A sludge dryer is not a commodity. The same nominal capacity can behave very differently on a fibrous, gritty or high-salt sludge, and the difference appears in the outlet moisture, the specific energy and the maintenance cost. A manufacturer audit that does not test the actual sludge is a test of the brochure.
The audit has two halves: a pilot or sample test on the site’s sludge, and a factory review of fabrication, controls and service. Both should produce evidence that can be written into the contract.
1. Start with the sludge
Sludge is not a uniform fluid. The important parameters are moisture, dry solids, volatile solids, fiber content, grit, chloride, pH, rheology and the tendency to form a skin or stick to the heat exchanger. A dryer that works on digested sludge may blind on a textile sludge with high fiber, and a dryer that works on a mineral sludge may corrode on a high-chloride stream.
Send a representative sample, not a sample from one day. A 200-liter composite over a week is better than a 20-liter grab sample. Record the sampling point, the date, the polymer dose and the dewatering method.
2. Five evidence categories
| Category | What to verify | Evidence | Why it matters |
|---|---|---|---|
| Pilot or sample test | Outlet moisture, throughput, specific energy, stickiness | Test report with feed and product analysis | Proves the machine on this sludge |
| Heat balance | Evaporation, heat input, losses, recovery | Mass and energy balance at design point | Exposes an optimistic capacity claim |
| Material and corrosion | Wetted parts, chloride, pH, abrasion | Material certificate, corrosion allowance | Determines life, not just first cost |
| Reference plant | Same sludge type, 6–12 months operation | Metered energy, outlet moisture, maintenance log | Shows real performance, not start-up |
| Service depth | Technicians, spares, response, remote support | Organization chart, stock list, SLA | Decides downtime after the sale |
The heat balance is the most revealing document. If the manufacturer claims 1,000 kg/h evaporation with a heat input that cannot physically deliver it, the claim is wrong before the machine is built. Ask for the balance at the site’s feed moisture and ambient, not at a favorable condition.
3. The pilot test protocol
A useful pilot test states the feed, the product, the energy and the time. It runs long enough to reach steady state, usually 4–8 hours, and it records the feed rate, the inlet and outlet moisture, the heat or power input, the condensate, the odor and any sticking or scaling.
The product should be sampled at the end of the run, not during start-up. The outlet moisture should be measured by a standard method (oven drying at 105 °C), not by a hand squeeze. The specific energy should be reported per kg of water removed, so it can be compared across machines.
If the sludge is variable, test the wetter and drier ends of the range. A dryer that passes the average but fails the wet season is a dryer that will be bypassed for part of the year.
4. The factory audit
Fabrication. Check the heat-exchange surfaces, the welds, the frame and the access doors. Look for corrosion allowance, drainage, cleanability and the method of replacing a worn flight or disc.
Controls. Check the interlock between feed, temperature, discharge and condensate. A dryer that continues to feed after the discharge conveyor stops will plug. The control sequence should be visible and testable.
Test capability. Does the factory have a pilot unit, a heat-balance test bench and calibrated instruments? A manufacturer that cannot test its own machine cannot guarantee yours.
Serial traceability. Can the unit be linked to a bill of materials, a weld record and a test report? If not, the quality system is cosmetic.
5. Red flags
No pilot, only a video. A video shows a machine running, not your sludge drying.
Capacity without feed moisture. “1,000 kg/h” at an unspecified inlet is not a capacity; it is a number.
Specific energy omitted. The operating cost is the energy per kg of water removed. A quote that hides it is hiding the largest lifecycle cost.
Material grade not stated. “Stainless steel” is not a grade. 304, 316L and duplex have different chloride limits.
No reference with metered data. A reference list without energy and moisture records is a list of names.
Service only through a distant agent. The response time is a promise, not a local capability.
6. The contract that follows
Feed specification. Moisture range, dry solids, volatile solids, grit and chloride. The guarantee is conditional on the feed, so the feed must be defined.
Performance guarantee. Throughput at design feed, outlet moisture with tolerance, specific energy, noise and emissions. State the test method and the correction for feed variation.
Performance test. A witnessed run at the site, with instruments and samples. Hold a payment milestone against it.
Spares and service. Critical parts for 8–10 years, response time, and a remote-support arrangement.
Training. Operators should know the interlock, the cleaning method and the alarm response. A dryer that is operated by trial and error will not meet the guarantee.
Common questions
Can I skip the pilot test?
Only if the sludge is identical to a reference plant and the manufacturer can show metered data from that plant. Otherwise the pilot is the cheapest risk reduction in the project.
How much sample is needed?
A composite of 100–200 liters is usually enough for a pilot; a smaller sample may be enough for a lab test. Send it in sealed containers and keep it cool.
What should the pilot report include?
Feed and product moisture, throughput, heat or power input, specific energy, condensate, odor and operating problems. A report without energy is a demonstration, not a test.
Is a lower price per kg/h always better?
No. Compare specific energy, outlet moisture, material grade, spares and service. A cheap dryer with a high energy demand can cost more in two years than the price difference.
What is the most common audit finding?
A capacity claim at a favorable feed moisture, with no heat balance and no reference data at the site’s sludge type. The number is real only at the tested condition.
How long should a reference plant have operated?
At least six months, preferably twelve, with metered energy and outlet moisture. A start-up visit is not a reference.
What should a factory audit cover?
Heat balance calculation, coil and fan selection, corrosion margin, control logic, spare list, test bay and reference sites. Ask for the pilot report on your sludge, not only a catalog.
Should I audit before or after the pilot?
After the pilot. The pilot tells you whether the process works; the audit tells you whether the factory can repeat it. Auditing first can miss the process risk.
Further technical reading
- Sludge Dryer Tender Response
- Sludge Dryer Standards and Acceptance
- Sludge Dryer Commissioning
- Sludge Dryer Life and Warranty
LONGCOM can define the pilot protocol, check the heat balance and material grade, and write the performance guarantee before the order. For a supplier audit, contact 400-878-0280 or 13002001280.
Related reading
Dryer FAT witness test · Seven inputs for a guarantee · Dryer commissioning