannot unload will start against a load and draw a high current.

Centrifugal: the high-speed machine

A centrifugal chiller is a flow machine. The impeller runs at 8,000–30,000 rpm, the purge unit removes air and moisture, and the surge boundary sets the minimum load. The service signature is the purge count, the oil level, the vibration and the tube condition.

A purge count that climbs week on week usually means air or moisture is entering through a low-pressure seal, and it precedes a loss of capacity. If the oil level drops while the purge stays normal, suspect the return line or the ejector rather than topping up. Vibration above the baseline suggests bearing wear, a deposit on the impeller or a misaligned coupling. The annual service should include a vibration reading and a tube inspection.

The tube bundle needs eddy-current testing every 3–5 years, and the tube-pull space must be clear. A mechanical room that cannot pull the bundle turns a two-day inspection into a two-week project. The service team should verify the clearance at installation, not at the first failure.

Load profile decides the mix

A plant that runs at 80–100% for most hours suits a centrifugal. A plant that swings between 30% and 100% suits a screw. A plant with a small base load and a large peak suits a screw plus a scroll, or a screw plus a small screw. The maintenance signature follows the load: a centrifugal that is forced to run at 20% will surge and wear; a screw that runs at 10% will lose efficiency but not break.

N+1 is common for hospitals and data centers. Two 50% screws plus one standby give better part-load than one 100% centrifugal and no standby. The spare machine also gives the service team a window to change oil or inspect tubes without shutting the plant.

Spares by type

Type Keep on site Lead time if not
Scroll Capacitor, contactor, fan motor, pressure switch 1–7 days
Screw Oil filter, oil sample kit, pressure switch, actuator 3–14 days
Centrifugal Purge spare, oil filter, vibration sensor, gasket set 1–4 weeks

The spare list should follow the failure history. A screw site with hard water should carry a strainer and a descaling pump before it carries a compressor. A centrifugal site with a high purge count should carry a leak-detection kit before it carries a spare impeller.

Boundary

This comparison covers the compressor package, not the whole plant. A scroll chiller with a fouled condenser, a screw with a blocked filter or a centrifugal with a high purge count all fail for system reasons. The service signature tells you where to look first, not what to replace.

Common questions

Which chiller needs the most maintenance?

A centrifugal has the most demanding service: purge, oil, vibration, tube inspection and surge control. A scroll is the simplest; a screw sits in between with an oil circuit.

Does a scroll chiller need oil changes?

A sealed scroll is usually charged for life unless the circuit is opened. If the circuit is opened, the oil and filter drier must be replaced by a qualified technician.

How often does a screw chiller need oil analysis?

Annually, or every 2,000–5,000 hours depending on the site. The sample tests water, acidity, viscosity, wear metals and refrigerant dilution.

What is a normal purge count?

A low, stable count. A rising count means air or moisture is entering, usually through a low-pressure seal. It is a leak warning before capacity falls.

When should tubes be eddy-current tested?

Every 3–5 years, or sooner if the water quality is poor or a tube leak is suspected. Keep the tube-pull space clear.

Can one type do all loads?

No. A centrifugal at 20% load may surge; a screw at 10% is inefficient but tolerant. Match the type to the load profile and use a base-load machine if needed.

Which compressor has the longest shutdown?

A centrifugal usually needs the longest repair or replacement lead time, especially for a large impeller or gear. A scroll is often swapped as a module; a screw sits between. Plan spares by type.

How do I plan spares by type?

Keep filters, sensors and contactors common. For scroll, keep a spare module; for screw, keep oil and seals; for centrifugal, plan a service contract and a lead time. Match the spare to the criticality.

Further technical reading

For selection between screw and centrifugal, see Screw versus Centrifugal Chillers. For the three types, see Piston, Scroll or Screw Chillers. For screw oil and Vi, see Screw Compressor: Rotor, Oil and Vi. For centrifugal minimum load, see Centrifugal Chiller: Head, Flow and Minimum Load.

Related reading

Screw compressor rotor and oil · Centrifugal chiller surge · Chiller expansion valves