Surge is a low-flow instability, but it rarely arrives without warning. A centrifugal chiller usually gives four signals before it trips: a change in sound, a swing in current, a vane or flow position at the limit, and a rising condensing approach. The first ten minutes of those signals are worth more than the trip log.
This article is about the precursors, not the post-trip diagnosis. It assumes the machine is running and the operator can observe it.
The sound: a period, not a noise
Surge is a repeating cycle, usually 1–3 seconds. The sound is a low, muffled boom, followed by a quieter period, then another boom. It is not a continuous rumble, and it is not a bearing squeal. The period is the signature: a 1–3 second repeat is the gas reversing at the impeller exit and re-establishing flow.
A single boom can be a valve or a water hammer. A repeating boom with a stable period is surge. If the sound is accompanied by pipe vibration and a current swing, the evidence is strong enough to act before the high-pressure or low-pressure trip.
The current: a swing, not a rise
During surge, the current oscillates. The gas flow reverses, the load falls, then the flow re-establishes, and the current rises again. The ammeter needle or the controller trend shows a periodic swing, often 10–30% of the running current. A steady high current is a different problem: a fouled condenser, an overcharge or a mechanical drag.
Record the current trend for one minute. A 1–3 second period with a 10–30% amplitude is surge. A slow rise over minutes is a heat-transfer problem. The two need different responses; do not add refrigerant to a surging machine.
| Signal | Normal | Surge precursor | First action |
|---|---|---|---|
| Sound | Steady hum | 1–3 s boom cycle | Record, reduce load, check flow |
| Current | Stable ±5% | Swing 10–30% | Do not add charge |
| Vane / flow | 30–100% | At minimum, flow falling | Check load and staging |
| Condensing approach | 3–5 K | Rising toward 6–8 K | Clean condenser, check water |
The vane: at the limit, not at the set point
A centrifugal chiller controls capacity with inlet guide vanes, a VFD or both. The vane position tells you how close the machine is to its minimum flow. If the vane is at its minimum for a sustained period and the load is still falling, the machine is approaching the surge line.
The minimum stable load is usually 25–35% without a VFD, and about 20–25% with one. A vane at 30% opening with a falling load is a warning; a vane at 20% with a falling load is a candidate for shutdown or staging. Do not wait for the trip to decide.
If the plant has multiple machines, stage down before the last machine reaches its minimum. Stopping one machine and returning the remaining machine to 70–80% is better than forcing one machine to 25% and risking surge. The staging logic should use the vane position and the load trend, not only the leaving-water temperature.
The approach: the summer trigger
Surge is not only a low-load event. A high condensing pressure moves the surge line to a higher flow. At 32 °C condenser water, a machine may be stable at 35% load; at 35 °C, it may surge at 45%. The 3 K rise can move the boundary 8–12 percentage points.
The condensing approach is the early indicator. A normal 3–5 K approach that rises to 6–8 K means the condenser is fouled, the water flow is low or the tower is not delivering. The machine may still run, but the surge margin is shrinking. Clean the tubes and check the tower before the machine trips.
What not to do
Do not open the hot-gas bypass to stop the noise and leave it open. A 10% bypass can cut efficiency by 8%; a 20% bypass by 15% or more. The bypass is a protection, not an operating mode. If the bypass is opening regularly, the plant has a staging or load problem, not a refrigerant problem.
Do not add refrigerant to a surging machine. A low charge can cause surge, but an overcharge raises the condensing pressure and makes it worse. Check the subcooling and the approach first; the charge is a cause only when the evidence points there.
Do not reset the trip repeatedly. Each surge event loads the thrust bearing and the seals. A machine that trips three times in a week needs a load and condenser review, not a reset log.
The ten-minute response
Minute 0–2: record the sound, current and vane position. Minute 2–4: check the condensing approach and the tower. Minute 4–6: check the load and the staging. Minute 6–8: decide to reduce load, stage down or stop. Minute 8–10: if the machine is stable, trend the readings; if not, stop it and call service.
The goal is not to keep the machine online at any cost. The goal is to protect the compressor and keep the plant online. A staged shutdown is cheaper than a bearing replacement.
Boundary
This precursor method is for a centrifugal chiller with a guide vane or a VFD. A screw or scroll machine does not surge in the same way. A magnetic-bearing centrifugal has a different dynamic response; follow the manufacturer’s protection logic.
Common questions
What does surge sound like?
A low, muffled boom repeating every 1–3 seconds, often with pipe vibration. A continuous rumble or a bearing squeal is a different problem.
Does current rise or swing during surge?
It swings, often 10–30% of running current, because the flow reverses and re-establishes. A steady high current points to a fouled condenser or overcharge.
Why does surge happen in summer?
A higher condensing temperature raises the pressure ratio and moves the surge line to a higher flow. A 3 K rise in condenser water can move the boundary 8–12 points.
Can I use hot-gas bypass to keep running?
Only as protection. A 10% bypass can cost 8% efficiency; a 20% bypass 15% or more. If it opens regularly, fix the staging or the condenser.
What is the minimum load?
About 25–35% without a VFD, 20–25% with one. A vane at its minimum with a falling load is the precursor to stage down or stop.
Should I reset the trip?
No. Record the sound, current, vane and approach first. Repeated resets load the thrust bearing and seals; the cause is load or condenser, not the reset button.
Which signal comes first?
The sound cycle and current swing usually appear before the pressure trip. The guide-vane position and rising condensing approach follow. Trend them together; a single alarm is too late to protect the machine.
What should the control do before trip?
Open the guide vanes, reduce head, start a bypass or unload the compressor. The control should act at the first precursor, not wait for the high-pressure switch. Log the event for diagnosis.
Further technical reading
For post-trip diagnosis, see Centrifugal Chiller Surge: Diagnose the Operating Point. For head, flow and minimum load, see Centrifugal Chiller: Head, Flow and Minimum Load. For the type comparison, see Screw versus Centrifugal Chillers. For staging, see Why Chillers Are More Efficient at Part Load.
Related reading
Centrifugal chiller surge · Centrifugal head-flow and minimum load · Chiller plant sensors