Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

High-Altitude Water Chillers: Derating Guide

A chiller selected at sea level and installed at 3,650 m will usually start, run and fail to deliver its rated capacity. The compressor is not the first problem. Air density is. The same fan, running at the same speed, moves the same volume but 36% less mass; the condenser rejects less heat, the condensing temperature rises, and the compressor reaches its high-pressure limit before the load is met.

High-altitude chiller selection is therefore a system correction, not a capacity multiplier applied to the catalog. Air-side heat rejection, fan head, motor cooling, variable-frequency drive (VFD) derating and pump cavitation all change at the same time. This article sets out the corrections in the order they should be applied.

1. What altitude changes

At 20 °C, standard atmosphere gives the following approximate values. The density is calculated from ρ = p ÷ (287 × T), with p in Pa and T in K.

Altitude Pressure Air density Mass flow vs sea level Volume correction
0 m 101.3 kPa 1.20 kg/m³ 1.00 1.00
1,000 m 89.9 kPa 1.07 kg/m³ 0.89 1.12
2,000 m 79.5 kPa 0.94 kg/m³ 0.78 1.28
3,000 m 70.1 kPa 0.83 kg/m³ 0.69 1.45
3,650 m 65.0 kPa 0.77 kg/m³ 0.64 1.56
4,500 m 57.7 kPa 0.68 kg/m³ 0.57 1.75

At 3,650 m — Lhasa is about 3,650 m — the density is 0.77 kg/m³, or 64% of the sea-level value. That single number affects the air-cooled condenser, the fan, the motor and the electrical equipment.

2. Air-cooled capacity: correct the condenser, then the compressor

An air-cooled condenser’s capacity is approximately proportional to the air-side mass flow and the temperature difference. At constant volume flow, the mass flow falls to 64%, so the heat rejection falls to about 64% at the same air temperature rise. In practice, the air temperature rise increases, which partly compensates, but the net capacity correction at 3,650 m is about 0.80–0.85; use 0.82 for a first estimate and confirm with the manufacturer.

For a 480 kW cooling load, a 500 kW sea-level unit derates to 500 × 0.82 = 410 kW, a shortfall of 70 kW or 15%. Selecting a 500 kW unit is not enough. The required sea-level equivalent is 480 ÷ 0.82 = 585 kW, so select 600 kW. The compressor may also need a different displacement or a larger condenser coil, not just a higher fan speed.

Fan law corrections matter. Fan total pressure is proportional to density, so at the same speed the fan produces 64% of its sea-level pressure. If the system resistance is unchanged, the operating point moves down the curve and the volume flow falls by 15–20%. To restore the mass flow, the fan speed must rise by about 15–25%, and the fan power rises by 40–70% (power varies with density and the cube of speed). Check the motor margin and the fan bearing limit before accepting a higher speed.

3. Water-cooled chillers have an advantage, if water is available

At altitude, the wet-bulb temperature is low. At 3,650 m, a design wet-bulb of 11–13 °C is common. A cooling tower with a 4 K approach can supply 15–17 °C water, so the condenser can run at 30–32 °C instead of 40–42 °C at sea level. The lower condensing temperature can improve COP by about 20%, and the water-cooled chiller’s capacity is less affected by air density because the condenser is water-cooled.

The trade-off is water. A 300 m³/h condenser-water circuit with a 5 K range evaporates about 2.5 m³/h; with blowdown, makeup is 3–4 m³/h, or 70–95 m³/d. In a water-scarce region, that is a real constraint, and the tower must be selected for freezing risk in winter and for dust in spring.

If water is available and the project can handle the maintenance, water-cooled is often the better high-altitude choice. If not, the air-cooled unit must be corrected for density and the condenser coil must be larger, not simply the fan faster.

4. Electrical derating is a separate correction

Motors cool themselves with air. At altitude, the lower air density reduces the cooling effect, and the winding temperature rises. The common rule is a 3–8% output derating between 2,000 and 4,000 m, with the exact figure from the motor manufacturer. At 3,650 m, a standard motor may need a 5–10% derating; a high-altitude motor is preferable.

VFDs derate too. A common rule is 1% current derating per 100 m above 1,000 m, so at 3,650 m the drive may need 25–30% derating. The cabinet also runs hotter because the air mass is lower; add 5–8 K to the internal temperature rise, and specify a larger cabinet, a heat exchanger or an air-conditioning unit. Do not assume the drive’s nameplate current is available at altitude.

Insulation coordination changes as well. The dielectric strength of air falls with density, roughly 8–10% per 1,000 m. Clearances and creepage distances that are adequate at sea level may not be adequate at 3,650 m. Use components rated for the altitude, and check the breaker, contactor and terminal clearances.

5. Cavitation: the pump is the hidden failure

At sea level, atmospheric pressure supports about 10.1 m of water column. At 3,650 m, it supports about 6.6 m; at 4,500 m, about 5.9 m. An open tank with the pump suction 2 m below the water surface has only 6.6 − 2 − 0.5 = 4.1 m of available NPSH at 3,650 m, before allowing for water temperature and pipe losses. A pump with an NPSH requirement of 3.5 m is already marginal.

The symptoms are noise, vibration, a falling flow and a pitted impeller. The fixes are: lower the pump, use a closed loop with a pressurized expansion tank, reduce the suction pipe losses, or select a low-NPSH pump. Do not simply add a larger pump; that usually makes the cavitation worse.

For a closed chilled-water loop, the expansion tank pre-charge sets the suction pressure. At altitude, set the static pressure at least 1.0 m above the pump’s NPSH requirement plus the water’s vapor pressure. For a 3,650 m plant, a pre-charge of 2.5–3.0 bar is common, but the exact value depends on the loop height and the pump curve.

6. Commissioning at altitude

Measure the air-side mass flow, not just the volume flow. A 10,000 m³/h fan at 3,650 m delivers 7,700 kg/h, not 12,000 kg/h. If the design mass flow is 12,000 kg/h, the unit is 36% short even though the anemometer reads the design volume.

Record the ambient pressure, the dry-bulb and the wet-bulb at the same time as the capacity test. A capacity test without the pressure is not a valid high-altitude test. Measure the compressor current, the discharge pressure and the condenser approach at full load; compare them with the corrected catalog values, not the sea-level values.

Check the pump inlet pressure and the NPSH margin at the worst case — maximum flow, maximum water temperature. A pump that is quiet at 80% flow can cavitate at 110% flow.

7. Where the correction is not enough

Above 4,000 m with a high cooling load. The air density is below 60% of sea level, and the air-cooled condenser becomes disproportionately large. A water-cooled chiller or a hybrid dry cooler may be the only practical route.

Water scarcity. A water-cooled plant may save energy but cannot be justified if makeup water is unavailable. In that case, consider a dry cooler with a glycol loop, or a heat pump for simultaneous heating and cooling.

Weak grid and high harmonics. VFDs and large motors may disturb the local supply. Check the transformer capacity, the short-circuit ratio and the harmonic limits before adding drives.

Winter operation. A water-cooled tower at 3,650 m can freeze at night. Specify a basin heater, a remote sump or a dry operation mode, and a freeze-stat that starts the pump before the basin reaches 4 °C.

Related reading

High-altitude air-source heat pumps · Air-cooled versus water-cooled chillers · Water-chiller commissioning · Chiller selection margins

Longcom Environmental Protection Equipment Co., Ltd. can correct air-cooled and water-cooled chiller selections for altitude, check motor and VFD derating, and review the pump NPSH margin. For project data, call 400-878-0280 or 13002001280.

Frequently asked questions

How much does altitude derate a chiller?

Air density falls with altitude: about 74% at 2,000 m, 64% at 3,650 m. Air-cooled condenser capacity falls roughly with the reduced mass flow, and fan static pressure drops. Use the manufacturer’s altitude table, not a single percentage.

Why do fans lose head?

Fan laws assume constant density. At altitude, the same fan speed moves less mass and develops less static pressure. The result is lower heat rejection and higher condensing temperature. Fans may need higher speed or a larger diameter.

How do motors derate?

Motors cool less effectively in thin air, and variable-frequency drives may derate too. The nameplate current is not the altitude rating. Check the motor and drive data, and add margin or a larger frame.

What is cavitation risk?

Open tanks and pump suctions see lower atmospheric pressure, so the net positive suction head available falls. Pumps can cavitate at a flow that was fine at sea level. Pressurize the loop or raise the tank.

How should the chiller be selected?

Start with the site altitude and ambient, apply the capacity correction, then check fan and motor limits. Add margin for fouling and part load. Do not select from a sea-level catalog without correction.

What about the cold-water side?

The chilled-water pump and pipe sizing are less affected, but the expansion tank and safety valves see different absolute pressures. Check the system pressure and the pump’s suction margin.

How is performance verified on site?

Measure ambient, condensing pressure, water temperatures and power at a known load. Compare with the corrected curve. If the chiller cannot reach capacity, check airflow and refrigerant charge before blaming altitude.

What should be in the contract?

Site altitude, design ambient, corrected capacity, fan and motor limits, and the test condition. A sea-level guarantee is not valid at altitude. Write the correction into the performance guarantee.

Related reading

Refrigerant leak detection · Centrifugal chiller surge · Pharmaceutical cleanroom chillers