Heat pumps · Chillers · Sludge drying systems
Drying · Reduction · Integrated

Dewatering First: Polymer, Cake and the Dryer Bill

A dryer sales sheet often starts with the feed rate: 10 t/d, 20 t/d, 50 t/d. That number is almost meaningless without the feed moisture. Ten metric tons at 80% solids contain 2 t of dry solids; ten metric tons at 75% contain 2.5 t. The dryer’s job is to evaporate water, and the water load is set by the dewatering stage, not by the dryer.

This article explains why front-end mechanical dewatering is the cheapest way to reduce drying cost, with the mass balance, polymer dose, cake solids and energy numbers.

The mass balance

Dry solids are conserved. If the feed mass is M1 at moisture P1 and the product mass is M2 at moisture P2, then M1(1−P1) = M2(1−P2). The product mass is M2 = M1(1−P1)/(1−P2). The water evaporated is M1 − M2.

For 10 t/d at 80% moisture to 30%: dry solids = 10 × 0.20 = 2 t/d. Product = 2 ÷ 0.70 = 2.86 t/d. Water evaporated = 7.14 t/d. The mass reduction is 71.4%.

Now dewater the same 2 t of dry solids to 75% before the dryer. The feed becomes 2 ÷ 0.25 = 8 t/d. The dryer still produces 2.86 t/d at 30%, but it only evaporates 8 − 2.86 = 5.14 t/d. That is 28% less evaporation for the same product.

Case Feed Dry solids Evaporation
80% to 30% 10.0 t/d 2.0 t/d 7.14 t/d
75% to 30% 8.0 t/d 2.0 t/d 5.14 t/d
70% to 30% 6.67 t/d 2.0 t/d 3.81 t/d
80% to 20% 10.0 t/d 2.0 t/d 7.50 t/d

The energy consequence

A low-temperature heat-pump dryer uses about 0.25–0.45 kWh per kg of water evaporated. At 0.35 kWh/kg, 7.14 t/d costs 2,500 kWh/d; 5.14 t/d costs 1,800 kWh/d. At CNY 0.70/kWh, that is CNY 1,750 versus CNY 1,260 per day. Over 300 days, the difference is CNY 147,000 a year, before the smaller feed pump and conveyor energy.

The dewatering stage also has a cost: polymer, power, wash water and cake disposal. The comparison should be the total cost per metric ton of dry solids, not the dryer’s electricity bill alone. A belt press with a cheap polymer may produce a 20% cake; a filter press with a higher dose may produce 30%. The extra polymer can be cheaper than the extra evaporation.

Dewatering Cake solids Polymer dose Best fit
Belt filter press 18–22% 2–4 kg/t DS Municipal sludge, large flow
Centrifuge 22–28% 3–5 kg/t DS Space-limited plant
Plate filter press 28–35% 3–6 kg/t DS High solids, batch operation
Screw press 20–30% 2–4 kg/t DS Small plant, low maintenance

Polymer is a design variable

The polymer dose is not a fixed number. It depends on the sludge’s charge, the mixing energy, the feed solids and the polymer type. A dose that is too low gives a thin cake and a cloudy filtrate; a dose that is too high gives a sticky cake that blinds the belt and increases cost. Jar tests on the actual sludge are the only reliable way to set the dose.

Measure the cake solids and the solids capture. A belt press should capture 90–95% of the feed solids; a filter press can exceed 95%. If the capture is low, the filtrate returns to the treatment plant and the load comes back as extra sludge. The dewatering stage is not a disposal step; it is a separation step.

Why not dry the dilute sludge directly?

Evaporating water from a 95%–99% sludge is expensive. The dryer must handle a large water load, the feed pump is larger, and the sludge may boil or foam. Mechanical dewatering removes water at a much lower cost per metric ton. The dryer should be the second stage, not the first.

There is a limit. A very high polymer dose can make the cake plastic and difficult to convey. A sludge with a high organic content may not dewater below 25% solids with a belt press. The design should test the actual sludge, not assume a catalog cake.

Economics

At a combined transport and disposal cost of CNY 400/t, reducing the dryer feed from 10 t/d to 8 t/d saves CNY 800/d on the feed, but the product is the same 2.86 t/d, so the disposal saving is on the front end, not the product. The real saving is the evaporation energy and the smaller dryer. A 28% lower evaporation load can reduce the dryer size by one equipment step.

Calculate the annual cost of polymer, power, wash water and cake transport, and compare it with the annual saving in dryer electricity and capacity. The cheapest dryer is often the one with the best dewatering upstream.

The dryer should be sized for the worst cake the dewatering plant can produce, not the best. A belt press that reaches 22% on a good day may deliver 18% on a rainy day with a different polymer. Use the 80th-percentile cake moisture for the dryer design and keep the dewatering performance in the operating log.

Boundary

This calculation is for a plant that can change the dewatering set-point. If the existing belt press is already at its limit, a new filter press may be needed. If the sludge is hazardous or high in salt, the cake may need washing before drying; the water balance then includes the wash water. Test the actual sludge before committing to a cake solids target.

Common questions

Why does front-end dewatering matter?

The dryer evaporates water, not solids. Dewatering from 80% to 75% moisture cuts the evaporation load by 28% for the same dry solids, reducing dryer size and energy.

How much energy does evaporation take?

A heat-pump dryer uses about 0.25–0.45 kWh per kg of water. At 0.35 kWh/kg, 7.14 t/d of evaporation is 2,500 kWh/d; 5.14 t/d is 1,800 kWh/d.

What cake solids can a belt press reach?

Typically 18–22% for municipal sludge, with 90–95% solids capture. A plate filter press can reach 28–35%, at a higher polymer dose and a batch cycle.

How do I set the polymer dose?

By jar test on the actual sludge. Dose depends on charge, mixing energy and feed solids. Too little gives a cloudy filtrate; too much gives a sticky cake and higher cost.

Can a dryer take 95% sludge directly?

It can, but the water load is very large and the energy cost is high. Mechanical dewatering is the cheaper first stage. The dryer should handle the cake, not the raw sludge.

What if the existing dewatering cannot improve?

Then the dryer must be sized for the actual cake. A new filter press may be justified by the energy saving, but test the sludge first; not every sludge responds to a higher polymer dose.

How does cake solids change the bill?

The dryer evaporates water, not solids. Raising cake solids from 20% to 25% cuts the water to evaporate by about 28%. The dryer, the boiler and the power bill all shrink.

What polymer dose?

Use the jar test and the full-scale dewatering trial. More polymer can raise solids, but the cost and the cake handling change. Optimize the total, not the dryness alone.

Further technical reading

For municipal sludge drying, see Municipal Sludge Low-Temperature Drying. For filter presses, see Filter Press and Low-Temperature Drying. For specific energy, see Sludge Dryer Specific Energy. For capacity shortfall, see Sludge Dryer Capacity Shortfall.

Related reading

Specific energy per metric ton · Sludge dryer energy cost · Sludge dryer sizing