Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

Chiller Selection: The Questions That Decide Uptime

A chiller enquiry usually starts with a capacity and a price. The answers that matter are the ones behind both: how the load was calculated, how many machines should carry it, which type fits the hours, and what the quote actually includes. These questions decide whether the plant runs at part load or fights it for fifteen years.

The numbers below are normal-condition ranges. A real project needs the design conditions, but the ranges show where the estimate is likely to be wrong.

Cooling load: why three estimates differ by 30%

Three estimators can look at the same building and produce three different loads. The difference usually comes from three choices: the area index, the diversity factor and whether fresh-air load is included. An office may use 100–130 W/m² excluding fresh air; a hotel guest area 90–120; a shopping center 150–200 with lighting and people; an electronics plant 200–350 based on equipment heat; a hospital 130–180, with the clean areas at the upper end.

Whether corridors and mechanical rooms are counted can move the total by 15%. The safe method is an hourly load calculation by orientation and floor, not one total floor area multiplied by one index. If fresh air is handled by the chiller, add 20–30% for the coil load and check the latent share.

Building Cooling index (W/m²) Note
Office 100–130 Excludes fresh air
Hotel guest area 90–120 Corridors and public areas separate
Retail 150–200 Lighting and people included
Electronics plant 200–350 Equipment heat based
Hospital 130–180 Clean areas at upper end

How many machines should carry the load

Two machines are the common starting point. If one fails, the other can usually hold 60–70% of the load. Three or more suit a plant with a wide load swing, because the staging can follow the load in steps. One large machine has the lowest first cost but stops the whole plant on a fault and runs poorly at low load.

For a hospital or a data center, N+1 is the minimum, not a luxury. The standby unit also creates a maintenance window, so oil changes and tube inspection do not require a full plant shutdown. Check the minimum output of each machine: a unit that cannot unload below 25–30% will cycle if it is left to carry a small night load.

Machine type by capacity

The type should follow the capacity and the running hours. A scroll module suits small loads and gives flexible staging. A screw covers the broad middle. A centrifugal takes the large end, where a single impeller can be more efficient than several screws.

Capacity First choice Alternative Note
Below 100 kW Scroll modules Small screw Parallel staging, flexible
100–800 kW Screw Multiple scroll Best cost balance
800–2,000 kW Screw or centrifugal Magnetic bearing Decide by running hours
Above 2,000 kW Centrifugal Magnetic bearing Single-unit efficiency

A magnetic-bearing machine can improve part-load IPLV by 20–30% over a conventional centrifugal, but it costs more than 50% extra. It pays where the plant runs long hours with a wide load swing. On a small load with short hours, the saving never covers the premium.

Air-cooled or water-cooled

Start with annual running hours. Above 3,000 hours, with a tower location and a reliable water supply, water-cooled is usually the better life-cycle choice. Below 1,500 hours, air-cooled avoids the tower, pump and water treatment. Between the two, calculate the 20-year cost rather than choosing by habit.

A water-cooled plant can be 35–40% better in annual efficiency, but it adds a tower, a condenser pump and makeup water. The site test comes first: structure, footprint, water, noise and service access. A tower with nowhere to go makes the water-cooled option irrelevant, whatever its COP.

The commercial comparison

When two quotes for the same capacity differ by a factor of two, the difference is usually scope. Align six items before comparing: chiller, chilled-water pump, condenser pump, cooling tower, installation and commissioning, and warranty. A 1,000 kW water-cooled screw quoted at CNY 680,000 for the chiller alone and CNY 1.08 million turnkey may be the same scope once the missing items are priced.

Convert both to a delivered cost per kW and list the exclusions. Transport and rigging, mechanical room modification, electrical capacity and extended warranty are the items most often added after contract. Comparing the chiller price alone is not a comparison; it is a negotiation tactic.

Start-up, acceptance and the first 72 hours

Do not shorten the 72-hour run to 24 hours. A 72-hour test covers high load, low load and a start-stop cycle; 24 hours may show only one condition. If the schedule is tight, 48 hours with one complete start-stop is the minimum, and the contract should define a restart if the machine trips twice or stays down for more than four hours.

At delivery, check three things before signing: the nameplate matches the contract, the casing is undamaged, and the nitrogen holding pressure is positive. A gauge at zero means a leak in transit; find it before acceptance, not after. At handover, the commissioning record is the baseline for the next fifteen years. Without it, no one can say whether a 38 °C condensing temperature two years later is normal or high.

Faults that repeat

A start-up trip on the upstream breaker has two common causes: the instantaneous setting is below the starting current, or the transformer is too small and the bus voltage dips enough to trip adjacent equipment. Direct-on-line motors should generally stay below 20–30% of transformer capacity; above that, use a reduced-current starter or increase capacity.

High condensing pressure is a water-side sequence: check tower flow and distribution, the water filter, the condenser tubes, then the tower approach. If the approach rises from 4 K to 7 K, the tower is losing performance; clean the fill before quoting a new tower.

Frequent cycling usually means the load is below one machine’s minimum output, the temperature differential is too tight, or a flow switch or sensor is giving a false signal. Stage machines instead of using the compressor as a step controller; frequent starts damage a compressor more than steady running.

Life and maintenance

A chiller is designed for 15–20 years. At 3,000 hours a year and proper maintenance, capacity loss at year 15 is often within 8%. At 6,000 hours a year with no water treatment, a tube can perforate in 8–10 years. The compressor design life is about 40,000–60,000 running hours.

Task Interval Criterion
Log operating data Weekly Current, pressures, temperatures
Clean filters Monthly Differential above 0.05 MPa
Clean condenser By differential 60% rise or approach above 8 K
Water test and dosing Quarterly Conductivity, pH, turbidity
Electrical and insulation Annual Insulation at least 0.5 MΩ

These five tasks catch most faults before they become failures. The intervals move with the machine type and the water quality; a hard-water site may need quarterly condenser cleaning, not annual.

Common questions

Why do cooling-load estimates differ so much?

Area index, diversity and fresh-air load are the usual causes. Corridors and mechanical rooms alone can change the total by 15%. Use an hourly calculation by orientation and floor.

How many chillers should a plant have?

Two is the common start, so one can hold 60–70% of the load. Hospitals and data centers need N+1. Three or more suit a wide load swing.

Is a magnetic-bearing chiller worth the premium?

Only where annual hours are long and the load swings widely. It can improve part-load IPLV by 20–30%, but costs over 50% more; short-hour projects rarely recover it.

Air-cooled or water-cooled?

Above 3,000 hours with a tower and water, water-cooled usually wins on life-cycle cost. Below 1,500 hours, air-cooled avoids the tower and water treatment. Between, calculate 20 years.

Why does a chiller trip the upstream breaker at start?

Two checks explain most start-up trips: the breaker instantaneous setting may sit below the inrush, or the supply transformer may be too small, so the bus voltage sags. Check the setting first, then the supply capacity.

What maintenance is essential?

Log the operating data weekly, clean filters monthly, clean the condenser by differential, test the water quarterly and check insulation annually. These five catch most faults early.

What six questions?

Load, machine count, type, cooling source, quote scope and the 72-hour test. Each changes the answer. Ask them before the quote.

How do I test uptime?

Run the plant through the design day and a failure scenario. Verify the standby starts and the alarm reaches the operator. Uptime is a test, not a promise.

Further technical reading

For type selection, see Screw versus Centrifugal Chillers. For the cooling source, see Air-Cooled vs Water-Cooled Chillers. For COP and IPLV clauses, see COP and IPLV: Write the Guarantee. For installation hold points, see Chiller Installation: Four Hold Points.

Related reading

Water chiller sizing · Selection margin mistakes · Chiller acceptance