Heat pumps · Chillers · Sludge drying systems
Drying · Reduction · Integrated

Sludge Dryer Selection: Seven Inputs, One Guarantee

Sludge dryer selection is usually presented as a capacity and a price. The capacity is often a round number, the price is per metric ton, and the moisture is “about 80% to 30%”. That is not enough to guarantee anything.

This article turns the selection into seven inputs and one guarantee table. The example is 10 t/d of wet sludge at 80% moisture, dried to 30%.

The seven inputs

Input Example Why it matters
Wet feed 10 t/d Sets the plant size
Feed moisture 80% wet basis Sets the water load
Product moisture 30% wet basis Sets the evaporation
Evaporation 7.14 t/d Sets the heat and airflow
Drying temperature 40–80 °C Sets the technology
Specific energy 0.35 kWh/kg water Sets the operating cost
Material and off-gas Steel, chloride, odor Sets the materials and permit

Each input has a unit and a basis. “80%” without “wet basis” is ambiguous; 80% wet basis is 4 kg water per 1 kg dry solids, while 80% dry basis is 0.8 kg water per 1 kg dry solids. A factor of five error is possible. State the basis in the inquiry.

The mass balance

Dry solids are conserved: 10 t/d × (1 − 0.80) = 2 t/d. At 30% product moisture, the product is 2 / (1 − 0.30) = 2.86 t/d. The water removed is 10 − 2.86 = 7.14 t/d. Over 24 hours, that is 298 kg/h.

The evaporation is the number the dryer must guarantee, not the wet feed. A dryer that accepts 10 t/d at 80% but only removes 5 t/d will not reach 30%. A dryer that removes 7.14 t/d but cannot convey the sludge will also fail. The guarantee should state both the hydraulic capacity and the evaporation.

The guarantee table

Parameter Guaranteed value Test condition
Wet feed ≥10 t/d 80% ±2% wet basis
Product moisture ≤30% Continuous, 72 h
Evaporation ≥298 kg/h 24 h average
Specific energy ≤0.35 kWh/kg water At boundary, 20 °C ambient
Dry solids capture ≥98% Product and condensate
Noise ≤75 dB(A) at 1 m Free field

The specific energy must state the boundary. If the guarantee excludes the feed conveyor, the off-gas fan and the condensate pump, it is not the plant energy. A 0.35 kWh/kg guarantee at the compressor only may be 0.42 at the plant meter. The boundary is part of the guarantee, not an appendix.

Temperature and technology

A low-temperature heat-pump dryer runs at 40–80 °C. It avoids the high-temperature decomposition that produces odor and volatile heavy metals, and it preserves the calorific value for incineration. The trade-off is a larger enclosure and a longer residence time than a high-temperature belt dryer.

A high-temperature dryer at 100 °C or above is smaller for the same evaporation, but it needs a scrubber, a dust filter and a thermal source. For a municipal plant with a strict odor permit, the low-temperature unit is usually the lower-risk choice. For a large centralized plant with waste heat, the high-temperature unit may be the lower-cost choice.

Material and off-gas

The wet side of a sludge dryer sees chloride, sulphide and organic acid. A standard carbon-steel frame may last, but the coil, the fan and the condensate tray need stainless or a coating. A sludge with chloride above 1,000 mg/kg is aggressive; a sludge from a chemical plant may also carry solvents.

The off-gas is not optional. A dryer that removes 7.14 t/d of water produces a large humid air stream with odor. The permit may require a biofilter, a scrubber or a thermal oxidizer. The cost of the off-gas train can be 10–20% of the dryer, so it belongs in the selection, not in the permit stage after the purchase order.

What to ask for

Ask for a mass balance, a heat balance, a guarantee table and a reference plant at the same sludge. A reference at 20% feed moisture is not a reference for 80% feed. A reference at 60% product is not a reference for 30%. The guarantee should be written against the seven inputs, not against a generic capacity.

Ask for the specific energy at the plant boundary and the off-gas treatment power. A dryer that is efficient at the compressor but spends 20% of the energy on the oxidizer is not an efficient plant.

Throughput and redundancy

A single dryer at 100% of the design feed has no margin for a wet week, a maintenance stop or a belt change. A municipal plant usually needs two units at 60–70% each, or one unit with a bypass and a wet-sludge storage of 2–3 days. The storage is cheaper than a second dryer, but it does not cover a breakdown.

The turndown matters as much as the capacity. A dryer that cannot run below 50% will cycle on a dry week and lose efficiency. A heat-pump dryer with variable-speed fans and a modular chamber can turndown to 30–40%. Ask for the turndown curve, not only the maximum capacity.

Boundary

This selection method is for a single dryer with a known sludge analysis. A plant with two sludges, a variable feed or a seasonal load needs a blend and a turndown analysis. A dryer selected on the best week will fail in the worst week.

Common questions

Why is 80% moisture ambiguous?

It can be wet basis or dry basis. Wet basis 80% is 4 kg water per kg dry solids; dry basis 80% is 0.8 kg. The difference is a factor of five in the water load.

How much water is removed from 10 t/d at 80% to 30%?

Dry solids are 2 t/d. At 30% moisture, product is 2.86 t/d. Water removed is 7.14 t/d, or about 298 kg/h over 24 hours.

What should a guarantee include?

Wet feed, feed moisture, product moisture, evaporation, specific energy at a stated boundary, dry solids capture, noise and the test condition.

Is low-temperature drying always better?

It is better for odor and heavy-metal volatility, and it preserves calorific value. A high-temperature plant with waste heat may be cheaper for a large centralized site.

Do I need off-gas treatment?

Usually yes. A 7.14 t/d water removal produces a large humid air stream with odor. The permit may require a biofilter, scrubber or oxidizer.

What reference plant should I ask for?

One with the same feed moisture, product moisture and sludge type. A reference at 60% product is not a reference for 30% product.

What seven inputs?

Feed tonnage, water content, dry solids, hours, temperature, utilities and discharge limit. Miss one and the guarantee moves.

What guarantee?

Throughput, dryness and power per metric ton, with the test method. A bare tonnage promise is not a guarantee.

Further technical reading

For selection mistakes, see Sludge Dryer Selection Mistakes That Show Up in the First Winter. For capacity shortfall, see Sludge Dryer Capacity Shortfall: Eight Causes. For specific energy, see Sludge Dryer kWh/t: Three Denominators. For installation, see Sludge Dryer Installation: Site Conditions and Interfaces.

Related reading

Sludge Dryer Seven Inputs Guarantee · Sludge Dryer Tender Response · Sludge Dryer Heat Balance