Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

Evaporator Cleaning: The Side the Condenser Article Misses

Condenser cleaning gets the attention because the cooling tower is visible. The evaporator is the other half of the heat transfer, and it is usually the side that is neglected. It is a closed loop, so the water looks clean; the fouling is inside the tubes, behind the strainer and under the biofilm.

This article covers the evaporator water side: what fouls it, how to recognize the loss, which cleaning method to use and how to avoid damaging the tubes. It deliberately does not repeat the condenser descaling procedure.

What fouls the evaporator

Fouling Source Effect
Iron oxide and debris New pipework, steel tank, strainer bypass Deposit on tube inlets; local blockage
Biofilm and slime Low-flow branches, shutdown periods Insulating layer; under-deposit corrosion
Scale Hard makeup water, no softener Thin hard layer; approach rises
Glycol degradation Old antifreeze, overheated loop Acid and sludge; corrosion

A closed loop is not sterile. A branch that is shut off for the winter becomes a stagnant vessel. A strainer that is bypassed during commissioning passes weld slag into the evaporator. A glycol loop that has run for eight years without testing can be acidic and full of suspended solids.

Recognize the loss before you clean

The evaporator approach is the chilled-water leaving temperature minus the refrigerant saturation temperature. Most operators do not have a refrigerant gauge, so use three proxies: the leaving-water temperature at design flow, the evaporator pressure drop and the compressor current.

A rise in the approach of 1–2 K at design flow, with the same load and the same entering water temperature, is a fouling signal. A rise in pressure drop with the same flow is a blockage signal. A compressor current that is higher at the same load suggests the machine is working harder to move the same heat.

Signal Normal Action
Approach 1–2 K at design Clean at +1.5 K, inspect at +3 K
Pressure drop Design ±10% Check strainer and tube inlet at +20%
Leaving water 7 °C ±1 K Check flow before blaming the chiller
Compressor current Design at load Compare at the same condensing condition

Do not clean on a calendar alone. A clean loop with good water treatment may need cleaning every two or three years. A loop with a bypassed strainer may need it in the first season.

Mechanical cleaning

For shell-and-tube evaporators, brush or rod the tubes from the water side. Use a brush sized to the tube inner diameter: too small leaves the deposit, too large can scratch the tube. Nylon or polyester brushes are safer than wire brushes. Push the brush through the tube with water or a low-pressure rod; do not hammer it.

Tube inserts and rotary cleaners can remove soft biofilm, but they do not remove hard scale. For scale, use a chemical clean or a combination: a dispersant first, then a brush. On a brazed-plate evaporator, do not rod; circulate a cleaning solution in reverse flow and backflush.

Chemical cleaning

Use a proprietary scale remover or a citric/EDTA-based product at the supplier’s concentration and temperature. Keep the temperature below 40 °C and the pH within the product’s range. Circulate for the specified time, then neutralize and flush until the return water is clear and the pH is within 0.5 of the makeup water.

Do not leave the chemical in the loop overnight. A weak acid that is safe for a short clean can corrode the tube ends and the solder if it is left stagnant. Do not mix an acid cleaner with a chlorine biocide; the mixture can release chlorine gas.

Method Best for Risk
Brush / rod Loose debris, soft biofilm, shell-and-tube Tube scratch if the brush is oversize
Circulate detergent Biofilm, oil, brazed plate Foam and disposal
Scale remover Hard water scale Acid corrosion if left too long
High-pressure water Heavy debris in large tubes Tube erosion at the inlet

A cleaning procedure that protects the tubes

Isolate the evaporator, drain it and flush with low-pressure water. Open the end cover and inspect the tube sheet. Photograph the inlet before cleaning so you can compare the condition afterward. Brush or circulate, then flush. Refill with treated water, vent and pressure-test. Restart and record the approach at design flow.

If the approach does not improve after cleaning, the problem is not the water side. It may be refrigerant charge, a damaged tube, a bypass valve or a flow sensor. Do not repeat the clean; diagnose the machine.

Water quality and frequency

Test the loop quarterly: pH, conductivity, iron, copper, chloride and suspended solids. Keep a closed loop at a pH of 8.5–10.5 with a corrosion inhibitor, and keep the chloride below the supplier’s limit for the tube material. A loop with a glycol charge needs an annual glycol test; degraded glycol is a fouling source.

Install a strainer with a differential pressure gauge and clean it on the gauge, not on the calendar. A 100-mesh strainer on the chiller inlet is cheap insurance; a bypassed strainer is an expensive habit.

Boundary

This procedure is for the water side of a chiller evaporator. It does not cover refrigerant-side repair, tube replacement or a brazed-plate exchanger that is already plugged. If the pressure drop is high after cleaning and the flow is normal, the exchanger may need replacement, not another chemical clean.

Common questions

How often should the evaporator be cleaned?

On condition, not on a fixed calendar. Clean when the approach rises 1.5–2 K at design flow or the pressure drop rises 20%. A clean loop with good treatment may last two or three years.

Can I use the same chemical as the condenser?

Not automatically. The evaporator is a closed loop with different materials and a different fouling mix. Use a product compatible with the tube and plate materials, and neutralize and flush thoroughly.

Why does the approach rise after cleaning?

If the water side is clean and the approach is still high, check refrigerant charge, a bypass valve, the flow sensor and tube damage. Do not repeat the chemical clean without diagnosing.

Is a brush safe for brazed-plate evaporators?

No. Do not rod a brazed plate. Circulate a detergent or scale remover in reverse flow and backflush. Rodding can damage the plate pack and create a leak.

What water quality should a closed loop hold?

pH 8.5–10.5 with a corrosion inhibitor, chloride below the supplier’s limit, and low suspended solids. Test quarterly; test glycol annually if glycol is used.

What is a normal evaporator approach?

About 1–2 K at design flow for a clean shell-and-tube machine. The exact value depends on the exchanger and the refrigerant; trend it against the commissioning baseline.

Why clean the evaporator?

Fouling raises approach and reduces capacity. The evaporator is a closed loop but not clean; debris, scale and biofilm accumulate. Clean when approach exceeds the design.

How do I clean without damaging tubes?

Use the specified brush or a gentle circulation, not aggressive acid. Flush and neutralize. Avoid excessive velocity on thin-wall tubes.

Further technical reading

For the condenser side, see Chiller Condenser Descaling. For heat transfer, see Chiller Evaporator and Condenser Heat Transfer. For water treatment, see Cooling Water Treatment: Scale, Corrosion and Biofilm. For maintenance, see Water Chiller Maintenance Schedule.

Related reading

Chiller water treatment · Chiller plant sensors · Chiller plant group control