Heat pumps · Chillers · Sludge drying systems
Industrial cooling · Process

Chiller Expansion Valves: Superheat and Failures

The compressor, evaporator and condenser get most of the attention in a chiller. The expansion valve is often reduced to one word on a component list. Yet it performs four jobs at once: it drops the refrigerant from condensing to evaporating pressure, meters the flow to the load, maintains the pressure difference between the two sides, and distributes refrigerant across a multi-pass evaporator. A failure in any one of those jobs looks like something else — low suction pressure, a frosted evaporator, a flooded compressor or a falling oil level.

The diagnostic value of the valve is that its faults are deceptive. A frosted evaporator and low suction pressure look like a refrigerant shortage; a flooded compressor and falling oil level look like an overcharge. In both cases the root cause may be a loose thermostatic bulb or flash gas at the valve inlet. This article follows the sequence: what the valve does, which type fits, how superheat is set, and how the five common failures present.

1. Four jobs, one orifice

Pressure drop. For R134a, a 40 °C condensing temperature corresponds to about 1.02 MPa, and a 5 °C evaporating temperature to about 0.35 MPa. The valve drops 0.67 MPa. For R410A at the same temperatures, the pressures are about 2.43 MPa and 0.93 MPa, a drop of 1.5 MPa. The pressure difference is the first selection parameter, not the nominal cooling capacity.

Flow control. The valve must match the refrigerant flow to the evaporator load. Too little flow leaves the last passes dry and wastes surface; too much flow sends liquid back to the compressor.

Pressure separation. The valve is the only intentional path between the high and low sides. Its resistance determines whether the pressure difference can be established. A fixed orifice can do this reliably, but it cannot adapt to a changing load.

Distribution. A multi-circuit evaporator needs a distributor after the valve. Uneven distribution frosts some circuits first and can reduce capacity by 10–20%.

2. Four types and their boundaries

Type Adjustment Typical capacity Part-load behavior Typical failure
Capillary tube None <5 kW Poor Blockage
Orifice plate None >50 kW Fair Orifice wear
Thermostatic expansion valve Automatic by superheat 3–300 kW Good Bulb failure
Electronic expansion valve Programmable 5–500 kW Best Stepper loss

A capillary tube is a fixed restriction; it is cheap and has no moving parts, but its flow changes with the pressure difference. It suits small, stable appliances, not a chiller with a varying load.

An orifice plate is used in large centrifugal chillers, often as several plates in series to split the pressure drop and avoid flash gas. It is reliable and has no wearing parts, but it cannot adjust; low-load stability comes from hot-gas bypass or variable speed.

A thermostatic valve is the workhorse for screw and medium-sized chillers. It senses suction superheat through a bulb and opens or closes a seat. An electronic valve uses a stepper motor and a controller; it can hold a superheat target, follow a special opening curve during defrost or start-up, and report its position.

The choice is not only capacity. A plant that stays between 60% and 100% load can use a thermostatic valve. A plant that drops below 30% and still needs good efficiency is better served by an electronic valve, because a thermostatic valve at a small opening tends to hunt.

3. The thermostatic valve is a mechanical feedback loop

Three forces act on the diaphragm. The bulb charge pressure pushes from above and tries to open the valve. The evaporating pressure, taken through an internal port or an external equalizer, pushes from below and tries to close it. The spring pushes from below and also tries to close it. At equilibrium, the opening corresponds to a superheat.

When superheat rises, the bulb pressure rises, the valve opens, flow increases, and superheat falls. This is negative feedback without electricity, which is why the valve is reliable and also why it cannot anticipate a load change.

Internal vs external equalizer. An internal equalizer senses the pressure at the valve outlet. An external equalizer senses the pressure at the evaporator outlet through a small tube. On a multi-pass or long evaporator, the pressure drop can be 0.05 MPa or more; an internal-equalizer valve then reads a higher pressure than the true evaporator pressure, stays too closed, and leaves the last passes starved. Use an external equalizer when the capacity is above 30 kW or the evaporator pressure drop exceeds 0.03 MPa.

Superheat setting. The target is usually 5–8 K. Lower superheat uses more evaporator area, but below 3 K the risk of liquid return rises sharply. Higher superheat protects the compressor but leaves surface dry. Each 1 K reduction in superheat uses about 3% more evaporator area; the gain is real but not worth a flooded compressor.

Superheat Evaporator use Liquid return risk Application
2–3 K Highest High at low load Not recommended
5–6 K High Low Standard chiller
8–10 K 5–8% lower Very low Variable load, long lines
>12 K Clearly short None, but starved Investigate the cause

Subcooling is the other side. Each 1 K of subcooling at the condenser outlet adds about 0.8% cooling capacity, so the liquid line needs a subcooler or enough condenser surface. But subcooling obtained by adding condenser area has a capital cost that may not repay itself.

4. Electronic valves: opening by program

An electronic valve is a stepper motor and a needle, with a full stroke of 0–480 or 0–2,000 steps. The controller calculates superheat from the evaporator outlet temperature and pressure, compares it with the target, and outputs a step position through a proportional-integral loop.

Its three advantages are: a variable superheat target (wide during start-up, 5 K at steady load, 8 K at low load to avoid hunting); special actions (full open during defrost, full close at stop to prevent migration, a set position during evacuation or charging); and data (valve position, superheat and body temperature can be sent to the control system, so a technician can see “95% open and still high superheat” and go directly to a blocked inlet or an undersized valve).

The cost is dependence on the control logic. If the proportional band is too narrow and the integral time too short, the valve will oscillate between two positions, the suction pressure will swing, and the symptom will look like compressor surge. A common tuning approach is to start with a wide proportional band and a long integral time, then tighten gradually.

5. Five failures and their field evidence

Bulb loss or poor insulation. Suction pressure is low and superheat is high. The bulb temperature and the suction pipe temperature differ by more than 3 K. Rebind the bulb on a horizontal section at least 0.3 m from the evaporator outlet, never on an oil-return bend or a vertical riser, and insulate it.

Flash gas at the valve inlet. The valve body frosts and flow is unstable. The sight glass shows bubbles. The cause is insufficient subcooling, excessive liquid-line pressure drop or a hot mechanical room. Add subcooling, insulate the liquid line, or shorten the run.

Ice blockage. Cooling stops intermittently; the valve body frosts locally and recovers after warming. Moisture has entered the system and frozen at the orifice. Replace the filter drier and evacuate; do not keep warming the valve.

Dirt or undersize. The valve is fully open and still short of flow. The pressure drop across the valve is high and the strainer is dirty. Clean the strainer and recheck the selection; a valve chosen for full load may be too small at a lower condensing temperature.

Oversize or unstable tuning. Superheat oscillates with a long period, and the valve opening swings widely. A valve selected for peak load may run at 10–20% opening at part load, where its resolution is poor. Select on the common load, or use a valve with a maximum operating pressure (MOP) charge that limits flow at high load.

6. Three selection checks

Pressure difference. The valve’s pressure drop must fall within the catalog range, typically 0.1–1.5 MPa. Too low, and the valve has little control authority; too high, and it reaches its flow limit at a small opening, leaving no modulation margin.

Capacity. Select at the design condition, then check at the minimum load. Catalog capacities are at nominal conditions; apply the correction factors for evaporating and condensing temperature.

Port and connection. The valve port is not the line size. A common practice is one or two sizes smaller than the liquid line, with reducers, to keep the velocity high enough for oil return.

Common questions

Is a frosted valve always blocked?

No. Frost can be normal throttling. The question is whether it is local frost with unstable flow. If the frost is downstream and suction pressure falls periodically, check for ice; if the frost is uniform and superheat is normal, it is normal operation.

What superheat should a chiller run?

5–6 K for a standard chiller, 8 K for a long line or a highly variable load. Do not go below 3 K; liquid return can dilute the oil and damage the compressor.

Can an electronic valve replace a thermostatic valve?

Yes, but the controller must be changed too. The electronic valve needs a drive signal and a superheat algorithm; replacing only the valve leaves it unable to move. Check the communication protocol and the power supply.

Why is superheat lower in summer?

The condensing pressure is higher, so the pressure difference across the valve is larger and the flow is greater at the same opening. The evaporator is more flooded and superheat falls. This is one reason an electronic valve is more stable across the season.

Can a thermostatic valve be adjusted on site?

It has an adjusting screw for the spring preload, usually limited to about two turns. After adjusting, observe for at least 30 minutes before judging. An electronic valve is adjusted in the controller, not by hand.

Does a sight-glass bubble mean low charge?

Check subcooling first. Normal subcooling with bubbles points to a pressure drop or flash gas; low subcooling with bubbles may mean low charge. Adding refrigerant without diagnosing will hide the cause.

Why does the valve ice up?

Moisture condenses and freezes on a cold valve body, especially if the superheat is too low or the valve is oversized. Check the insulation, the superheat setting and the valve capacity. Ice is a symptom, not the cause.

How do I set superheat?

Set it at the manufacturer’s value for the refrigerant and application, then verify at steady load. Too low causes flooding and liquid return; too high starves the evaporator. Adjust in small steps and log the result.

Related reading

Water-chiller fault codes · Refrigerant leak detection and charging · Piston, scroll or screw chillers · Water-chiller maintenance schedule

Longcom Environmental Protection Equipment Co., Ltd. can review expansion-valve selection, set superheat and diagnose valve-related capacity loss on chillers. For project data, call 400-878-0280 or 13002001280.

Related reading

Centrifugal chiller surge · Refrigerant leak charging · Screw compressor oil and Vi