Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

Chiller’s Four Core Components: What to Inspect

A chiller datasheet lists hundreds of numbers, but the machine is built around four components: compressor, evaporator, condenser and expansion device. The differences that matter in service are not the names but the type: screw, centrifugal or scroll; flooded or direct-expansion; high-efficiency tube or plain tube; thermostatic or electronic expansion valve. Each type has its own failure pattern and its own inspection readings.

The criteria below are for conventional shell-and-tube water-cooled machines. Air-cooled and low-temperature units differ, and the manufacturer’s service data always takes precedence.

1. Compressor: the type decides the control

Screw. A pair of intermeshing rotors compresses the gas. Capacity is controlled by a slide valve, typically from 25% to 100%, and the machine runs at about 2,900 r/min. It is the mainstream choice from 200 to 1,500 kW. It depends on oil, so oil quality shows up in vibration and current. Common faults are bearing wear and a sticking slide valve.

Centrifugal. A high-speed impeller accelerates the gas and a diffuser converts the velocity into pressure. It is common above 800 kW, with speeds above 10,000 r/min. Capacity is controlled by inlet guide vanes or a variable-speed drive. It has good part-load efficiency but can surge at low load; hot-gas bypass or VSD anti-surge control is needed. Common faults are surge and guide-vane actuator failure.

Scroll. Two spiral wraps compress the gas. It is simple, has few parts and is common below 100 kW. Capacity is controlled by multiple heads or a VSD; a single scroll has no continuous unloading. It is almost maintenance-free, but liquid slugging and contactor or capacitor failure are the usual problems.

Type Typical range Capacity control Maintenance focus Typical fault
Screw 200–1,500 kW Slide valve, 25–100% Oil, oil filter, oil level Bearing wear, slide valve sticking
Centrifugal Above 800 kW Guide vanes or VSD Bearings, surge protection Surge, actuator failure
Scroll Below 100 kW Multiple heads or VSD Almost none Liquid slugging, contactor

A quick site check is the nameplate speed and the oil requirement: a screw at about 2,900 r/min needs periodic oil changes; a centrifugal at above 10,000 r/min is often oil-free or low-oil; a scroll is a sealed unit and normally does not need oil changes.

2. Evaporator: flooded or direct-expansion

In a flooded evaporator, the shell is filled with liquid refrigerant and the chilled water flows inside the tubes. Heat transfer is good and the approach temperature is small, but the charge is large and the machine is sensitive to oil carry-over. In a direct-expansion evaporator, the refrigerant evaporates inside the tubes and the water flows in the shell. The charge is smaller and the response is faster, but the distribution must be good or some tubes starve.

Inspection: compare the evaporator approach (chilled-water leaving temperature minus evaporating saturation temperature) with the design. An increasing approach at a normal water flow points to fouling on the water side or oil on the refrigerant side. Check the water pressure drop as well: a high drop with a low flow means fouling or a partly closed valve.

3. Condenser: high-efficiency tube or plain tube

The condenser is the other half of the heat-transfer pair. High-efficiency tubes have internal or external fins and a larger surface per unit length; plain tubes are easier to clean and may be preferred where water quality is poor. The condenser approach (condensing saturation temperature minus cooling-water leaving temperature) is the key reading. A rising approach at design water flow and temperature means fouling, scale or air ingress.

Do not clean only the condenser and ignore the evaporator. Both heat exchangers have a water side, and both can foul. A chiller with a clean condenser and a fouled evaporator will show low capacity and a low suction pressure, not a high condensing pressure.

4. Expansion device: thermal or electronic

A thermostatic expansion valve uses a bulb and a diaphragm to hold a superheat set point. It is simple and robust, but the superheat varies with load and the valve cannot be optimized for all conditions. An electronic expansion valve uses a stepper motor and a controller, holds superheat more tightly and can be integrated with the unit controller. It is more efficient at part load but needs a position feedback and a controller setting.

Inspection: measure the pressure drop across the valve and the superheat at the evaporator outlet. A valve that is stuck open gives low superheat and a risk of liquid return; a valve that is stuck closed or undersized gives high superheat and low capacity. On an electronic valve, check the coil resistance and the controller output before replacing the body.

5. Inspect by symptom, not by habit

Reading Normal trend What it suggests
Evaporator approach Small and stable Rising: water-side fouling or oil film
Condenser approach Small and stable Rising: scale, air ingress or low water flow
Suction superheat Per design, stable Low: valve open or overcharge; high: starved evaporator
Discharge superheat Per design High: low charge, high condensing pressure or worn valves
Oil level and color Clear, at the sight glass Dark or foamy: oil degradation or refrigerant carry-over

The four components are a system. A compressor that looks weak may be protecting itself against a blocked evaporator; a condenser that looks fouled may be suffering from air ingress. Read the pressures and temperatures together before changing parts.

Boundary: when the four readings do not hold

The approach, superheat and oil-pressure ranges above are for a conventional water-cooled shell-and-tube machine at steady load. Five common configurations shift the ranges enough that a normal reading can look like a fault, or a fault can look normal.

Case How the reading shifts What to do
VFD chiller Mass flow and approach change with speed Compare at the same speed and load, not against a fixed-speed table
Low-temperature machine Evaporator approach widens to 2–3 K; frost pattern matters Judge frost uniformity, not a single temperature
Air-cooled machine Condensing approach is against ambient air, 8–12 K Do not use the water-cooled 1–3 K range
Plate heat exchanger No tube velocity; pressure drop rises before approach Log water-side ΔP and approach together
Startup or defrost All readings drift until stable Wait at least 30 minutes; water within 0.5 K

The VFD case is the most common source of false alarms. A machine at 50% speed has a lower mass flow and a different approach than the same machine at 100% speed. Compare the reading with the manufacturer’s part-load curve at the same speed, or with a trend from the same operating point. A fixed-speed threshold applied to a variable-speed machine will call a healthy unit fouled.

Refrigerant blends add a second ambiguity. A zeotropic blend has a temperature glide, so the saturated temperature is not one number; using the bubble point for superheat and the dew point for approach, or the reverse, can shift the result by several kelvin. Use the manufacturer’s specified point and the same point in every record. For a plate exchanger, pressure drop is the early indicator and the approach is the confirmation. For an air-cooled machine, ambient air temperature replaces cooling-water outlet. Longcom’s water chiller page lists the applicable ranges by model and refrigerant.

Common questions

Which compressor type is best for a 500 kW chiller?

A screw is the usual choice. A centrifugal at that size is possible but less common; a scroll is used in modular arrays rather than one 500 kW shell.

Flooded or direct-expansion evaporator?

Flooded gives a smaller approach and better full-load efficiency; direct-expansion gives a smaller charge and faster response. The choice depends on the refrigerant, the size and the manufacturer’s design.

Why does the condenser approach rise?

Scale on the water side, air or non-condensables in the refrigerant side, or low cooling-water flow. Check the water flow and the approach at design conditions first.

Can a thermostatic valve be replaced by an electronic one?

Only with the controller and sensor support. The body, the coil and the control logic are a set; a body-only change will not give the expected superheat control.

Is a lower superheat always better?

No. Too little superheat risks liquid return and compressor damage. The target is the manufacturer’s value at the operating condition.

What is the first inspection item?

The water side: flow, pressure drop and approach on both heat exchangers. It is cheaper and more common than opening the refrigerant circuit.

Which component fails first?

The expansion valve or the charge often drifts first; the compressor fails later. Read superheat and subcooling before condemning the compressor.

How do I inspect each?

Compressor by current and vibration; evaporator and condenser by approach; expansion valve by superheat. Each has its own symptom.

Further technical reading

LONGCOM can help specify the compressor, heat-exchanger and expansion-valve configuration for a chiller project, and review the inspection readings against the design. For a component review, contact 400-878-0280 or 13002001280.

Related reading

Evaporator cleaning · Expansion valve operation · Chiller capacity loss