Surge is specific to centrifugal chillers. The machine emits a low, periodic rumble; the body vibrates; current swings; in severe cases the vane actuator is shaken loose. The first reaction is often “the compressor is damaged”, but in most cases the machine is intact — the operating point has simply moved into the surge zone.
The key question is why the operating point moved. Low cooling load, high condensing pressure and incorrect refrigerant charge can all push the point toward the surge line. The remedies differ, and some are opposite. Diagnose before adjusting.
1. Confirm it is surge, not a mechanical fault
Three checks separate surge from a bearing or rotor problem.
Load test. Raise the load above 60%. If the rumble disappears, it is surge. If the noise continues and worsens independently of load, investigate the mechanical train.
Current pattern. Surge produces a periodic current swing. A bearing fault usually gives a steady high current with noise that does not pulse.
Discharge temperature. During surge, discharge temperature oscillates as flow reverses and re-establishes. A mechanical fault tends to run continuously hot.
2. Why surge happens
A centrifugal compressor accelerates gas in the impeller and converts velocity into pressure in the diffuser. When flow is too low, the impeller outlet pressure cannot overcome the condensing pressure. Gas flows backward; flow re-establishes; pressure builds; the cycle repeats. That is surge.
Two variables decide whether the point enters the surge zone: flow and condensing pressure. Flow is set by load and vane position. Condensing pressure is set by the cooling side: water temperature, water flow, condenser fouling and refrigerant charge. Low load pushes the point left; high condensing pressure pushes the surge line right. Together they close the margin.
3. Seven causes, in diagnostic order
The first four account for most events.
| Order | Cause | How to check | Direction |
|---|---|---|---|
| 1 | Low cooling load | Load below 35–40%; vanes nearly closed | Moves operating point left |
| 2 | High cooling-water temperature | Condensing pressure and approach | Moves surge line right |
| 3 | Low cooling-water flow | Pump status, valve position, filter | Raises condensing pressure |
| 4 | Fouled condenser | Water-side ΔT and approach | Raises condensing pressure |
| 5 | Overcharge | Subcooling and liquid level | Raises condensing pressure |
| 6 | Vane actuator fault | Vane feedback vs command | Prevents opening |
| 7 | Refrigerant undercharge | Subcooling, approach, discharge temperature | Reduces flow and pressure |
Cooling-water ΔT is the quick discriminator. A design ΔT of 5 K that falls to 2–3 K at normal flow indicates reduced heat transfer (fouling or low flow through the bundle). A ΔT of 8 K with low flow indicates a water-side restriction. The remedies are opposite: clean the condenser in the first case; open valves and check the filter in the second.
4. Field response: protect the machine first
Open the vanes or raise the load. Increase the chilled-water load or lower the setpoint to move the operating point right.
Reduce the number of running units. If the load cannot be raised, consolidate the load onto fewer machines so each runs at a higher percentage.
Use hot-gas bypass if fitted. Bypass maintains flow through the impeller, but it wastes cooling capacity. It is a temporary protection measure, not a normal operating mode.
If surge persists, stop the machine and inspect the cooling side. Do not tolerate sustained surge. Even with bypass, the cyclic vibration fatigues the impeller, loosens the vane mechanism and damages the shaft seal. Investigate within the shift.
5. Three anti-surge measures
Vane control. Closing the inlet vanes reduces flow, but below about 30% opening the pre-swirl is strong, efficiency falls and the machine approaches the surge line. Vanes alone cannot prevent surge at very low load.
Variable-speed drive. Reducing speed moves the surge line left. At 60% speed, the surge flow may fall to about 35% of nominal, allowing stable operation at 20% load. This is the most effective measure, at the cost of a VFD.
Hot-gas bypass. Returns some discharge gas to the evaporator to maintain impeller flow. It does not solve the cause; it trades cooling capacity for stability. Expect a 10–20% efficiency penalty. Use it as a fallback.
6. Prevention: keep the point in the safe zone
Stage the machines correctly. Three smaller units can run one at high load instead of two large units at low load. This is the source-level fix.
Set a minimum load. In the plant sequence, set “minimum load per running unit 35%”. Below that, stop one unit or enable bypass. Do not let a machine sit at 20% load for hours.
Manage cooling water. Clean the tower fill, modulate fans by water temperature, and treat the water to prevent scaling. Each measure reduces the probability of high condensing pressure.
Inspect before the season changes. Before summer, check the vane actuator, clean the condenser and verify the charge. This is the highest-value maintenance window.
Log the event. Record load, cooling-water temperature, vane position and high pressure at every surge. After a dozen events, a pattern usually emerges — for example, above a certain water temperature or below a certain load. Use that pattern to set the sequence threshold.
7. Boundaries
This article applies to centrifugal chillers. Screw chillers do not surge; low-load noise has a different cause. Magnetic-bearing centrifugal machines have a wider speed range and a surge line further left, but the physics is the same and high condensing pressure can still cause surge. Older machines may have limited anti-surge logic and depend more on the operator.
Frequently asked questions
What does surge sound and look like?
A deep, cyclic booming or rattling, compressor current pulsing, discharge pressure oscillation and chilled-water temperature instability. It can be mistaken for a bearing fault. Confirm with the operating point and the condenser approach, not sound alone.
What is the operating point?
The intersection of the compressor’s head-flow curve and the system resistance. Surge occurs when head is too high for the flow. Read the pressure lift, the guide-vane position and the cooling-water temperatures to locate the point.
How does cooling-water delta T help?
A rising condenser approach and a smaller delta T at fixed load suggest fouling or low water flow, which raises head. If the delta T is normal but the lift is high, the issue may be low load or a control valve. Measure both.
Could fouling cause surge?
Yes. Fouled condenser tubes raise condensing pressure and head, pushing the compressor toward surge. Clean tubes, verify water flow and check the approach. Do not adjust the surge line before confirming heat transfer.
What about low load?
At low load, flow through the impeller can fall below the surge limit. The guide vanes or a hot-gas bypass should keep flow above the limit. If the chiller is oversized, it may surge at part load even with a clean condenser.
How is surge corrected?
Move the operating point: clean the condenser, restore water flow, raise the load, adjust vane control, or use a variable-speed drive with a surge map. Repetitive surge needs a control review, not just a reset.
What is the risk of repeated surge?
Axial thrust and vibration damage bearings and seals, and the motor can overheat. It also causes chilled-water temperature swings. Treat repeated surge as a mechanical risk, not a nuisance alarm.
When should the compressor be opened?
If surge continues after heat transfer, flow and control are corrected, inspect the impeller, bearings and seals. Metal debris or a rubbed clearance explains why the surge line moved. Do not open the machine before the operating data is reviewed.
Related reading
Refrigerant leak detection · Electroplating chiller corrosion · High-altitude chiller selection