The installation drawing often shows the dryer, the feed conveyor and the odor duct. The condensate drain is a line at the bottom with a note. That line can stop the commissioning, because a 30 t/d dryer removes 12–13 t/d of water, and every liter has to go somewhere.
This article covers the condensate route: quantity, quality, pipe sizing, trapping, neutralization and freeze protection. The example is 30 t/d at 60% moisture dried to 30%.
How much water
At 30 t/d and 60% moisture, the dry solids are 12 t/d. At 30% moisture, the product is 12 ÷ 0.7 = 17.14 t/d. The water removed is 30 − 17.14 = 12.86 t/d, or 536 kg/h. If the dryer runs 20 hours, the average is 643 kg/h; the peak may be 1.5 times the average, or about 1 m³/h.
The condensate is not the full water removal. Some water leaves with the product and some with the exhaust. For a closed-loop heat-pump dryer, most of the removed water condenses on the evaporator and drains out. Design the drain for 1.2–1.5 times the calculated water removal, not for a nominal “small drain”.
Quality, not just quantity
Sludge condensate is not clean water. It can carry ammonia, organic acids, chloride and fine solids. A typical municipal sludge condensate may have a pH of 4–6, COD of 1,000–3,000 mg/L and ammonia of 100–500 mg/L. Industrial sludge can be worse. Test the condensate before choosing the pipe material and the discharge route.
| Parameter | Typical range | Why it matters |
|---|---|---|
| pH | 4–6 | Acid attack on carbon steel and concrete |
| COD | 1,000–3,000 mg/L | Wastewater treatment load |
| Ammonia | 100–500 mg/L | Odor and biological toxicity |
| Chloride | 200–2,000 mg/L | Pitting of stainless steel |
| Total suspended solids | 50–500 mg/L | Drain blockage and sludge build-up |
Pipe sizing and slope
At 1 m³/h and a velocity of 0.6–1.0 m/s, a DN40 pipe is adequate. A DN50 pipe gives more margin and is easier to slope. Use a slope of at least 1% (10 mm per meter); 2% is better for solids. Avoid flat runs and negative slopes; a low point will collect sludge and block.
Keep the drain close to the evaporator. A long horizontal run under the floor is a future blockage. If the route must be long, use a collection sump and a pump, not a longer gravity line.
The trap
The drain must have a water trap to stop air and odor from entering the dryer. A trap with a 100 mm water seal is typical. The trap should be accessible for cleaning, with a removable cap and a drain plug. A dry trap is an open door for odor; check it during commissioning and after every long shutdown.
Do not connect the condensate drain directly to a sewer without an air break. Use an indirect connection to a collection sump or a floor drain with a gap. This prevents backflow and allows inspection.
Neutralization
If the pH is below 6, neutralize before discharge. A small dosing tank with a pH controller and a caustic solution is usually enough. Size the tank for at least one day of condensate, and provide mixing. A simple limestone bed can work for a small flow, but it loses effectiveness and needs replacement.
Check the site’s discharge limit. A high COD or ammonia load may require pretreatment or dilution before the biological plant. Do not assume the condensate can go to the storm drain because it is “only water”.
Sizing the sump and pump
A gravity drain is preferable, but a long route or a basement mechanical room may need a sump and a pump. Size the sump for at least 15 minutes of peak flow, or about 0.25 m³ for a 1 m³/h peak. A smaller sump will short-cycle the pump and leave sludge in the bottom.
Use a semi-open impeller or a vortex pump; a standard centrifugal pump can clog on the fines. Fit a level switch with a high-high alarm and a manual override. The pump should start at 70% level and stop at 20%, not at every small inflow. A check valve and an isolation valve make maintenance possible without draining the line.
Freeze protection
In a cold climate, the drain line can freeze after a shutdown. Insulate the pipe, keep a slope of at least 2%, and add a trace cable if the line is exposed. The trap is the first point to freeze; use a heated trap or keep it indoors. A frozen drain backs water into the dryer and trips the unit.
Commissioning the route
Before running sludge, fill the trap and test the drain with clean water. Confirm the flow, the slope and the air break. Run the dryer empty and check for condensation. Then run with sludge and measure the condensate flow and pH. Record the results; a drain that works on a cool day may fail on a humid day.
Label the drain, the trap and the neutralization tank. The operator should know which valve to close before cleaning and which line to check when the dryer reports a drain fault. A labeled route is part of the installation, not an afterthought.
Common questions
How much condensate does a sludge dryer produce?
For 30 t/d at 60% to 30%, about 12.86 t/d of water is removed. Design the drain for 1.2–1.5 times this value, because the peak flow can be higher than the average.
Can condensate go to the storm drain?
No. It can be acidic and carry COD, ammonia and chloride. Test it, neutralize if needed and discharge to the site wastewater system under an air break.
What pipe size should the drain be?
DN40 is adequate for about 1 m³/h at 0.6–1.0 m/s; DN50 gives more margin. Use a slope of at least 1%, preferably 2%, and avoid flat runs.
Why does the drain need a trap?
The trap stops air and odor from entering the dryer and keeps the condensate flowing in one direction. A dry trap can leak odor and upset the airflow.
How is the condensate neutralized?
Use a dosing tank with a pH controller and caustic solution, or a limestone bed for a small flow. Size the tank for at least one day of condensate and provide mixing.
What if the drain freezes?
Insulate the line, keep a 2% slope and add a trace cable on exposed runs. The trap is the first point to freeze; use a heated trap or keep it indoors.
What quality limit applies to sewer discharge?
No. Condensate may carry organic load, ammonia or sulfide. Route it to the sanitary sewer or a treatment system, subject to the discharge permit. Test before discharge.
What if the site has no drain?
Use a collection tank and a transfer pump, or a vacuum truck. Size the tank for a shift or a day of condensate. A dryer without a condensate route will stop within hours.
Further technical reading
For odor and condensate, see Odor and Condensate from Sludge Drying. For installation, see Heat-Pump Sludge Dryer Installation. For electrical and control, see Sludge Dryer Electrical and Control Systems. For commissioning, see Sludge Dryer Commissioning.
Related reading
Odor and condensate · Dryer site installation · Dryer commissioning