Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

What a 1,000 kW Chiller Really Costs

“How much is a 1,000 kW chiller?” cannot be answered with one number, not because suppliers are evasive, but because quotations for the same nominal capacity can differ by a factor of two. The difference comes from two sources: the equipment configuration itself, and the scope included in the quotation. The first is comparable; the second must be levelled before any comparison makes sense.

The headline: a 1,000 kW water-cooled screw chiller is roughly CNY 600,000–900,000 for the bare machine, and CNY 950,000–1.3 million delivered with auxiliaries, installation and commissioning. Where it lands depends on six cost variables and three scope items. This article separates all nine.

Start with a common coordinate: CNY per kW

Different chiller types have very different unit prices. Convert to CNY/kW before comparing. The table is a reference for standard configuration, nominal condition, excluding installation.

Type Typical capacity Equipment price (CNY/kW) 1,000 kW reference
Air-cooled modular 65–130 kW per unit 550–750 Not applicable; multiple units
Air-cooled screw 300–1,000 kW 850–1,100 CNY 850,000–1.1 million
Water-cooled screw 300–1,500 kW 600–900 CNY 600,000–900,000
Water-cooled centrifugal 800–3,000 kW 550–800 CNY 550,000–800,000
Magnetic-bearing centrifugal 500–2,000 kW 1,200–1,700 CNY 1.2–1.7 million
Low-temperature cascade 50–300 kW 2,500–4,000 Not applicable; small capacity, high unit price

This table answers the first question: why “price per unit” is meaningless. At the same 1,000 kW, air-cooled screw is about CNY 850,000, water-cooled screw CNY 600,000 and magnetic-bearing CNY 1.2 million. The difference is not “expensive or cheap”; it is what is being bought.

Unit price falls with capacity. In the same water-cooled screw series, 300 kW is about CNY 900/kW, 1,000 kW about CNY 700/kW and 1,500 kW about CNY 620/kW. Compressor, electrical control and sheet metal do not scale linearly. Two 500 kW units therefore usually cost more than one 1,000 kW unit.

Six cost blocks

The factory cost of a water-cooled screw chiller breaks down roughly as follows. The value of this table is that when a quotation is well below the lower bound, you can see which block was cut.

Block Share Price driver
Compressor 30–35% Brand and model; 15–30% between brands at the same capacity
Heat exchangers 20–25% Tube material (copper, stainless, titanium); surface margin
Electrical control and starter 10–15% Soft start or inverter; PLC brand; communication protocol
Sheet metal and frame 8–10% Plate thickness, coating, outdoor version
Refrigerant and piping 5–8% R134a vs R513A; valve brand
Assembly, test, packing 8–10% Full performance test or factory check only

Design, management, transport and tax add another 12–18%, which brings the total to 100%. The compressor is the first variable. An international-brand screw compressor can cost about 25% more than a domestic equivalent, which is about 8% at machine level. That does not mean domestic is unusable; it means the difference buys part-load efficiency, noise and overhaul interval.

The heat exchanger is the second variable and the easiest to “optimize”. If condenser and evaporator area are cut to 0.9 of the reference, cost falls by about 8%, but condensing temperature rises 2–3 K and annual electricity rises 4–6%. This is invisible on a quotation; compare the surface area and tube rows in the catalog.

Electrical control is the third variable and is strongly linked to later retrofit cost. A controller without communication costs CNY 3,000–8,000 less than one with Modbus or BACnet, but adding a gateway and reprogramming later costs three to five times that.

Three scope items

Most twofold price differences come from scope, not hardware. Write these three items into the enquiry.

Scope Common difference Effect on total
Auxiliaries Chilled-water pump, condenser pump, cooling tower, make-up set, water treatment CNY 180,000–280,000 at 1,000 kW
Installation Lifting, positioning, pipe connection, insulation, electrical wiring CNY 120,000–180,000; night or high-level work extra
Commissioning and training Unit test, system integration, 72-hour run, operator training CNY 30,000–60,000

Example: a 1,000 kW water-cooled screw project. Supplier A quotes CNY 680,000; supplier B quotes CNY 1.08 million, a difference of CNY 400,000. A supplies the chiller only, with pumps and tower by the client. B supplies a turnkey package: two chilled-water pumps, two condenser pumps, one square cooling tower, water treatment and full installation and commissioning. Completing A to the same scope gives about CNY 1.03 million. The two are actually at the same level; the earlier CNY 400,000 gap was illusory.

Four sentences in the enquiry save a round of argument: which auxiliaries are included, where the installation interface ends, how far commissioning goes, and how long the quotation remains valid.

Four hidden additions

Transport and lifting. A 1,000 kW water-cooled unit weighs about 5–7 t. Oversize or overweight transport needs a permit; city daytime restrictions may force night delivery; a 50 t mobile crane is typical. Allow CNY 15,000–40,000 depending on distance and access.

mechanical room modification. Replacing a unit in an old mechanical room often reveals mismatched foundation, load capacity, door opening and lifting hatch. Removing the old machine, rebuilding the base and widening the door can exceed CNY 50,000, and must be checked on site before quoting.

Electrical capacity. A 1,000 kW water-cooled chiller draws about 350 A; with pumps and tower the total may need an 800 kVA supply. If the existing transformer has no margin, upgrading per kVA is a real cost. It is not part of the chiller price, but it changes project economics.

Warranty. A 24-month warranty may cost 2–4% more than 12 months, which looks small until a compressor overhaul exceeds CNY 80,000. Check whether the warranty covers the compressor, labor and refrigerant.

Compare one number: delivered cost per kW

Do not compare totals. Compare delivered cost per kW after leveling the scope. Five steps: use design condition, not nominal condition; add missing auxiliaries at market price; add installation and commissioning at a typical rate; normalize warranty by adding the extension cost; divide the total by capacity.

In the example, A completed is about CNY 1.03 million, or CNY 1,030/kW. B is CNY 1.08 million, or CNY 1,080/kW. A 5% difference is normal for configuration and brand. At that point, compare compressor brand, heat-exchanger area and controls; those are meaningful.

Then look at lifecycle. A unit at CNY 700/kW and one at CNY 900/kW differ by CNY 200,000 at 1,000 kW. If the cheaper unit is 8% less efficient, at 3,000 full-load hours and CNY 0.65/kWh, a 1,000 kW cooling load at COP 5.0 draws 200 kW; 3,000 hours is 600,000 kWh; 8% is 48,000 kWh, or CNY 31,200 a year. The price gap takes about 6.4 years to recover. A chiller lasts 15–20 years, so the efficiency difference matters more than the first cost, but only if the load actually runs.

When a higher price is justified

Non-standard capacity. A 1,350 kW requirement cannot be met by a standard model; it needs a different heat exchanger or compressor configuration, and a 8–15% premium is normal.

Special material. Chemical, plating and pharmaceutical projects may need 316L stainless or titanium tubes, which cost 20–40% more than copper. This is material cost and cannot be negotiated away.

Explosion-proof or corrosion protection. Explosion-proof electricals, wiring and enclosures add 15–30%. Coastal or acid-mist sites need coating regardless.

Very short delivery. Standard lead time is 45–60 days; 25 days requires a production slot and adds 5–10%.

Three low prices deserve caution: more than 20% below the lower bound, refusal to state heat-exchanger area or compressor model, and vague commissioning and warranty clauses. Any one of these usually leads to later additions that exceed the saving.

Boundaries

The ranges are references for standard configuration and nominal condition. A real quotation depends on design capacity, fluid, installation environment and commercial terms. Prices move with copper, steel, refrigerant and exchange rates. Special equipment and fire requirements follow local codes.

Common questions

How much is a 1,000 kW chiller?

A water-cooled screw unit is CNY 600,000–900,000 bare and CNY 950,000–1.3 million delivered. Air-cooled screw is CNY 850,000–1.1 million; magnetic-bearing centrifugal CNY 1.2–1.7 million. A twofold difference at the same capacity is normal once scope is considered.

Why do two quotes differ by CNY 400,000?

Usually scope. The common differences are auxiliaries (pumps, tower), installation boundary and commissioning depth. Level the three items and the gap often falls within 10%.

How much difference between domestic and imported compressors?

About 8% at machine level, or CNY 50,000–80,000 on a 1,000 kW unit. The difference buys part-load efficiency and noise; if the plant runs most of the year below 50% load, electricity savings can recover it.

Can the cooling tower be added later?

Yes, but it must match condenser flow, approach and fan power. A mismatched tower raises condensing temperature. Adding it later usually costs 5–10% more than including it in the chiller package.

Is an inverter worth the premium?

An inverter centrifugal is 15–25% more; an inverter screw 8–12%. Above 2,500 hours a year with variable load, it usually pays back in three to five years. At continuous full load, the benefit is limited.

Does payment terms affect price?

Yes. 30% advance, 60% before shipment and 10% after acceptance is common. If payment is three months after delivery, suppliers may add 2–4% for capital cost. Normalize payment terms before comparing.

Why does delivered cost vary so much?

Scope, refrigerant, materials, controls, freight, installation, commissioning and warranty differ. A bare chiller price excludes the tower, pumps, piping, electrical work and water treatment. Compare the same scope and the same duty.

When is a cheaper chiller the right choice?

When the duty is stable, the hours are low and the plant has redundancy. A cheaper unit with a poorer part-load curve can cost more over ten years. Check the part-load data and the service network before deciding.

Related reading

Related reading

Water chiller sizing · Selection margin mistakes · Imported vs domestic chillers