Water chiller knowledge
Air-cooled, water-cooled, screw, centrifugal and low-temperature chillers for process cooling and central air conditioning.
Screw versus Centrifugal Chillers: Selection by Capacity and Load Profile
Choosing between screw and centrifugal chillers: capacity ranges, COP and IPLV, surge, part-load behavior, oil management and cost comparison.
Chiller Spare Parts: What to Stock, and When to Replace It
Chiller wear items, replacement intervals, recommended on-site stock by machine count, typical lead times and how much to budget for spares.
Food Processing Chiller Systems: Hygiene, Load Profile and Heat Recovery
Chiller design for food plants: process loads, glycol circuits, hygiene and washdown, redundancy, heat recovery and food-safety documentation.
Explosion-Proof Chillers for Chemical and Hazardous Areas
Selecting explosion-proof chillers: hazardous zone classification, Ex protection concepts, temperature classes, remote condensers and installation requirements.
Hotel Central Air-Conditioning: Chiller Configuration and Plant Design
Chiller plant design for hotels: load profile, chiller staging, part-load efficiency, noise, redundancy and integration with domestic hot water.
Hospital Chiller Systems: Redundancy, Isolation and Indoor Air Quality
Designing hospital chiller plants: separate comfort and critical circuits, N+1 redundancy, humidity control, emergency power and isolation for maintenance.
Case Study: Explosion-Proof Chillers for a Fine Chemical Plant
How a fine chemical plant replaced an in-zone chiller with two Ex-rated low-temperature units outside the classified area, including commissioning data and results.
Commercial Complex Chiller Plant: Diversity, Staging and Tenant Metering
Designing chiller plants for shopping malls and mixed-use complexes: load diversity, staging, primary/secondary hydraulics, tenant metering and thermal storage.
Air-Cooled versus Water-Cooled Chillers: A Full Comparison
Comparing air-cooled and water-cooled chillers on efficiency, footprint, water use, maintenance, noise and cost, with guidance for each building type.
Descaling a Chiller Condenser: Diagnosis, Method and Frequency
How to detect condenser fouling from approach temperature, clean tubes by brushing or chemical descaling, and set a frequency based on water quality.
Water Chiller Installation: Plant Room Layout and Services
Plant room layout for water chillers: rigging routes, tube pull space, clearances, ventilation, drainage, vibration isolation and electrical supply.
Chilled Water Piping and Insulation: Sizing, Layout and Testing
Chilled water pipe sizing by flow and pressure drop, layout rules, air venting, insulation thickness, vapor barrier detailing and pressure testing.
Cooling Tower Installation and Piping: Siting, Water Balance and Freeze Protection
Siting and piping a cooling tower for water-cooled chillers: clearances, approach temperature, make-up and blowdown, equalising lines and freeze protection.
Water Chiller Commissioning: Sequence, Measurements and Acceptance
Commissioning a water chiller step by step: pre-start checks, oil heater, water flow, approach temperatures, capacity verification and interlocks.
Water Chiller Maintenance Schedule and Service Plan
Preventive maintenance for water chillers: tube cleaning, water treatment, oil analysis, leak checks and the intervals that protect efficiency.
Water Chiller Fault Codes and Troubleshooting
Chiller alarms explained: high and low pressure, low evaporator temperature, flow failure, oil pressure and motor overload, with the checks that find the cause.
What Is a Water Chiller? Working Principle, Types and Selection
How a water chiller works, air-cooled versus water-cooled, screw versus centrifugal, COP and IPLV explained, plus selection criteria and maintenance intervals.
Water Chiller Product Series: A Complete Selection Overview
Chiller types by compressor, heat rejection, refrigerant and duty, with a selection matrix, model-number decoding and the rating conditions that make COP comparable.
How to Size a Water Chiller: A Complete Calculation Guide
A step-by-step water chiller sizing method: cooling load components, safety margin, ambient and glycol corrections, fouling allowance, part-load check and a worked example.
How to Calculate Chiller Cooling Load: Formulas and Worked Examples
Calculate chiller cooling load with the Q = m × c × ΔT method for process cooling, plus building loads, worked examples and the margin rules that avoid…